Phanteks Eclipse P300A Air operation manual

ECLIPSE P300 / P300A

INSTALLATION GUIDE V1.0

ECLIPSE P300 / P300A

INSTALLATION GUIDE V1.0

CABLE CONNECTION

STEP 8.

HD AUDIO & USB 3.0 CABLES

a. CONNECT THE CABLES TO THE MOTHERBOARD

STEP 9.

MOTHERBOARD CONNECTIONS

RGB LIGHTING  P300 ONLY

(P300A DOESN’T COME WITH RBG CONTROL)

FRONT I/O HEADER CONNECTIONS

b. CONNECT THE CABLES TO THE FRONT I/O HEADER ON THE

MOTHERBOARD (SEE FRONT I/O HEADER DIAGRAM FOR GENERAL REFERENCE)

MOTHERBOARD FRONT I/O

BOTH MODELS P300 / P300A

P300A MODEL ONLY

Power LED

Diagram is a general overview. For a more accurate overview of your motherboard, please consult that motherboards’ manual.

HEADER DIAGRAM

POWER

SWITCH

LED

HDD

RESET

LED

SWITCH

NOT USED

INTRODUCTION INCLUDED ACCESSORIES

Thank you for choosing Phanteks. Please take a moment to carefully go through the manual. Phanteks will not take responsibility for any damages incurred due to incorrect installation or usage of this product.

This manual is applicable for the following products:

PH-EC300PTG PH-EC300ATG

Eclipse P300 / Eclipse P300A

+ SSD Screws

1x Motherboard Stando

12x Fan Screw

5x PSU Screw

120 mm Black Fan (Pre-Installed)

6x Zip Tie18x Motherboard

1x This Manual

PRODUCT OVERVIEW

CLEARANCE

CPU Cooler Height 165 mm PSU Clearance GPU Clearance Front radiator | 240: Front radiator | 280:

200 mm 355 mm 122x315 mm 142x315 mm

REAR

120 FAN

120 RAD

FRONT

120 FAN

120 RAD

140 FAN

140 RAD

TOP

120 FAN

2.5” SSD Bracket (1x Pre-Installed)

3.5” HDD Tray (2x Pre-Installed)

140 FAN

a. CONNECT THE SATA CABLE TO THE POWER SUPPLY

SATA

CONNECT MORE RGB PRODUCTS

b. CONNECT RGB CONNECTOR TO RGB PRODUCTS

OPTIONAL UPGRADES

VERTICAL GPU BRACKET

(PH-VGPUKT-02)

THE PHANTEKS VERTICAL GPU BRACKET CAN BE EASILY INSTALLED IN THE REAR PCISLOT AREA WITHOUT MODIFICATIONS. FOLLOW THE INSTRUCTIONS THAT COME WITH THE VERTICAL GPU BRACKET.

SYNC YOUR CASE LIGHTING TO THE MOTHERBOARD

c. CONNECT MOTHERBOARD RGB ADAPTER* TO THE MOTHERBOARD

*SOLD SEPERATELY (PH-CB_RGB4P)

12V

COMPATIBLE WITH:

12V G R B

MOTHERBOARD RGB HEADER

ECLIPSE P300 FRONT I/O

1. Headphone

2. Microphone

3. USB 3.0

4. RGB Control

5. Power Button

ECLIPSE P300A FRONT I/O

1. Headphone

2. Microphone

3. USB 3.0

6. Reset Button

5. Power Button

RGB CONTROLS (P300 MODEL)

Short Press to change color:

Long Press to change mode:

Solid Breathing Color Cycle

Press and Hold to turn o or switch to motherboard control.

FRONT I/O FEATURES

English

1. Headphone

2. Microphone

3. USB 3.0

4. RGB Control

5. Power Button

6. Reset Button

Deutch

1. Kopfhörer

2. Mikrofon

3. USB 3.0

4. RGB Steurung

5. Ein-/Aus Schalter 6 .Reset-Knopf

Francais

1. Casque

2. Microphone

3. USB 3.0

4. RGB Contrôle

5. Bouton d’alimentation

6. Bouton de réinitialisation

Espanol

1. Auricular

2. Micrófono

3. USB 3.0

4. RGB Controlar

5. Botón de encendido

6. Botón de reinicio

ECLIPSE P300 / P300A

INSTALLATION GUIDE V1.0

ECLIPSE P300 / P300A

INSTALLATION GUIDE V1.0

panel removal

There are three panels that can be removed from the P300(A) Chassis; the left side tempered glass panel, the right side panel and the front panel. Follow these steps below.

STEP 1.

a. LOOSEN THUMB SCREWS AND

SLIDE TO THE LEFT.

LEFT SIDE PANEL

b. TILT PANEL FORWARD. c. PULL UPWARD TO REMOVE.

LOOSEN:

HARDWARE INSTALLATION

STEP 4.

INSTALL THE ATX MOTHERBOARD WITH 9 MOTHERBOARD SCREWS

STEP 5.

INSERT THE POWER SUPPLY INTO THE CHASSIS AND THEN SECURE THE POWER SUPPLY WITH 4 PSU SCREWS

MOTHERBOARD

INSTALL:

POWER SUPPLY

INSTALL:

Micro - ATX

If installing a Micro-ATX motherboard, install the extra stando supplied and consult your motherboard manual for further instructions.

PANEL RE-INSTALLATION

FOLLOW STEPS IN REVERSE ORDER.

STEP 2.

LOOSEN THUMB SCREWS AND SLIDE THE SIDE PANEL OFF.

RIGHT SIDE PANEL

LOOSEN:

STEP 3.

REMOVE FRONT PANEL BY PULLING

FRONT PANEL

ON IT FROM BELOW

STEP 6.

INSTALL THE SSD DRIVE WITH 4 SSD SCREWS AND MOUNT INTO THE CHASSIS.

A SECOND OPTIONAL SSD BRACKET CAN BE INSTALLED.

2.5” SSD DRIVES CAN ALSO BE INSTALLED INTO THE 3.5” DRIVE BAYS.

STEP 7.

REMOVE THE HDD TRAY BY PULLING OUTWARD. INSTALL THE HDD DRIVE IN THE TOOLLES HDD TRAY AND SLIDE THE MOUNTED HDD TRAY BACK INTO THE CHASSIS.

2.5” SSD

INSTALL:

3.5” HDD

With the P300 model you can access the dust lters after removing the front panel. We recommend to clean the dust lters every month for optimal performance.

The HDD Tray can also hold a 2.5” SSD