Phanteks Eclipse P500A Non-RGB operation manual
ECLIPSE P500A
ECLIPSE P500A
INSTALLATION GUIDE V1.0
OPTIONAL UPGRADES
STEP 9.
a. INSTALL RISER CABLE WITH 2x
RISER CABLE SCREWS.
INSTALL:
2x
STEP 10.
a. INSTALL 4X DUAL SYSTEM STAND-OFFS ON
THE BOTTOM SIDE OF THE ITX BRACKET
INSTALL:
4x
c. CONNECT THE POWER SWITCH & POWER LED
CONNECTOR TO THE MOTHERBOARD
VERTICAL GPU MOUNT - OPTIONAL
INSTALLING A DUAL SYSTEM - OPTIONAL
(RISER CABLE SOLD SEPERATELY PH-CBRS_FL22)
b. INSTALL VERTICAL GPU MOUNT
WITH 2x HEX SCREWS
A
B
A
B
(REQUIRES ITX UPGRADE KIT PH-ITXKT_R01 AND THE REVOLT X POWER SUPPLY PH-P1#00PS)
b. INSTALL ITX MOTHERBOARD
ON BRACKET USING INCLUDED
MOTHERBOARD SCREWS
d. REMOVE THE DUAL SYSTEM
COVER FROM THE CHASSIS
INSTALL:
The GPU Mount has two
mounting positions. Position A
allows for better air cooling and
3-slot GPU cards.
INSTALL:
REMOVE:
2x
2x
4x
INTRODUCTION INCLUDED ACCESSORIES
Thank you for choosing Phanteks. Please take a
moment to carefully go through the manual.
Phanteks will not take responsibility for any
damages incurred due to incorrect installation or
usage of this product.
This manual supports the following models:
PH-EC500ATG_BK (2x 140 mm Black Fans)
PH-EC500ATG_DBK (3x 140 mm D-RGB Fans)
PH-EC500ATG_DWT (3x 140 mm D-RGB Fans)
P500A INCLUDED ACCESSORIES:
2x 140 mm Black or
3x 140 mm D-RGB
22x Motherboard
+ SSD Screw
1x Motherboard
Stando
12x Thumb Screw
7x PSU Screw
3x 2.5” SSD Brackets
(Pre-Installed)
8x Fan Screw
6x Case Screw 3x Riser Cable
Screw
2x 3.5” HDD Brackets
8x HDD Screw Stando
PRODUCT OVERVIEW
CLEARANCE REAR
CPU Cooler Height 190 mm
GPU Clearance 435 mm
Front Radiator Clearance 95 mm
Top Radiator Clearance 65 mm
120
FAN
120
RAD
ECLIPSE P500A BLACK ECLIPSE P500A DIGITAL-RGB
1
2
3
6
77
1
2
3
4
5
140
FAN
140
RAD
FRONT I/O FEATURES
English
1. Headphone / Microphone
2. USB 3.0
3. USB-C Gen 2
4. D-RGB Color
(P500A-D only)
5. D-RGB Mode
(P500A-D Only)
6. Reset Button
(P500A Only)
7. Power Button
Digital-RGB CONTROLS (P500A_D MODEL)
MODE S
SOLID
BREAT HING
R ADA R
SP ARKL E
R AINBOW
TOPFRONT
120
FAN
120
RAD
Francais
1. Casque / Microphone
2. USB 3.0
3. USB-C Gen 2
4. D-RGB Color
(P500A-D Only)
5. D-RGB Mode
(P500A-D Only)
6. Bouton de réinitialisation
(P500A Only)
7. Bouton d’alimentation
CO LO RS
140
FAN
140
RAD
Deutch
1. Kopfhörer / Mikrofon
2. USB 3.0
3. USB-C Gen 2
4. D-RGB Color
(P500A-D Only)
5. D-RGB Mode
(P500A-D Only)
6. Reset-Knopf
(P500A Only)
7. Ein-/Aus Schalter
6x Zip Ties1x Vertical GPU Mount1x Anti-Sag Bracket
4x DualSystem Stando
120
FAN
120
RAD
Espanol
1. Auricular / Micrófono
2. USB 3.0
3. USB-C Gen 2
4. D-RGB Color
(P500A-D Only)
5. D-RGB Mode
(P500A-D Only)
6. Botón de reinicio
(P500A Only)
7. Botón de encendido
Removal Tool
140
FAN
140
RAD
e. INSTALL THE ITX BRACKET
WITH 4x ITX BRACKET SCREWS
INSTALL:
4x
f. (OPTIONAL) IF USING THE X16 RISER CABLE TO INSTALL A VERTICAL
GPU TO SECOND SYSTEM, MOVE THE VELCRO TIE FOR EASY
RISER CABLE ROUTING
(RISER CABLE SOLD SEPERATELY PH-CBRS_PR60)
MOVE:
1x
1x
STEP 1.
REMOVING CHASSIS PANELS
a. OPEN THE LEFT SIDE PANEL,
THEN LIFT UP THE PANEL
TO REMOVE IT.
2
1
PRESS AND HOLD TH E MODE BUT TO N T O TURN O FF LEDS
PRESS AGAIN TO TURN ON
2 SEC
b. LOOSEN THE THUMB SCREWS ON
THE RIGHT SIDE PANEL THEN
SLIDE THE PANEL OFF.
LOOSEN:
2x
c. REMOVE FRONT PANEL BY
PULLING ON THE PANEL
FROM BELOW
ECLIPSE P500A
ECLIPSE P500A
HARDWARE INSTALLATION
STEP 2.
INSTALL THE MOTHERBOARD WITH 9x MOTHERBOARD SCREWS
INSTALL:
9x
STEP 3.
THE POWER SUPPLY IS INSTALLED IN THE REAR OF THE CHASSIS. LOOSEN THUMBSCREWS TO REMOVE PSU BRACKET. INSTALL PSU
TO BRACKET WITH 4x PSU SCREWS.
LOOSEN:
2x
MOTHERBOARD INSTALLATION
MOUNTING POSITIONS
-
FOR M-ATX MOTHERBOARDS.
POWER SUPPLY INSTALLATION
INSTALL:
4x
Plug in all cables you need for
your build into the power
supply rst before installing it
for easier installation
STEP 5.
INSTALL THE SSD DRIVE WITH 4x SSD SCREWS
AND MOUNT INTO THE CHASSIS.
INSTALL:
4x
STEP 6.
STORAGE INSTALLATION - 2.5” SSD
GPU ANTI-SAG BRACKET INSTALLATION
a. PLACE THE GPU ANTI-SAG BRACKET,
MAKE SURE TO INSTALL ALL GPU
& PCI CARDS BEFOREHAND
b. INSERT THE THUMBSCREWS
WITHOUT TIGHTENING THEM.
c. PRESS DOWN AND LOCK THE
THUMBSCREWS IN POSITION.
STEP 4.
a. INSTALL THE HDD DRIVE INTO ONE
PHANTEKS STACKABLE 3.5” HDD
BRACKET (2x INCLUDED)
INSTALL:
4x
THE BOTTOM COMPARTMENT CAN HOUSE 4X STACKABLE HDD TRAYS. *2x Stackable HDD Trays are included.
POSITION “B” WON’T LIMIT PSU/FRONT RADIATOR CLEARANCE, POSITION “A” ALLOWS FOR FRONT FANS ONLY.
THE MAIN COMPARTMENT CAN HOUSE 6X STACKABLE HDD TRAYS.
a. REMOVE THE CABLE COVER(S) TO
REVEAL THE HDD MOUNTS
STORAGE INSTALLATION - 3.5” HDD
HD D
POSITION A+C
195mm PSU Clearance
b. MOUNT THE (SINGLE/STACKED)
HDD BRACKETS IN POSITION.
b. STACK THE BRACKETS IF USING
MORE THAN ONE. IF NOT,
SKIP THIS STEP
1
2
POSITION B
250mm PSU Clearance
Max Front Radiator Clearance
c. TO REMOVE A TRAY FROM A
STACK, LIFT UP LATCH AND
PULL OUT
c. SECURE WITH 2 THUMBSCREWS
CABLE CONNECTION
STEP 7.
a. CONNECT THE HD-AUDIO &
USB 3.0 CABLES
STEP 8.
a. CONNECT THE SATA CABLE TO THE POWER SUPPLY
CONNECT MORE DRGB PRODUCTS
b. CONNECT DRGB CONNECTOR TO DRGB PRODUCTS c. CONNECT MOTHERBOARD DRGB ADAPTER TO THE
MOTHERBOARD CONNECTIONS
b. CONNECT THE FRONT I/O CABLES TO THE FRONT I/O HEADER ON THE
MOTHERBOARD SEE FRONT I/O HEADER DIAGRAM FOR GENERAL REFERENCE
P500ATG_BK MODEL ONLY:
USB-C
DRGB LIGHTING P500A DRGB ONLY
SATA
ALL MODELS:
MOTHERBOARD FRONT I/O HEADER DIAGRAM
POWER LED
POWER SWITCH
Diagram is a general overview.
For a more accurate overview of
your motherboard, please consult
that motherboards’ manual.
Power LED
HDD LED
SYNC YOUR CASE LIGHTING TO THE MOTHERBOARD OPTIONAL
MOTHERBOARD
NOT USED
RESET SWITCH
REMOVE:
4x
A
B
C
D
E
F
INSTALL:
2x
To DIGITAL-RGB Products
To D-RGB Motherboard (optional)
Compatible with:
ADDRESSABLE ADDRESSABLE
RAINBOW
MOTHERBOARD
D-RGB HEADER
Loading...