Read training manual and quick
guide before attempting to use
the product.
QUICK GUIDE
ULTRALIGHT SONIC
BARK CONTROL
STEP 1 BATTERY ACTIVATION
The battery module is installed in your UltraLight Sonic Bark
Control unit. A removable protective film on the contact side of
the battery prevents activation of the unit. Introduce your dog to
the bark control unit as described in the training manual before
removing the protective film.
To remove the battery,
insert a coin in the slot on
top of the battery module,
push down slightly and turn
counter-clockwise. Flip battery
to contact side. To remove the
protective film, lift the
red tab and peel off the film.
PG. 2
To re-install battery, align the arrow
on the battery module with the triangle
on the unit. Using a coin, push down
and turn clockwise, until the arrow on
the battery module lines up with the
"Lock" on the unit.
Battery life is dependent on the number of corrections your
dog receives, but on average the life should be 1 month.
STEP 2 TEST UNIT
Hold your finger over
the speaker to muffle
the sound when testing
the unit. Blow across
the microphone. The unit
should emit a sharp
sound. If you do not
hear a tone – check
the battery and repeat
the test.
STEP 3 SET MICROPHONE SENSITIVITY LEVEL
Locate the microphone High/
Low switch on the side of the
unit. Begin with the setting
in the low position. If the unit
does not emit a sound
correction when the dog barks,
move the switch to the high
setting.
PG. 3
microphone
speaker
STEP 4 AT
TACH TO COLLAR
Note: Do not place unit on your dog without reading the
Training Manual.
Collar material thickness
should be approximately
1/16", and no wider than
1". Slide the collar under all
four clips. Be sure the unit
is placed in the center of
the collar, opposite of the
buckle, and fits snuggly against
the middle of the dogʼs throat.
The microphone may not
activate properly if the unit
is rotated to the side or if
the collar hangs too loosely. Remove any tags from the collar to
avoid triggering a false stimulation.
STEP 5 OBSERVE FIRST REACTION
Observe your dog's first reaction to the correction. As
excited as your dog may get, you must remain calm. Yelping or
cowering is a normal response. Your pet must clearly understand
the reason for the stimulation in order to change his behavior.
Modifying your dogʼs barking behavior may take several days.
PG. 4
Each dog will need different lengths of time to learn to
control their nuisance barking.
CAUTIONS
To prevent damage to the inner ear, do not place the unit next to
your ear, the ear of any other human, or your petʼs ear.
Keep out of the reach of children.
Do not allow dog to chew on unit.
Unit is not waterproof - do not immerse in water.
If unit gets wet, you may remove battery, shake out excess
water, and let unit dry before attempting to use again.
ADDITIONAL INFORMATION
If you have additional questions regarding this product
or training, U.S. customers may contact PetSafe Customer
Support at 1-800-732-2677. The phones are staffed
Monday – Friday 8AM till 7PM, Saturdays 9AM till 5PM,
and Sundays 1PM till 5PM (Eastern Time).
PG. 5
Correspondence may be sent to the following address:
Radio Systems Corporation
10427 Electric Ave.
Knoxville, TN 37932
Other helpful information may be found on our website:
www.petsafe.net
RETURNS
If you are experiencing problems with your unit, our
customer support department may be able to offer helpful
advice. Should you decide to return your product, please include
a brief description of the problem and ship to: RSC, Service
Warehouse, 10427 Electric Ave., Knoxville, TN, 37932. You pay
the shipping charges to RSC. RSC pays the shipping charges
to return to you.
400-397/B
Loading...