USER MANUAL V1.0
Thank you
for choosing
TABLE OF CONTENTS
1. What’s inside?
Introduction 3
Specications 4
Exploded view 5
Accessories 6
2. Choose your setup
Congure your Evolv X 7
Get started 8
Installing motherboard 10
Installing power supply 11
Installing fans
Connecting the Fan Hub
Installing drives 14
Installing water cooling
Radiator installation
Pump/Reservoir installation
Installing GPU Anti-Sag Bracket 20
12
17
Connecting front I/O 21
D-RGB lighting
Sync lighting with D-RGB motherboard
22
Cable Management 24
Optional Upgrades: 25
Installing vertical GPU 27
Installing Dual System 28
3. Support
Contact us 30
Warranty 31
2
INTRODUCTION
Welcome to Phanteks!
The Evolv X is one of the most versatile mid-tower chassis out there, ready for the
future and the most powerful hardware.
Built from premium materials that are engineered with utmost care and attention
to detail. A design based on continuous product improvement and innovation
throughout the Evolv Series. Discover the ultimate building experience.
Phanteks believes that meaningful designs are created through
The Phanteks team
the fusion of form and function.
3
SPECIFICATIONS
CASE SPECIFICATIONS
Dimension 240 mm x 520 mm x 510 mm
(WxHxD) 94.5 in x 20.5 in x 20.1 in
Form Factor Mid Tower
Materials Anodized aluminum panels
Powder coated steel chassis
Tempered glass side panels
MB Support E-ATX, ATX, Micro-ATX, Mini ITX
Front I/O Power button, 2x USB 3.0,
Microphone, Headphone, D-RGB
Mode button, D-RGB Color button,
USB 3.1 GEN 2 Type-C
Side Window Yes, Tempered glass both sides
PCI SLOTS & DRIVE BAYS
PCI slots 7x
Internal 3.5” 10x (4 included)
Internal 2.5” 9x (6 included)
FAN 120 mm 140 mm
Front 3x 3x (2 installed)
Top 3x 2x
Rear 1x 1x (1 installed)
RADIATOR 120 mm 140 mm
Front Up to 360 Up to 420
Top Up to 360 Up to 280
Rear 120 140
INCLUDED ACCESSORIES
Premium fan 140 mm 3x (installed)
Universal Fan Hub 1x (installed)
3.5” stackable HDD bracket 4x
Vertical GPU Mount 1x
Accessory bag 1x
Anti-Sag Bracket 1x
Airow Cover 1x
Toolbox 1x
CLEARANCE
CPU Cooler Clearance 190 mm (7.48 in)
GPU Clearance 435 mm (17.24 in)
Front Radiator thickness 95 mm (3.74 in)
Top Radiator thickness 65 mm (2.56 in)
SUPPORT
Contact (International) support@phanteks.com
Contact support@phanteksusa.com
(North and South America)
Warranty 5 Years*
*see page 31
4
EXPLODED VIEW
1. Chassis
2. Front Panel
3. Top Panel
4. Side Panels
5. Radiator Bracket
6. PSU Bracket
7. Dual System Cover
8. SSD Covers
9. Airflow Cover
10. Front Dust Filter
11. PSU Filter
3
5
9
7
11
4
6
8
1
4
10
2
5
ACCESSORIES
3.5” MODULAR HDD BRACKET
- 4 included in accessory box
- For 3.5” or 2.5” Drive
VERTICAL GPU MOUNT
- Included in accessory box
- Riser Cable is sold separately
ACCESSORY BAG AND TOOLBOX
GPU Anti-Sag Bracket
PREMIUM FAN 140 MM
- 3 Pre-installed
- Hight static pressure
- Silent operation
AIRFLOW COVER
- Included in accessory box
- Magnetic
ToolboxAccessory bag
M3x5 mm
Motherboard /
SSD / ODD screw
Fan screw
Motherboard
Stando + tool
1x
6x Zip Tie 150mm
Phanteks Logo Badge
6
6-32x6 mm
Hex screw
34x
6-32x6 mm
Thumb screw
12x 6x 16x 3x7x
12x
6-32x5 mm
Case screw
1x
6-32x9 mm
HDD screw
Riser Cable
screw
CONFIGURE YOUR EVOLV X
The EVOLV X has the most versatile chassis design.
With so many possibilities you can use this overview
to choose and plan the best configuration for your
build.
COOLING
WATER
COOLING
STORAGE
DUAL
SYSTEM
PAGE 12
PAGE 14 PAGE 17PAGE 28
7
GET STARTED
PREPARATIONS
The Evolv X case is designed to support installation in standing position.
Don’t turn on the power to your system until installation is complete.
Discharge your body’s static electric charge by touching a grounded
surface before performing any hardware procedure.
Make sure to consult the manuals of your hardware before installation.
If you do not feel comfortable with performing the installation
procedure, consult a qualified computer technician.
8
REMOVING FRONT PANEL
1.
1
2.
2
UNLOCKING SIDE PANELS
REMOVE:
4x
REQUIRE:
3.
OPENING SIDE PANELS
REMOVING TOP PANEL
4.
3
2
Use the 4x thumb screws on the front to
secure the Side Panels during transport or
public events.
LOOSEN:
2x
9
INSTALLING MOTHERBOARD
Use the motherboards screws from the toolbox to install
your motherboard on the pre-installed standoffs.
REQUIRE:
For repositioning
standoffs
STANDOFF POSITIONING
ATX / E-ATX
(Pre-installed)
Micro ATX
install extra standos
Some motherboards require
installation / repositioning
of the standoffs. Please consult
your motherboard manual for
the correct standoff positioning.
By loosening the thumb screws you can
slide the Cable Covers left and right for
optimal cable management.
These standoffs have a special
collar to keep the motherboard in
place when installing vertically.
10
INSTALLING POWER SUPPLY
The power supply can be installed by removing
the PSU bracket on the rear.
1. PUSH
REQUIRE:
LOOSEN:
2x
2. OPEN
1
2
Connect all needed cables to the
power supply before installing it in
the case.
4x
11
INSTALLING FANS
Configure your airflow-path with this overview. All fan locations
support both 120mm and 140mm fans.
Install the magnetic Airow Cover to prevent air from recirculating when you install 2x 120 mm or 2x 140 mm fans.
TOP
REQUIRE:
140
FAN
120
FAN
LOOSEN:
2x
REAR
140
FAN
120
FAN
FRONT
B
A
AIRFLOW COVER
140
120
FAN
FAN
12
CONNECTING THE UNIVERSAL FAN HUB
TO MOTHERBOARD
CONNECT THE FAN HUB 4PIN CABLE TO
YOUR MOTHERBOARD FAN HEADER
1.
CONNECT EXTRA FANS TO THE CORRESPONDING
CONNECTOR ON THE UNIVERSAL FAN HUB
2.
CONNECT THE SATA CABLE TO THE POWER SUPPLY
3.
You can choose a PWM or DC output in the
motherboard settings. The Fan Hub will
automatically translate the signal to all
connected 3- and 4-pin fans.
Check WWW.PHANTEKS.COM/FAQ for more technical
details.
Choosing a PWM output provides the most
customization options in the motherboard
settings.
Expand the number of fans with splitter
cables up to a maximum of 4A total power.
Splitter cables are sold separately:
PH-CB-Y4P / Y3P
FAN HUB 4-Pin
TO PSU
SATA
BLACK 3-PIN
BLACK 4-PIN
WHITE 3-/4-PIN UNIVERSAL
The White Connector will provide the
RPM signal to the motherboard.
13
INSTALLING DRIVES
2.5” SSD INSTALLATION
Both SSD Covers support 3x 2.5” SSDs.
Each SSD is mounted with 4x screws.
REMOVE:
4x
4x
REQUIRE:
CABLES
OPTIONAL SSD STORAGE
Up to 3x additional SSDs can be installed using
the *Phanteks 2,5” SSD bracket (PH-SDBKT_01) .
*SSD brackets are not included and sold separately.
4x
PH-SDBKT_01 required
14
3.5” HDD INSTALLATION
195mm PSU Clearance
250mm PSU Clearance
4x Phanteks Stackable 3.5” HDD Brackets are included.
Additional brackets are sold separately (PH-HDDKT_03).
HDD INSTALLATION STACK / INSTALL REMOVE
REQUIRE:
HDD
1
2
4x
1. LIFT UP LATCH
2. PULL OUT
Each HDD bracket can be stacked
together to offer more flexibility.
The HDD bracket can also house
a 2.5” SSD instead of a 3.5” HDD.
BOTTOM COMPARTMENT
TWO STACK-CONFIGURATION SINGLE STACK-CONFIGURATION
A
C
B
2
1
POSITION A+C
POSITION B
15
MAIN COMPARTMENT
Up to 6 Stackable HDD Brackets can be installed
in the main compartment.
REMOVE THE CABLE COVERS
TO REVEAL THE HDD MOUNTS
1.
Stack the HDD brackets before mounting
if you install more than 1x bracket.
MOUNT THE SINGLE / STACKED
HDD BRACKETS IN POSITION
2.
A
REQUIRE:
REMOVE:
1x
SECURE WITH 2 THUMBSCREWS
3.
B
C
D
E
F
STACKSTACKSTACK
2x
16
INSTALLING WATER COOLING
TOP
12 0 FORM FACTOR
120
240
360
REAR
12 0 FORM FACTOR
120
14 0 FORM FACTOR
140
14 0 FORM FACTOR
140
280
REQUIRE:
Use the Airflow Cover to prevent
hot air from circulating.
2
1
FRONT
12 0 FORM FACTOR
120
240
360
14 0 FORM FACTOR
140
280
420
17
RADIATOR CLEARANCE
TOP FRONT
MAX. RADIATOR CLEARANCE
140mm Radiators: A:405mm B:146mm C:65mm
120mm Radiators: A:405mm B: 126mm C: 65mm*
*If the motherboard and its components (e.g. memory)
are 50mm or lower there is no limit in Radiator thickness.
TOP
A
C
B
B
C
A
FRONT
MAX. RADIATOR CLEARANCE:
A:465mm B: 148mm C: 95mm
Installing a fill port in the top radiator bracket
and/or a drain port in the front of the case
makes water cooling maintenance much easier.
The port diameters are 20.5mm.
Phanteks Passthrough fitting: PH-PTF_BK/CR_G1/4
Phanteks Ball-Valve fitting: PH-BVA_BK/CR_G1/4
FILL PORT
DRAIN PORT
18
RESERVOIR INSTALLATION
Reservoir mounting points are accessed
by removing the Cable Covers.
26mm
REMOVE:
1x
OPTIONAL PUMP BRACKET
The universal Pump Bracket can be installed in
the bottom compartment using 4 case screws.
Pump Bracket sold separately
(PH-PUMBKT_01)
4x
19
GPU ANTI-SAG BRACKET
To prevent your GPU from tipping down you can install the
GPU Anti-Sag Bracket.
INSTALLING GPU ANTI-SAG BRACKET
INSTALL ALL GPU AND PCI CARDS
4
1.
REQUIRE:
20
3
2
PLACE THE GPU ANTISAG BRACKET
2.
INSERT THE THUMBSCREWS WITHOUT
TIGHTENING THEM
3.
PRESS DOWN AND LOCK THE
4.
THUMBSCREWS IN POSITION.
Always loosen the 2 thumb screws
before removing any GPU or PCI card.
2x
CONNECTING FRONT I/O
Please consult the motherboard manual for additional instructions.
There’s no POWER LED +/ - cable. For powering
your Evolv X lighting, please go to page 22.
POWER BUTTON
2x USB 3.0
USB 3.1 GEN 2 TYPE-C
MICROPHONE
HEADPHONE
D-RGB MODE
TO MOTHERBOARD
Power SW
HD
AUDIO
USB 3.0
USB 3.1 GEN 2 TYPE-C
D-RGB COLOR
Please make sure to consult your
motherboard manual before
connecting your front I/O.
21
D-RGB LIGHTING
The integrated D-RGB lighting is plug-and-play and
can be expanded with up to 8 more D-RGB products
from Phanteks.
TO PHANTEKS
D-RGB PRODUCTS
Please connect the 12V SATA connector
to your PSU to power the case lighting.
MODE COLOR
D-RGB CONTROLS
MODE
COLOR
Solid
Breathing
Radar
Sparkle
Rainbow
TO POWER SUPPLY
SATA
TO THIRD PARTY
D-RGB PRODUCTS
All Phanteks D-RGB products can be DaisyChained to optimize cable management.
22
Press & Hold MODE: Turn off Front LED’s.
2 sec
Press & Hold MODE 2 sec again: Turn off all LED’s.
SYNC CASE LIGHTING WITH D-RGB COMPATIBLE MOTHERBOARD
1. Connect the D-RGB motherboard connector to
the motherboard.
D-RGB MOTHERBOARD
To DIGITAL-RGB Motherboard
MOTHERBOARD
D-RGB HEADER
2. Run the Motherboard Lighting software and
follow the instructions to set up your lighting.
Only connect Phanteks D-RGB products to a
3-pin 5V motherboard connector.
ADAPTER
COMPATIBLE WITH
23
CABLE MANAGEMENT
Velcro Ties
Use the velcro ties to route your cables before closing the SSD
Covers. Zip ties are included in the accessory bag to manage any
excess cables.
GPU CABLE ROUTING
24
OPTIONAL UPGRADES
2.5” SSD BRACKET PH-SDBKT_01
For 2.5” SSD Drive
Upgrade up to 3x additional
2,5” SSDs with the optional SSD
brackets.
PAGE 14
3.5” STACKABLE HDD BRACKETS PH-HDDKT_03
For 3.5” or 2.5” Drive
Upgrade up to 6x additional 3,5”
HDDs with the optional HDD
brackets.
PAGE 15
PHANTEKS PH-F120MP / PH-F140MP
High static pressure 120/140 mm fans
More fans can be installed in the Evolv X
and connected to the Universal Fan Hub
using splitter cables.
PAGE 12
DIGITAL-RGB LED COMBO SET PH-DRGBLED_CMBO
High density Digital-RGB LED strips
with magnets
The D-RGB equipped Evolv X is
ready to expand with more D-RGB
lighting products.
PAGE 22
HALOS (LUX) DIGITAL RGB FAN FRAMES
PH-FF120DRGBA PH-FF120DRGBP
PH-FF140DRGBA PH-FF140DRGBP
High density Digital-RGB LED fan
frames that illuminate any fan.
The D-RGB equipped Evolv X is
ready to expand with more D-RGB
lighting products.
PAGE 22
Y-SPLITTER CABLES PH-CB-Y4P / PH-CB-Y3P
4-pin / 3-pin Fan splitters
More fans can be connected to the
Universal Fan Hub using splitter
cables.
PAGE 13
CABLE EXTENSION SET PH-CBCMBO
- Available in multiple colors
- Includes clear cable combs
- Also available as separate cables
Included cables:
- Motherboard 24-pin
- CPU 4+4-pin
- 2x GPU 6+2-pin
25
220 mm Slimline PCI-E x16 Riser Cable 90° PH-CBRS_SL22
220 mm Premium Shielded High Speed PCI-E x16 Riser Cable 90° PH-CBRS_PR22
Vertical GPU installation
With the optional Riser Cable you can place any 2- or 3-slot GPU vertically.
PAGE 27
ITX Upgrade Kit PH-ITXKT_02
Dual System installation
With the optional Riser Cable you can
place any 2- or 3-slot GPU vertically for
your 2nd ITX system.
PAGE 28
Revolt X Power Supply PH-P1000PS
PH-P1200PS
Dual System installation
T he Revolt X power supply unlocks the
Dual System Conguration. But also works
great as a “single system” power supply.
PAGE 11
600 mm Premium Shielded High Speed PCI-E x16 Riser Cable 90° PH-CBRS_PR60
Vertical GPU installation for 2nd system (Dual system conguration)
With the optional Riser Cable you can place any 2- or 3-slot GPU
vertically for your 2nd ITX system.
PAGE 29
26
INSTALLING VERTICAL GPU
INSTALL RISER CABLE
1.
Riser Cable sold separately
(PH-CBRS_SL22)
2x
INSTALL VERTICAL GPU MOUNT WITH 2X SCREWS
2.
REQUIRE:
2x
The GPU Mount has 2 mounting positions.
Position A allows for better air cooling
and 3-slot GPU cards.
A
B
27
INSTALLING DUAL SYSTEM
ITX Bracket sold separately (PH-ITXKT_02)
The Revolt X power supply from Phanteks
is required for this conguration.
REMOVE THE DUAL SYSTEM COVER FROM
1.
THE CHASSIS.
REMOVE:
2x
REQUIRE:
INSTALL YOUR ITX MOTHERBOARD ON THE BRACKET
2.
USING THE INCLUDED MOTHERBOARD SCREWS
Motherboard screws and ITX bracket
screws are included with the ITX bracket
(PH-ITXKT_02)
4x
CONNECT THE POWER
3.
SWITCH AND LED CABLE
INSTALL THE ITX BRACKET
4.
WITH 4X ITX BRACKET
SCREWS
4x
1
TO ITX MOTHERBOARD
Power SW
Power LED
4
28
VERTICAL GPU SECOND SYSTEM
REQUIRE:
INSTALL RISER CABLE
1.
Riser Cable sold separately
(PH-CBRS_PR60)
2x
INSTALL VERTICAL GPU MOUNT WITH 2X
2.
SCREWS
Depending on your needs, it’s not always necessary
to install a GPU for your second system when your ITX
motherboard is equipped with an onboard GPU.
MOVE VELCRO TIE
3.
REMOVE:
1x
2x
The GPU Mount has mounting positions.
Position A allows for better air cooling
and 3-slot GPU cards.
A
B
1x
1x
1x
29
CONTACT US
As a Phanteks customer, you are priority number one. We have a
dedicated team of employees across the globe working hard every day
to make sure we deliver the superior experience you deserve. We are
here for you. If you have a question or a concern about our products,
we have numerous ways you can reach us. Please choose one most
convenient for you to connect with our team.
CUSTOMER CARE
RMA and Technical Support International
Email : support@phanteks.com
Facebook : @Phanteks
RMA and Technical Support Americas
Hours : Monday-Friday 9:00-5:00 PST
Phone number : +1(909)598-2115
Email : support@phanteksusa.com
Facebook : @Phanteks
For up-to-date information please check www.Phanteks.com
30
EV OLV X
PRODUCT PAGE
PHANTEKS
FACEBOOK PAGE
WARRANTY
PHANTEKS warrants its products to be free from defects in material and
workmanship during the warranty period; when given normal, proper
and intended usage. If a product proves to be defective in material or
workmanship during the warranty period, PHANTEKS will, at its sole
option, repair or replace the product with same product or similar
product. The replacement product assumes the remaining warranty of
the original product or 30 days, whichever provides longer coverage for
the customer.
Duration of warranty:
1. Fans - 5 years
2. I/O Ports - 2 years
3. Fan Hub -2 years
4. LED Lighting - 2 years
5. Buttons - 2 years
6. Chassis - 5 years
7. Front and Top Panels - 5 years
Please check www.phanteks.com/Warranty for more information.
31
32
Loading...