Pfister JX8-340P User Manual [en, es, fr]

0X8 ● JX8 Series Serie Série

0X8 ● JX8 0X8 ● JX8

TUB & SHOWER

Single Control, Pressure Balancing

Valve Body

Cuerpo de válvula monomando de equilibro

de presión para

BAÑERIA Y DUCHA

BAIN ET DOUCHE

Corps de mitigeur à régulation de pression

Lifetime Limited Mechanical & Pnish Warranty

Price Pster

Covers Pnish and Pfunction for as Long as You

Own Your Home

(Commercial Applications Limit the Duration of the

Warranties as Provided Below)

Price Pster provides the following Warranties for its products. Proof of Purchase may be required in order to obtain any of the benets set forth below.

Limited Warranties: Price Pster warrants that for as long as the original purchaser owns the home in which the Price Pster product (the “Product”) is originally installed, the Product will be free of all defects in material and workmanship that would impair the intended and proper use of the Product. If the Product is installed in a commercial application, the above mechanical warranty shall be limited for a period of ten (10) years from the date of purchase of the Product.

Price Pster warrants against deterioration of the Product’s nish for as long as the original purchaser owns the home in which the Product is originally installed. If the Product is installed in a commercial application, the above nish warranty for Products that do not contain the Pforever nish shall be limited to a period of ve (5) years from the date of purchase.

Exclusive Remedy: In the event of any defect in the Product that breaches the foregoing warranties, Price Pster, at its option, will repair or replace the defective part of the Product. Repair or replacement of the Product is the exclusive remedy.

For any remedy under this warranty, Price Pster is to be notied describing the problem. In order to notify Price Pster and receive assistance or service under this warranty, the original purchaser may: (1) call 1-800-Pfaucet (1-800-732-8238) for a consumer service representative who can assist you, or (2) write consumer service department c/o Price Pster Inc., 19701 DaVinci, Lake Forest, CA 92610, and include a description of the problem, model number, your name, address, phone number and approximate date of purchase, or (3) email Price Pster’s customer service department by going to www.PricePster.com, or (4) notify the location or distributor from which the Product was purchased. In any case, you may be required to return the Product to Price Pster for inspection and proof of purchase may be required.

Limitations and Exclusions: PRICE PFISTER WILL NOT BE LIABLE FOR ANY OTHER DAMAGES OR LOSSES, INCLUDING, BUT NOT LIMITED TO, INCIDENTAL AND/OR CONSEQUENTIAL DAMAGES, REGARDLESS OF THE LEGAL THEORY ASSERTED, INCLUDING ANY CLAIM OR BREACH OF WARRANTY HEREUNDER OR ANY OTHER CAUSE, AND WHETHER ARISING IN CONTRACT OR IN TORT (including negligence and strict liability).

Price Pster has the right to discontinue or modify any product at any time. Some states do not allow limitations or exclusions of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.

The above warranties do not cover damage resulting from improper maintenance, repair, cleaning or installation, misuse, abuse, alterations, accidents or acts of God.

04-01-09 EO7494A

Garantía Mecánica y sobre el Acabado Limitada de por Vida

Cubre las funciones y el acabado por el tiempo en que usted sea

Price Pster suministra las siguientes Garantías para sus productos. Es posible que se requiera la presentación de una Prueba de compra para obtener cualquiera de los benecios indicados a continuación.

Garantías Limitadas: Price Pster garantiza que por el tiempo en que el comprador original sea propietario de la casa en el que se hubiese instalado inicialmente el producto Price Pster (el “Producto”), este Producto estará libre de todo defecto en material y mano de obra que pueda afectar el uso proyectado y correcto del Producto. Si el Producto se instala en una aplicación comercial, la garantía mecánica que antecede estará limitada a un período de diez (10) años a partir de la fecha de compra del Producto.

Price Pster garantiza el acabado del Producto contra deterioro por el tiempo en que el comprador original sea propietario de la casa en la que hubiese instalado inicialmente el Producto. Si el Producto se instala en una aplicación comercial, la garantía sobre el acabado que precede para Productos que no contengan el acabado “Pforever” estará limitada a un periodo de cinco (5) años a partir de la fecha de compra.

Recurso exclusivo: En el caso de que haya un defecto en el Producto que viole las garantías que preceden, Price Pster, a su opción, reparará o reemplazará la pieza defectuosa del Producto. La reparación o el reemplazo del Producto es el recurso exclusivo.

Para todo recurso con respecto a esta garantía, Price Pster deberá ser noticado, con una descripción del problema. Para noticar a Price Pster y recibir ayuda o servicio bajo esta garantía, el comprador original puede: (1) llamar al 1-800-Pfaucet (1-800-732-8238) para hablar con un representante de servicio al cliente que lo pueda ayudar, o (2) escribir al departamento de servicio al consumidor, c/o Price Pster Inc., 19701 DaVinci, Lake Forest, CA 92610 U.S.A., e incluir una descripción del problema, el número del modelo, su nombre, dirección, número de teléfono y fecha aproximada de compra, o (3) enviar un e-mail al departamento de servicio al consumidor de Price Pster entrando en la página web www.PricePster.com, o (4) avisarle al lugar o al distribuidor en donde se compró el Producto. En cualesquiera de los casos, podría pedírsele devolver el Producto a Price Pster para su inspección y es posible que se requiera la presentación de una prueba de compra.

Limitaciones y Exclusiones: PRICE PFISTER NO SE HARÁ RESPONSABLE DE NINGÚN OTRO DAÑO O PERJUICIO, INCLUYENDO, PERO SIN ESTAR LIMITADO A DAÑOS INCIDENTALES Y/O CONSECUENTES, SIN IMPORTAR LA TEORÍA LEGAL A LA QUE SE ALEGUE, INCLUYENDO TODO RECLAMO O VIOLACIÓN DE LA GARANTÍA PRESENTE O CUALQUIER OTRA CAUSA, Y YA SEAN COMO RESULTADO DE LA LEY CONTRACTUAL O LA DE ANTECEDENTES (incluyendo negligencia y responsabilidad estricta).

Price Pster tiene el derecho de discontinuar o modicar cualquier producto en cualquier momento. Ciertos estados no permiten limitaciones o exclusiones de daños incidentales o consecuentes, de manera que es posible que las limitaciones o exclusiones que preceden no correspondan en su caso. Esta garantía le otorga derechos legales especícos y es posible que usted también tenga otros derechos que dieren entre un estado y otro.

Las garantías que preceden no cubren daños y perjuicios ocasionados como resultado de mantenimiento, reparaciones, limpieza o instalación inadecuados, mal uso, abuso, alteraciones, accidentes o causas de fuerza mayor.

Price Pster

propietario de su casa

(Las Aplicaciones Comerciales Limitan la Duración

de las Garantías)

Price Pster

Une garantie limitée à vie

pour ce qui est de l’aspect mécanique et de la nition,

tant et aussi longtemps que vous serez propriétaire

de votre domicile.

(Garantie limitée en cas d’utilisation commerciale

– voir ci-dessous)

Veuillez noter qu’une preuve d’achat peut être requise en cas de recours au titre de la garantie.

Garantie limitée : Tant et aussi longtemps que l’acheteur sera propriétaire du domicile dans lequel le produit Price Pster a été installé, nous lui garantissons que ce dernier sera exempt de tout défaut de matériau ou vice de fabrication pouvant en entraver l’utilisation correcte tel que prévu. Dans le cas des produits d’utilisation commerciale, la garantie exprimée ci-dessus est restreinte à une période de dix (10) ans.

Par ailleurs, tant et aussi longtemps que l’acheteur sera propriétaire du domicile dans lequel le produit Price Pster a été installé, nous lui garantissons un article dont la nition ne pourra se détériorer. Dans le cas des produits d’utilisation commerciale qui ne comportent pas la nition “Pforever”, la garantie est restreinte à une période de cinq (5) ans.

Recours exclusif : En cas de défaut du produit relevant de la garantie, le fabricant pourra, à sa discrétion, réparer ou remplacer la partie défectueuse. Cette mesure constitue un recours exclusif.

Pour tout recours au titre de la garantie, les clients doivent communiquer avec le fabricant pour lui faire part du problème. L’acheteur d’origine peut : (1) composer le 1 800 732-8238 pour parler à un représentant qui l’assistera; (2) écrire au service à la clientèle : Price Pster Inc., 19701 DaVinci, Lake Forest, CA 92610 U.S.A., et fournir une explication du problème, en précisant le numéro de modèle, son nom, son adresse et son numéro de téléphone, ainsi que la date d’achat approximative; (3) communiquer par courrier électronique avec le service à la clientèle en utilisant le site www.PricePster.com, ou (4) aviser le détaillant qui a vendu le produit. On peut être obligé de retourner le produit au fabricant, et une preuve d’achat peut être exigée.

Limitations et exclusions : PRICE PFISTER NE SERA PAS RESPONSABLE DES AUTRES DOMMAGES OU PERTES, Y COMPRIS LES DOMMAG ES INDIRECTS, INDÉPENDAMMENT DE TOUTE THÉORIE Y COMPRIS TOUTE RÉCLAMATION SELON LAQUELLE IL Y AURAIT EU RUPTURE DE GARANTIE, QUE CE SOIT PAR RAPPORT À UN CONTRAT OU PAR VOIE DE NÉGLIGENCE (cela comprend la négligence et la responsabilité stricte).

Price Pster se réserve le droit de discontinuer ou de modier un produit en tout temps. Certaines provinces ne permettent pas l’exclusion ou la limitation des dommages indirects, de sorte que la limitation exprimée peut ne pas s’appliquer. La présente garantie octroie aux clients certains droits d’ordre juridique, et ceux-ci pourraient en avoir d’autres, selon la province où ils habitent.

La garantie ne s’applique pas aux dommages résultant d’un entretien, d’un nettoyage ou d’une installation fautivement effectués, ou encore d’usages fautifs, d'abus, de modications, d'accidents ou de catastrophes naturelles.

JURIDIQUE,

28371-0500

A COMPANY

ENGLISH

Thank you for purchasing this Price Pster product. All Price Pster products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This valve is easy to install using basic tools and our easy to follow

illustrated instructions. If you have any questions regarding this product, call 1-800-Pfaucet (1-800-732-8238).

1 BEFORE PROCEEDING:

INSTALLATION

WARNING: Read all the instructions completely before proceeding. Price

Pster recommends calling a professional if you are uncertain about installing

this product!

This product should be installed in accordance with all local and state plumbing and building codes.

ENGLISH

Use only 1/2” Iron or Copper Pipe between valve and tub spout (No PEX)!

WATER SHUT-OFF:

Locate water supply inlets and shut off water supply valves. These are usually found near water meter.

SURFACE PREPARATION:

For optimum performance of your new Price Pster Single Control Pressure Balancing Valve, a minimum water pressure of 20 PSI is required. Have the

basic tools ready for removal of old valve. If you are replacing an existing Valve, disconnect the old valve and clean the mounting surface thoroughly. Align and adjust water supply pipes to recommended dimensions. For new construction, Install water supply pipes to recommended dimensions.

FINISHED

WALL

/8” - 3 1/2”

SHWR

2 TOOLS RECOMMENDED:

For Iron Pipe Installation:

● PTFE Plumber’s Tape or Thread Sealant ● Slotted screwdriver

● Phillips Screwdriver ● Adjustable wrench ● Pipe Wrench

● Flashlight ● Cloth

For soldered copper and non-standard installations, some additional tools may

be required.

VALVE COMPONENT LESS STOPS

48”

30”

TUB &

SHOWER

ONLY

FLOOR

SHOWER

4 VALVE INSTALLATION

CAUTION: Be sure to position Valve Body (4A) correctly in wall, ”SHWR”

marking up.

Depth (4B) for valve body in wall is measured from center of shower outlet (4D) to nished wall surface (4C). Minimum distance (4B) is 2

is 3

/2". Height is measured from bottom of oor (4E) to center of valve body

(30" for Tub & Shower and 48" for Shower only).

/8" and maximum

VALVE COMPONENT WITH ITEGRAL STOPS

3 CHECKING THE CONTENTS OF THE BOX

These instructions cover six different model types. Upon opening the box, please check to ensure that all of the following items are included with your model type:

A JX8-310P PEX Supply Valve Component Less Integral Stops B 0X8-310A Copper Supply Valve Component Less Integral Stops C JX8-310A Iron Pipe Supply Valve Component Less Integral Stops D JX8-340P PEX Supply Valve Component with Integral Stops E 0X8-340A Copper Supply Valve Component with Integral Stops F JX8-340A Iron Pipe Supply Valve Component with Integral Stops G Shower Only Pipe Plug

If any of these items are missing, please contact Price Pster Consumer Services

at 1-800-Pfaucet (1-800-732-8238).

5 SECURING VALVE BODY

/16” Dia. Screw holes (5B) are provided to secure Valve Body (5A) to framing

(5C) or other solid support. For special direct mount (Thin Wall Installation) go to step 18. For PEX installation, connect PEX lines prior to securing.

ENGLISH

6 7

HOT

IRON PIPE

PEX PIPE

COPPER

PIPE

HOT

COLD

48”

8” Min

7 TUB & SHOWER OUTLET CONNECTIONS

Connect Shower (7A) and Tub (7B) Outlet Pipes to Valve Body (7C). Connect Pipe Elbows (7D) (not included) to ends of both pipes. We recommend using drop elbows (7D) (not included). Securely fasten to framing or other solid support. The height for outlet pipes is measured from the center of pipe elbow to center of the valve body, as shown.

WARNING: For Iron Pipe Connections or threaded ttings, use thread

sealant or PTFE Plumber’s tape according to manufacturer’s instructions.

WARNING: Use only

/2” Iron or Copper Pipe between valve

and tub spout (No PEX)! Do not reduce the inner pipe diameter!

ENGLISH

COLD

6 SUPPLY CONNECTIONS

Proper ttings for your valve body type are required. Connect water Supply Lines (6A) to Valve Body Inlets (6B). Hot water supply lines

go into left inlet. Cold water supply lines go into right inlet. (Supply lines are not included). Please follow manufacturer’s instructions when installing supply lines.

IRON PIPE: Valve Body Inlets (6B) and Outlets (6C) are designed to accommodate 1/2-14 NPT pipe. Use thread sealant or PTFE Plumber’s tape

on all threaded ttings, according to manufacturer’s instructions.

CAUTION: For iron pipes, it is not recommended to reduce outlet pipe

diameter. PEX PIPE: Valve Body inlets (6B) are designed to accommodate a 1/2” PEX

pipe and outlets (6C) are designed to accommodate a 1/2” copper pipe. Remove Plaster Guard (6D).

NOTE: This Valve Body is not to be used with Polybutylene or the Wirsbo

“Expansion” PEX system. COPPER PIPE: Valve Body inlets (6B) and outlets (6C) are designed to

accommodate a 1/2” copper pipe.

WARNING: Remove Plaster Guard (6D), Backup Plate (6E) and Cartridge

Assembly (6F) prior to soldering any inlet or outlet connections. Failure to do so can result in water damage. prior to soldering (see step 12).

For valves with integral stops, open valve stems

30” Min

8 SHOWER ONLY OUTLET CONNECTIONS

Connect Shower Outlet Pipe (8A) to Valve Body (8B). Plug Bottom Outlet (8C) with Pipe Plug (8D). Connect Pipe Elbow (8E) (not included) to end of the pipe. For copper pipe outlets, we recommend using drop elbows (8E) (not included).

Securely fasten to framing or other solid support. The height for the outlet pipe

is measured from center of pipe elbow to center of valve body, as shown.

WARNING: For Iron Pipe Connections or threaded ttings, use thread

sealant or PTFE Plumber’s tape according to manufacturer’s instructions.

ENGLISH

9 10

ENGLISH

10A

10D

10B

ONOFF

10D

10A

10 PRESSURE TESTING VALVE

Use two

and Tub Outlet (10C). Turn Stem (10D) counterclockwise to full on position and check all connections for leaks. Rotate Stem (10D) clockwise to turn off.

Look for leaks from the outlets.

pressure is balanced between hot and cold inlets.

100 PSI.

to relieve pressure.

11 UNIT START UP

Turn on water supplies, and check all connections for leaks.

/2" iron pipe plugs (10A) (not included) on both Shower Outlet (10B)

WARNING: Pressure testing is not to exceed 250 PSI. Make sure

WARNING: Differential pressure of hot and cold inlets must not exceed

CAUTION: Slowly remove pipe plugs (10A) from tub and shower outlets

10C

12A

9 CARTRIDGE REASSEMBLY

Once all pipe joints are soldered, reassemble the Cartridge Assembly (9A) and Backup Plate (9B) into Valve Body (9C). Be sure that Notch (9D) from the Bonnet (9E) is pointing down (For back-to-back installation see step 20).

WARNING: When reassembling unit, be sure that Tabs (9F) from the

Cartridge Assembly (9A) are set properly on the Valve Body groves (9G).

WARNING: When reassembling the Cartridge Assembly (9A) and Backup

Plate (9B), be certain that the placement of the O-ring (9H) is within the groove and not pinched between the backup ange (9G) and casting wall (9J). Failure to do so will result in water leaks and water damage.

12D

12C

12A

12B

12 MODEL WITH INTEGRAL VALVE STOPS

Integral Stops (12A) provide an alternate means to shut off the water supply. With a at head screwdriver (12B), the entire water supply can be shut off by rotating

the valve stem (12C) clockwise. The integral stops can be used for temporary shutting off the water supply to allow access to the cartridge assembly (12D) for maintenance.

ENGLISH

13 15

13C

ENGLISH

15A

13A

13B

13 FLUSHING

For Tub and Shower Combinations

Turn on water supply lines by rotating Stem (13A) counterclockwise allowing water to ow from tub spout outlet (13B) until all foreign matter has cleared the line. Water should not be owing from shower outlet (13C) during this test. If water is owing from shower outlet, please check your valve to see that the casting mark “SHWR” is facing up (see step 4).

15B

15A

15C

15D

14C

14B

14A

14 FLUSHING

For shower Only Installation

Be sure to plug Bottom Outlet with Pipe Cap or Plug (14A) using Thread Sealant.

Rotate stem (14B) counterclockwise, allowing water to ow from shower outlet (14C) until all foreign matter has cleared the line. If water ow becomes low or no ow at all, (refer to Step 20).

15A

15B

15D

15A

15C

15B

LIMITED TRAVELFULL TRAVEL

15 TEMPERATURE ADJUSTMENT

Adjustment Gear (15A) is factory-set to prevent stem from reaching full hot position. To adjust stem rotation: Remove Adjustment Gear (15A). Rotate Stem (15B) counterclockwise to determine a maximum desired temperature. Replace Gear (15A) aligning Adjustment Stop (15C) to stem Tab Surface (15D) so Stem (15B) cannot move beyond adjusted point.

ENGLISH

16A

16B

ENGLISH

NON STANDARD INSTALLATIONS

18B

18C

SHWR

4” Dia

18B

TUB

16 PLASTERGUARD REPLACEMENT

Replace plasterguard (16A) into Valve Body and secure with Screws (16B). Proceed to nish wall.

1 1/4” Dia

4 3/4” Dia

18D

18C

18 THIN WALL INSTALLATION

Knock out Center Section (18A) of Plaster Guard (18B) and remove Screws (18D). For installation of thin walls, use Support Plate (18C) in addition to Plaster Guard (18B). For installation to other wall types, do not use Support

Plate (18C). Use of Plaster Guard (18B) is optional. For center hole on a thin wall use 4” diameter.

18A

19C

1 1/4” Dia

17 FINISH WALL PREPARATION

Make appropriate holes to nished wall. Price Pster recommends that all Tub Spout and Shower Outlet holes be 1

wall use 4

preparing the nished wall.

/4” diameter.

CAUTION: Make sure that leak tests and ushing are performed before

/4” diameter. For center hole on plaster

HOT COLD

19A

19 REVERSED INLET LINES

If hot and cold inlets are reversed (back-to-back installation), (19C) unscrew the plasterguard and bonnet assembly. Rotate the Bonnet Assembly (19A) 180° with Notch (19B) facing up and reassemble.

19B

COLD HOT

19A

180°

+ 14 hidden pages