Contact Points Testing Light Kit Charger and USB Cable
with Rubber Caps
PACKAGE:
1x Remote Transmitter
1x Receiver Collar (
2 in M86-2
)
1x Collar Strap (
2 in M86-2
)
2x Pair of Contacts (
4 in M86-2
)
2x Pair of Rubber Caps (4
in M86-2
)
1x Dual USB Charger
1x Test Light
Frequency: 433.825Mhz
Transmitter: 3.7V 500mAh LiPo
Receiver: 3.7V 500mAh LiPo
Contact:
support@petspystore.com
PetSpy Advanced Dog Training Collar
Operating guide for models M86-1, M86-2 (2 dogs), M86N
Note: PetSpy has 3 models of Advanced Dog Training Collars: M86-1 (gray), M86N
(black), and M86-2 (for 2 dogs). is manual is designed for all 3 models.
Visit
www.petspystore.com
to download this guide.
Copyright © 2015-2018 PetSpy Inc. All rights reserved.
Dear Customer, thank you very much for choosing the PetSpy Brand! It’s our
pleasure to serve you and your beloved dog. Our mission is to ensure your pet’s safety
and happiness by providing you with the tools and techniques to successfully train your
dog. If you have any questions, please contact PetSpy Customer Service at
support@petspystore.com -
we will be happy to assist you!
FUNCTIONS, BUTTONS AND LCD ICONS
1. Charging Port
2. Transmitter Tone Button/Level Up
3. Vibration Button
4. Menu/Mode Button
5. Shock Button
6. Receiver Tone Button/Level Down
•Receiver Tone Level: indicates 3 Levels of Tone.
•Shock Level: indicates 8 Levels of Shock.
•Battery Charge Indicator: indicates 3 Levels of Battery Charge.
•Vibration Level: indicates 8 Levels of Vibration.
•A - Receiver A is being Controlled; B - Receiver B is being Controlled.
•A&B - both Receivers are being Controlled.
Menu/Mode Button
- Press the button to change control between Receiver A, Receiv-
er B, or Both Receivers A&B. Press and hold the button for 3 seconds to enter/exit
Programming Mode. While in Programming Mode, press the button to conrm your
selected settings (e.g. Shock or Vibration Level) and go to another one.
Shock Button
- Press the button to deliver Shock Stimulation to your dog.
Vibration Button
- Press the button to deliver Vibration Stimulation to your dog.
Receiver Tone Button/Level Down
- Press the button to deliver Beeping Sound to your
dog. In the Programming Mode, the button is used to lower the stimulation level
(e.g. Shock).
Transmitter Tone Button/Level Up
- Press the button to produce tone in the Transmit-
ter. In the Programming Mode, the button is used to increase the stimulation level
(e.g. Shock).
FEATURES
1. 3 Training Modes: Shock, Vibration, and Sound.
2. Rechargeable Transmitter and Receiver - recharge time is about 2-3 hours.
3. Fully waterproof Receiver Collar.
4. e system communication range is up to 1100 yards (in ideal conditions).
5. Eight correction levels of Shock and Vibration Stimulation.
6. e system can be used with 1 or 2 collars. It gives you a simultaneous control of up
to 2 dogs.
7. Power Saving Design with auto sleep mode and remote collar activation.
8. Two pairs of metal contacts (short and long) for dogs with dierent hair length.
9. Two pairs of conductive rubber caps for added safety. ey were specically designed
to avoid skin irritation and injuries.
HOW DOES PETSPY DOG TRAINING SYSTEM WORK?
PetSpy Dog Training System can assist you with controlling and training your dog
without a leash in the range up to 1100 yards. Using a Remote Transmitter you can send
a signal to the collar in form of Shock, Vibration, or Tone. By using PetSpy Dog Training System consistently, you can train your dog to eliminate any undesired behavior
(jumping up, digging, chasing, etc.) and teach your dog understand many obedience
commands (sit, come, stay, etc).
IMPORTANT NOTES
•e Remote System range goes up to 1100 yards. Hold the Transmitter horizontally
and away from your body to achieve maximum range. Weather condition, terrain,
vegetation, and interference from other electronic devices can aect the maximum
communication distance of the system.
•ere are 8 levels of Shock and Vibration Simulation. If you use the strongest level
there is a chance that it can penetrate dog’s fur up to 6mm thick. Do not shave your
Dog’s neck to reduce the risk of skin irritation.
•For comfort, safety, and eectiveness of the system, please start training your pet with
the lowest level of Shock. It’s ne to have a Vibration level on medium or high. Please
check your dog’s neck aer each training session for skin irritation. If skin irritation develops, discontinue to use the collar for 48 hours. If condition persist beyond 48 hours,
please consult your veterinarian.
•Do not attach a leash to the collar. Use a separate collar if there is a need for a leash.
•We suggest you to use the Vibration Stimulation rst before starting to use the Shock
Stimulation. en slowly start with the lowest level of the Shock Stimulation. If you
follow this training method, your dog will learn that the Shock Stimulation will come
aer Vibration. Hence, the Vibration alone can eectively cure unwanted behavior of
your dog without a need for the Shock.
PREPARING REMOTE TRANSMITTER FOR YOUR FIRST USE
•Please charge the Remote Transmitter for approximately 2 hours.
•e Charging Port is located on top of the transmitter (next to antenna).
•During the charge, the Battery Indicator icon will be ashing. When the battery is fully
charged the indicator will turn solid, notifying you that the charging is completed.
REMOTE TRANSMITTER OPERATION
1. e remote always stays in the Stand-by Mode. Simply press any button to wake it up.
2. You can select which Receiver Collar is being controlled (A, B, or A&B) by pressing
the Menu/Mode Button.
3. Press the Vibration Button to deliver the Vibration Stimulation to your dog.
4. Press the Shock Button to deliver the Shock Stimulation to your dog.
5. Press the Receiver Tone Button to deliver beeping noise to your dog during the
Sound Training.
REMOTE TRANSMITTER PROGRAMMING
1. Press any button to make sure that Remote is on.
2. Press and Hold the Menu/Mode Button for 3 seconds until you hear a beep to enter
the Programming Mode. e Receiver to be programmed (A, B, or A&B) will start
ashing. If Receiver A is ashing, but you would like to program Receiver B or both Receivers A&B, simply use 2 Tone Buttons (upper le and upper right) to switch between
the Receivers.
3. When desired Receiver is selected to be programmed (A, B, or A&B), press Menu/
Mode Button to start setting it up. e setup process starts with the Receiver Tone
Level. Use 2 Tone Buttons (upper le and upper right) to adjust its Level and then press
Menu/Mode Button to conrm. Next, it will take you to the Vibration Intensity Level
setup, Shock Intensity Level setup, and nally to the Transmitter Tone Level setup.
4. When programming is complete, press and hold Menu/Mode button to save your
settings.
5. You can repeat Steps 2-4 to program Receiver A, Receiver B, or both Receivers A&B.
PREPARING RECEIVER COLLAR FOR YOUR FIRST USE:
Make sure that Receiver Collar is charged before proceeding to the training:
1. Carefully open the rubber cover over the charging port and connect the charger.
2. Red LED light will indicate that receiver is charging. It takes about 3 hours to fully
charge it. Make sure to unplug the collar aer 3 hours to avoid battery damage.
3. Put the rubber cover back over the charging port to ensure collar is fully waterproof.
4. Press the Power Button to turn it on. e red LED will start ashing every 4-5 seconds.
5. When Receiver is charged and turned on, it always stands in the Sleep/Standby Mode
waiting for any command (e.g. Shock, Vibration or Beep) to activate it.
SYNCHRONIZING REMOTE TRANSMITTER WITH RECEIVER COLLAR
Sometimes the collar can loose connection with remote. e x is pretty quick and
simple. Follow these steps to re-synchronize the system:
1. Make sure that both the Transmitter and Receiver are fully charged and turned on.
2. Press and hold the Power button on the Receiver Collar for about 5 seconds to enter
the Synchronization Mode - the receiver will beep and red LED will start ashing fast.
3. While red LED is ashing, send any correction command from remote. We recommend you to send a Vibration command by pressing and holding the Vibration button
on remote until you feel that collar vibrating. If no command is sent, the ashing will
stop aer 10 seconds.
4. e system is now resynchronized - try to send any command to test it.
If you have 2 collars, repeat the above steps for both collars A and B. Make sure to set
the Remote to mode A when synchronizing the rst collar, and then switch it to B to
synchronize the second collar.
TESTING PETSPY DOG TRAINING SYSTEM
Shock Test:
•Take the included Test Light and put its metal wire on the
Receiver’s Contact Points.
•Press the Shock Button on the Remote Transmitter.
•e Test Light will light up indicating that shock is working.
•e higher the shock level is the brighter it should be.
Vibration Test:
•Press the Vibration Button on the Remote Transmitter.
•e Receiver Collar will vibrate indicating that vibration stimulation is working.
•Try to adjust the level of vibration and see how the intensity is changing.
Receiver Tone Test:
•Press the Receiver Tone Button on the Remote Transmitter.
•e Receiver Collar will beep indicating that receiver tone is working.
FITTING THE COLLAR
To ensure eective training and dog’s safety, you must properly t the collar on your
dog. e collar must t snugly to allow the “contact points” to have direct contact with
the skin. Position the receiver unit high up on your dog’s neck just below ears.
You should be able to t two ngers between the collar strap and your dog’s skin. Too
tight poses the risk of skin irritation and discomfort. Too loose and the contact points
will not be able to administer the stimulation reliably and can cause skin irritation due
to chang. Cover the contact points with conductive rubber caps to reduce the risk of
skin irritation or injury.
CAUTION: E-collars are not designed to be worn constantly. We recommend using
e-collars only under adult supervision and for no longer than 4 hours per day. NEVER
attach a leash to an e-collar. Use a separate regular collar if there is a need for a leash.
Please refer to PetSpy Dog Training E-Book for more dog training tips.
You can download it at
www.petspystore.com
- it is free!
GENERAL TIPS
• PetSpy Dog Training Collar is not design to be worn constantly. We recommend you
to limit collar usage just for active Training Sessions. Always take o the collar when
you leave your dog unattended.
• Most dogs will feel uncomfortable when wearing collar for the rst time. Don’t use
any commands until your dog has gotten used to the collar which will normally take
several days.
• Eliminate one unwanted action or teach one obedience command at a time. If you
move to quickly with training, your dog may become confused.
• Be consistent in your training. Give your dog the same stimulation for each unwanted
action. We suggest you to use Vibration Stimulation before starting the Shock Stimulation. If you follow this training method, your dog will learn that Shock Stimulation
might come aer Vibration. Hence, the Vibration Stimulation alone can eectively cure
unwanted behavior of your dog.
• Do not over-correct. Use as few stimulation as possible to train your dog.
• Following a predened scenario in all Training Sessions can dramatically improve
your chances of success.
• Should your dog react to the training by hiding or reacting fearfully, redirect his attention to a simple command such as “Speak” or “Sit” to calm him down. Use treats to help
your dog understand which commands have been done correctly.
TROUBLESHOOTING
My e-collar does not respond to any command, what should i do?
•Make sure that both the Remote Transmitter and Receiver Collar are fully charged and
turned on. e red LED on the receiver should be ashing every 4-5 seconds.
•Follow the steps from “
Synchronizing Remote Transmitter with Receiver Collar”
para-
graph to pair remote transmitter with the collar.
•Watch our video guides for more information at
www.petspystore.com/video
•Contact us at
support@petspystore.com
if the above steps don’t help.
REGULAR MAINTENANCE AND STORAGE
•When not used, PetSpy Dog Training System must be kept in a dry place just like any
other electronic devices.
•To prevent batteries from damage, charge both the Transmitter and Receiver regularly
even when it’s not used. Make sure you do not charge it for longer than 3 hours.
•Clean the receiver and contact points weekly. Make sure that contact points are tightly
attached to the collar.
•Check your dog’s neck for irritation daily.
FREQUENTLY ASKED QUESTIONS
1. Is the Receiver Collar waterproof?
Yes, the Receiver Collar is fully waterproof.
2. Is the Remote Transmitter waterproof?
No, the Remote Transmitter must be kept away from water.
3. Once my dog is trained, do we have to continue using the collar?
You might have to reinforce training with the collar from time to time.
4. How long can I continuously deliver Vibration or Shock to my dog?
e max amount of time you can deliver the Vibration or Shock to you dog contin uously is 10 seconds. e remote transmitter will time out and the Vibration/Shock
button must be released and pressed again.
CAUTION: While it is ne to use the Vibration for up to 10 seconds, it is highly
recommended to limit the continuous Shock delivery to no more than 3 seconds (the
smaller the dog the shorter it should be).
5. What should I do if my dog’s neck becomes red and irritated?
Stop using the collar immediately for at least 48 hours. If the condition persists be yond 48 hour please consult your veterinarian.
6. Can I attach a leash to the Receiver collar?
No, this can result in pulling the contact points to tightly against your dog’s neck
causing an injury. Use a separate collar when needed.
7. How long can I leave a Receiver Collar on my dog?
E-collars are not designed to be worn constantly! We recommend to use it only
during active training sessions and outdoor activities for no longer than 4 hours per
day under adult supervision.
8. How long should the training sessions be?
Training sessions should be kept short and positive (10-15 minutes).
9. How long does the battery charge last?
It depends on the intensity of training sessions and vary from one day to one week.
10. What is the maximum operational range?
e max operational range is 1100 yards in ideal conditions. e range may vary
depending on the terrain, buildings, trees and electromagnetic interference.
11. Will the collar t my dog?
e collar strap is adjustable to t dogs from 10 to 140 pounds. It has a maximum
length of 26 inches and minimum length of 8.
12. What is the best dog’s age to start training?
Your pup should be old enough to understand basic commands. 6 months is nor mally a good age.
Should you have more questions, feel free to contact us at
support@petspystore.com
With PetSpy Advanced M86-2 Dog Training System you can train up to 2 dogs at the
same time using one Remote Transmitter. is is how it looks like on the LCD screen:
support@petspystore.com
Copyright © 2015-2018 PetSpy Inc. All rights reserved.
TERMS OF USE AND LIMITATION OF LIABILITY
1. Terms of Use
is Product is designed to be used with dogs where training is desired. e specic
temperament of your dog may not work with the product. We do not recommend you
to use this product if your dog is less than 10 lbs, under 6 months old, or if your pet
is aggressive. If you are unsure whether this is appropriate for your pet, please consult
your veterinarian, or a certied trainer. Proper use includes reviewing the entire User
Manual and Dog Training Guide provided with the product. Pay extra attention to all
Caution statements.
2. No Unlawful or Prohibited Use
is Product is designed for use with dogs only. PetSpy dog training collar is not
intended to harm, injure, or provoke. Using this product in a way that is not intended
could result in violation of Federal, State or local laws.
3. Limitation of Liability
In no event shall we be liable for any direct, indirect, punitive, incidental, special or
consequential damages and injuries, or any damages and injuries whatsoever arising
out of or connected with the use or misuse of this Product. Buyer assumes all risks and
liability from the use of this Product.
4. Modication of Terms and Conditions
We reserve the right to change the terms, conditions and notices under which this
Product is oered.
WARRANTY
Please register your 1-year replacement warranty at
www.petspystore.com/warranty
If your purchased e-collar malfunctions or breaks within 1 year, we will send you a free
replacement. No more than one replacement per purchased item. Replacement warranty does not apply to promotional orders with total discount greater than 30%. e warranty begins from the date of purchase. A purchase conrmation such as amazon order
id is required for a claim. e warranty does not cover products with physical damage
or lost items. PetSpy does not oer warranty for products purchased from unauthorized
resellers such as online auctions. PetSpy products are exclusively sold on Amazon.
com, Chewy.com and PetSpy.com. Any other sources are considered as unauthorized
resellers. e refund period is strictly limited to 30 days for all products starting from
the date of purchase.
Loading...