Phanteks Glacier RTX 2080Ti Gigabyte Aorus GPU Full Water User Manual
GLACIER G2080Ti |
GIGABYTE XTREME |
|
PH-GB2080TiGB_BK01/CR01 |
|
INSTALLATION GUIDE V1.1 |
PACKAGE CONTENTS |
|
For latest version check www.Phanteks.com |
GLACIER GB2080TiGB |
Thermal Pads |
Thermal Compound |
QTY: 1 |
QTY: 3 |
PH-NDC-01 |
|
|
QTY: 1 |
GLACIER Stop Fitting |
M2.5x5 Screws/Washers |
Phanteks D-RGB Cable |
QTY: 2 |
QTY: 10/10 |
QTY: 1 |
WARNING - This product is intended for advanced users. Improper installation may result in damage to your equipment. While all e orts have been made to provide the most comprehensive information possible, Phanteks assumes no liability expressed or implied for any damage(s) occurring to your components as a result of using Phanteks cooling products, either due to mistake or omission on our part in the below instructions, or due to failure or defect in the Phanteks cooling products. Do not disassemble the water block. Warranty will be voided.
Turn o the power to your system and discharge your body’s static electric charge before proceeding with the installation procedure. If you do not feel comfortable with performing the installation procedure, consult a quali ed computer technician.
STEP 1. REMOVING STOCK COOLER
Unscrew all highlighted screws to remove the stock cooler.
No need to remove the backplate.
Make sure to unplug the LED and Fan cables when you remove the stock cooler.
Take the EVA-Foam from the box to use
as a base for your installation process.
STEP 2. APPLYING THERMAL PASTE & PADS
Clean o the original thermal compound. We recommend using isopropanol alcohol.
Apply a drop of the Phanteks Thermal Compound to the center of the GPU chip
Remove the protective lm and place the the thermal pads on correct position on the PCB.
Make sure to remove the protective lm on both sides of the thermal pads.
RTX 2080Ti |
|
|
|
|
3 |
3 3 |
3 |
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
|
|
|
|
1 |
|
|
|
|
|
|
|
3 |
1 2 |
|
|
|
|
|
|
|
5 |
4 |
|
|
3 |
||
|
|
4 |
|
3 |
3 |
3 3 |
|
|
|
||||
|
|
|
|
|
|
3 |
|
||||||
|
|
|
|
|
|
|
|
|
|||||
3 |
3 |
3 |
3 |
3 |
3 |
3 |
3 |
|
3 |
3 |
3 |
|
|
|
|
|
|
2 |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
|
|
|
|
|
|
|
|
|
|
RTX 2080 |
|
|
|
|
3 |
3 |
3 |
3 |
|
||||
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
3 |
|
|
3 |
|
|
|
|
|
1 |
|
|
|
|
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
1 2 |
||
|
|
|
|
|
3 |
3 |
3 3 |
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|||
3 |
3 |
3 |
3 |
3 |
3 |
3 |
3 |
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|
STEP 3. MOUNT THE WATER BLOCK |
9x |
Carefully position the water block onto the |
5x |
|
|
graphics card. Align the mounting holes on |
|
the PCB with the holes on the water block. |
|
Secure the water block with 9 M2.5x5mm screws and 5 washers to the PCB.
Make sure to lay the GPU with the water
block at down without resting on the
PCI bracket.
STEP 4. CONNECT D-RGB LIGHTING
Connect the D-RGB cable to the D-RGB strip in the water block.
All Phanteks D-RGB products can be
daisy-chained together.
You can connect the D-RGB cable to a 
compatible motherboard with the cable that is included with the motherboard.
STEP 5. INSTALLING FITTINGS
Install G1/4 threaded male ttings and close the remaining ports with the two included Stop Fittings.
Always perform a leak test before providing power to any system components.
5x screws + washer
+ 
4x screws only
Connect to
Phanteks Case / Motherboard Cable
Loading...