Phanteks Glacier RTX 2080 ASUS Dual Evo Edition User Manual
GLACIER G2080 ASUS |
DUAL EVO |
|
PH-GB2080ASDEVO_BK01/CR01 |
|
INSTALLATION GUIDE V1.0 |
PACKAGE CONTENTS |
|
For latest version check www.Phanteks.com |
GLACIER |
Thermal Pads |
Thermal Compound |
PH-GB2080ASDEVO |
QTY: 3 |
PH-NDC-01 |
QTY: 1 |
|
QTY: 1 |
GLACIER Stop Fitting |
M2.5x5 Screws/Washers |
Phanteks D-RGB Cable |
QTY: 2 |
QTY: 15/15 |
QTY: 1 |
WARNING - This product is intended for advanced users. Improper installation may result in damage to your equipment. While all e orts have been made to provide the most comprehensive information possible, Phanteks assumes no liability expressed or implied for any damage(s) occurring to your components as a result of using Phanteks cooling products, either due to mistake or omission on our part in the below instructions, or due to failure or defect in the Phanteks cooling products. Do not disassemble the water block. Warranty will be voided.
Turn o the power to your system and discharge your body’s static electric charge before proceeding with the installation procedure. If you do not feel comfortable with performing the installation procedure, consult a quali ed computer technician.
STEP 1. REMOVING STOCK COOLER |
Remove backplate |
Unscrew all highlighted screws to remove |
- 5x screws |
|
|
the backplate and cooler. |
|
Make sure to unplug the LED and Fan cables when you remove the stock cooler.
Take the EVA-Foam from the box to use 
as a base for your installation process.
Remove cooler - 7x screws
STEP 2. APPLYING THERMAL PASTE & PADS
Clean o the original thermal compound. We recommend using isopropanol alcohol.
Apply a drop of the Phanteks Thermal Compound to the center of the GPU chip
and place the thermal pads on correct position on the PCB.
Follow the correct thermal pad placement speci c to your Dual EVO model.
Make sure to remove the protective lm on both sides of the thermal pads.
Dual 2080 EVO |
|
3 |
3 |
3 |
3 |
|
|
||||||
Dual 2070 EVO |
|
|
|
||||||||||
|
3 |
|
|
|
|
|
|||||||
Dual 2070 Super EVO |
|
|
3 |
|
|
||||||||
3 |
|
|
1 |
2 |
|||||||||
Dual 2060 Super EVO |
|
|
3 |
||||||||||
|
|
|
|
|
|||||||||
|
|
|
4 |
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
3 |
3 3 |
|
|
|
|
|
|
|
3 |
3 |
3 |
3 |
3 |
3 |
3 |
3 |
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
|
|
|
|
|
|
|
|
Dual 2080 Super EVO |
3 |
3 |
3 |
3 |
|
|
|||||||
Dual 2080 Super EVO v2 |
|
|
|||||||||||
3 |
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
3 |
|
|
|
|
|
|
|
1 |
|
|
|
3 |
|
|
5 |
2 |
|
|
|
4 |
|
3 |
3 |
3 3 |
|
|
3 |
||||
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
||||
3 |
3 |
3 |
3 |
3 |
3 |
3 |
3 |
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
|
|
|
|
|
|
|
|
STEP 3. MOUNT THE WATER BLOCK
Carefully position the water block onto the graphics card. Align the mounting holes on the PCB with the holes on the water block.
Secure the water block with 8 M2.5x5mm screws and washers to the PCB.
Make sure to lay the GPU with the water 
block at down without resting on the
PCI bracket.
8x
8x
STEP 4. RE-INSTALL THE BACKPLATE |
5x |
|
Carefully position the backplate onto the graphics card. Align the mounting holes on the PCB with the holes on the backplate.
Secure the backplate with 5 M2.5x5mm screws to the PCB.
STEP 5. CONNECT D-RGB LIGHTING
Connect the D-RGB cable to the D-RGB strip in the water block.
All Phanteks D-RGB products can be
daisy-chained together.
You can connect the D-RGB cable to a 
compatible motherboard with the cable that is included with the motherboard.
STEP 6. INSTALLING FITTINGS
Install G1/4 threaded male ttings and close the remaining ports with the two included Stop Fittings.
Always perform a leak test before providing power to any system components.
Connect to 
Phanteks Case / Motherboard Cable 
Loading...