Petsafe Anti-Bark Collar Operating And Training Manual
Anti-Bark Collar
Collier anti-aboiements
Halsband tegen blaffen
Operating and Training Guide
Manuel d’utilisation et de dressage
Handleiding en Africhtingsgids
Operating and Training Guide
Manuel d’utilisation et de dressage
Handleiding en Africhtingsgids
Please read this entire guide before beginning
Veuillez lire ce manuel en entier avant de commencer
Gelieve deze gids volledig door te lezen voordat u begint
2 www.petsafe.net
Thank you for choosing PetSafe®, the best selling brand of
electronic training solutions in the world. Our mission is to
ensure your pet’s safety by providing you the tools and techniques
to successfully train your pet. If you have any questions, please
contact the Customer Care Centre or visit our website at
www.petsafe.net.
____________________________________________________________________
Table of Contents
Components ........................................................................... 3
Features .................................................................................. 3
How the PetSafe Anti-Bark Collar Works .................................. 4
Key Defi nitions ....................................................................... 4
Fit the Anti-Bark Collar ........................................................... 5
To Insert and Remove the Battery ............................................ 7
Modes of Operation ................................................................ 8
What to Expect During Use of the Anti-Bark Collar ................. 9
Regular Maintenance .............................................................. 9
To Test the Anti-Bark Collar .................................................. 10
Accessories ........................................................................... 10
Frequently Asked Questions .................................................. 11
Troubleshooting .................................................................... 12
To Discharge the Anti-Bark Collar ......................................... 12
Terms of Use and Limitation of Liability ................................ 13
Français .............................................................................. 15
Nederlands .......................................................................... 28
____________________________________________________________________
“In a Tuskegee University study of adult shelter dogs wearing
the PetSafe Anti-Bark Collar for six 30-minute sessions over two
weeks, we detected no long-term adverse effects, and all dogs
dramatically reduced their barking by the second day.”
Dr. Janet Steiss and Dr. Caroline B. Schaffer
Tuskegee University
www.petsafe.net 3
Components
Operating Guide
Battery
(PetSafe
®
RFA-67)
Warranty
Card
Warranty
PetSafe Anti-Bark Collar
TE
ST
Features
• Tone Correction option
• Tone plus Static Correction options
• 3 Training Modes (up to 6 levels of Static Correction)
• Patented Perfect Bark™ technology for the most reliable bark detection
• Water Resistant
• Low Battery Indicator Light
• On/Off Switch
• Lifetime Limited Warranty
4 www.petsafe.net
How the PetSafe Anti-Bark Collar Works
• The Anti-Bark Collar has a unique patented sensor technique that provides the most
reliable bark detection available. The Anti-Bark Collar uses both vibration and sound
sensors to discriminate your dog’s bark from external noises.
• You choose whether your dog’s barking will be corrected with Tone only or with a
combination of Tone and harmless Static Correction.
• If the Tone only mode is your choice, each time your dog barks, he will hear a “Bad
Dog” Tone.
• If a mode for Tone and Static Correction is selected, a simultaneous Tone and Static
Correction will be administered through the Contact Points only when both the
vibration from the vocal cords and the sound from the bark match the bark sampling
criteria.
• This correction can be customised to your dog. Correction can be set to administer
4 corrections at the same level before increasing to a higher correction level (up
to Level 6), or may be set to increase in intensity every time your dog barks, to a
maximum of Level 6.
• As a built-in safety feature, if your dog barks 15 times or more within a 50 second
period, the Anti-Bark Collar will automatically shut off for 3 minutes.
Important:
• Before playing with your dog, remove the Anti-Bark Collar. The
activity may cause your dog to bark, which could lead to him
associating the play with the Static Correction.
• Never leave the Anti-Bark Collar on your dog for more than 12
consecutive hours.
____________________________________________________________________
Key Defi nitions
Indicator Light: Indicates that the Anti-Bark
Collar is functioning properly in the TEST Mode,
and when the battery is low.
Sound Activated Sensor: Detects the sound of
your dog’s bark.
Mode Switch: Adjusts the training mode. This
switch is also used to turn the Anti-Bark Collar off,
and for testing
Sensor Probe: Detects the vibrations of your dog’s
bark. Note: The Sensor Probe is not adjustable.
Contact Points: Deliver the safe Static
Correction.
Contact Points
Battery
Sensor
Probe
Mode
Switch
Indicator Light
Sound Activated
Sensor
test
off
www.petsafe.net 5
Fit the Anti-Bark Collar
Important: The proper fi t and placement of your Anti-Bark Collar is
important for effective operation. The Contact Points must have direct
contact with your dog’s skin on the underside of his neck.
To ensure a proper fi t, please follow these steps:
1. Make sure that the battery is not installed in the Anti-
Bark Collar.
2. Have your dog standing comfortably.
3. Centre the Contact Points underneath your dog’s neck,
touching the skin.
YES
NO
Note: It is sometimes necessary to trim the hair
around the Contact Points to make sure that contact
is consistent.
4. The PetSafe QuickFit™
Collar is designed so you
can quickly attach and
remove the Anti-Bark
Collar from your dog
while maintaining the
desired fi t.
a. With the Snap Buckle
fastened, thread the
collar through the
Metal Buckle.
b. Slide the excess collar through the “C” Loop on
top of the Snap Buckle. This will hold the collar in
place.
c. Once the collar fi t is determined, simply use the
Snap Buckle to remove and replace the collar.
5. The Anti-Bark Collar should fi t snugly, yet loose
enough to allow one fi nger to fi t between a Contact
Point and your dog’s neck. Allow your dog to wear the
collar for several minutes, then recheck the fi t. Check the fi t
again as your dog becomes more comfortable with the AntiBark Collar.
6. Trim the collar as follows:
a. Mark the desired length of the collar with a pen. Allow for
growth if your dog is young or grows a thick winter coat.
b. Remove the Anti-Bark Collar from your dog and cut off
excess.
Snap Buckle
“C” Loop
Metal Buckle
6 www.petsafe.net
Important: Do not attach a lead to the collar. This can
result in pulling the Contact Points too tightly against your
dog’s neck. Attach a lead to a separate, non-metallic collar
or harness, making sure the extra collar does not put
pressure on the Contact Points.
Important: For comfort, safety and effectiveness of product, please ensure
the following:
• Check the fi t to prevent excessive pressure by being able to insert one
fi nger between the Contact Point and your pet’s skin.
• Your pet must be carefully examined daily for any signs of a rash or sore.
• If a rash or sore is observed, discontinue the use of the Anti-Bark Collar
for a few days.
• If the condition persists beyond 48 hours, see your veterinarian.
• Your pet’s neck and the Contact Points must be washed weekly with a
wash cloth and mild hand soap, then rinsed thoroughly.
A condition called Pressure Necrosis, which is a devitalisation of the skin
due to excessive and prolonged contact against the Contact Points, may
occur if the steps above are not followed.
www.petsafe.net 7
To Insert and Remove the Battery
Note: Do not install the battery while the Anti-Bark Collar is on your dog.
This Anti-Bark Collar uses a replaceable PetSafe® battery (RFA-67). This
unique battery is designed to make battery replacement easier and increase
water protection.
To insert the battery, align the symbols
on the battery (arrow) and Anti-Bark
Collar (triangle). Use a large coin to
turn the battery clockwise until the
arrow lines up with the lock symbol on
the housing.
To remove the battery, turn the
battery counter-clockwise using a large
coin. DO NOT attempt to cut into
or pry open the battery. Be sure to
discard the used battery properly.
A replacement PetSafe® battery (RFA-67) can be found at many retailers.
Contact the Customer Care Centre or visit our web site at www.petsafe.net
to locate a retailer near you.
Battery Life
Average battery life is 2 to 4 months, depending on how often your dog barks.
However, due to your dog’s learning process, your fi rst battery may not last as
long as replacement batteries.
Indicator Light
The Indicator Light acts as a low battery indicator. While in a Correction Mode,
the light will fl ash once every 2 to 3 seconds to indicate a low battery. While in
TEST Mode, a low battery will cause the Indicator Light to turn on, and the
Anti-Bark Collar will not respond to testing until the battery is replaced.
8 www.petsafe.net
Modes of Operation
Turn to the OFF position when the AntiBark Collar is not in use to conserve battery
power.
Mode 1:
• The Anti-Bark Collar starts at Level 1
(Tone and Static Correction) and continues
to give a Level 1 correction each time your
dog barks within 30 seconds, to a maximum
of 4 times.
• If the dog continues to bark, the Anti-Bark
Collar will proceed to Level 2. After 4
consecutive barks at Level 2
test
off
1
2
3
Off
Test
within 30 seconds, the correction level will increase.
• The correction levels will continue to increase in this fashion up to Level 6.
• If the dog does not bark within 30 seconds of the previous bark, the Anti-Bark
Collar will reset itself to Level 1.
Note: All 6 levels of correction are a simultaneous Tone and Static Correction.
Mode 2:
The Anti-Bark Collar starts at Level 1 (Tone and Static Correction) and
increases to the next higher level (up to Level 6) each time your dog barks
within 30 seconds of the previous bark.
If your dog does not bark again within 30 seconds, the Anti-Bark Collar will
reset itself to Level 1
Mode 3:
The Anti-Bark Collar will deliver a Tone only, without Static Correction each
time your dog barks.
TEST:
Turn to the TEST Mode to verify that your Anti-Bark Collar is working
properly. Do not use this mode for normal operation. See “To Test the AntiBark Collar”
www.petsafe.net 9
What to Expect During Use of the Anti-Bark Collar
Important: Do not leave your dog alone the fi rst few times he receives a
Static Correction.
Step One: (Day 1-5) Start by putting the Anti-Bark Collar on Mode 1. Now
put your dog in the situation where it has barked in the past. This situation
should not be one where strangers arrive or enter your property. Upon
barking, the dog will receive Audible Tone and Static Corrections as he barks.
This should curb the behaviour quickly. If this training mode does not stop
your dog’s barking after one hour and excessive barking is still occurring,
switch the collar to Mode 2.
Step Two: (Day 6 and beyond) Your dog is now ready for the tone only mode
of the collar, which is Mode 3. In this mode, your pet will only receive audible
tone with no static correction. Your pet may need the occasional refresher
course if barking reappears. In this case, go back to step one and reintroduce
the static correction.
____________________________________________________________________
Regular Maintenance
• Check Contact Points for tightness weekly
Note: Do not adjust the factory preset Sensor Probe.
• Clean Contact Points with alcohol weekly
Note: Remove the battery and discharge the Anti-Bark
Collar before touching the Contact Points.
• Check your dog’s neck for irritation and wash neck
weekly.
10 www.petsafe.net
To Test the Anti-Bark Collar
Important: To avoid feeling the Static Correction yourself, never touch
the two Contact Points simultaneously.
1. Turn the Mode Switch to TEST.
2. Hold the unit by the collar with the Indicator Light
facing towards you. The unit should be within 15-25 cm
(6-10 in) of your mouth.
3. In order to trigger the unit, say “Test” loudly into the
Sound Activated Sensor.
4. The Indicator Light will fl ash three times to show that it
is functioning properly.
5. If the Indicator Light does not fl ash, ensure that the
OFF
TEST
LOW
BAT
test
off
TEST!
battery is properly installed, and/or replace the battery. If the Indicator Light
still does not fl ash, contact the Customer Care Centre or visit our website at
www.petsafe.net.
6. Return the Mode Switch to the training mode of your choice before
replacing the Anti-Bark Collar on your dog.
Note: The TEST Mode is not intended for normal operation. If the Anti-Bark Collar
is left in TEST Mode while on your dog, it can cause false correction and may reduce
battery life.
Accessories
To purchase additional accessories for your PetSafe Anti-Bark Collar, contact
the Customer Care Centre or visit our website at www.petsafe.net to locate a
retailer near you.
Component Part Number
Battery - two pack RFA-67D-11
www.petsafe.net 11
If the collar breaks, you do not have to replace the whole unit. The collar
is replaceable; however under normal circumstances there is no need to
separate the collar and receiver. Please contact the Customer Care Centre for
replacement collar and instructions.
Frequently Asked Questions
Will my dog stop
barking completely?
• The Anti-Bark Collar effectively and humanely
stops all barking when it is worn. It should only be
worn during periods of unwanted barking.
Will another dog’s
bark set off the AntiBark Collar?
• No.
Is the Anti-Bark Collar
safe and humane?
• Yes. The Anti-Bark Collar is designed to get your
dog’s attention, not to punish him. However, the
initial Static Correction may startle your dog.
Will the Anti-Bark
Collar work for my
dog?
• The Anti-Bark Collar is safe and effective for all
breeds and sizes of dogs, though it may be too large
for dogs under 3.6 kg (8 lb) to wear comfortably.
Can I attach a lead to
the Anti-Bark Collar?
• No. This can result in pulling the Contact Points too
tightly against your dog’s neck. Attach a lead to a
separate, non-metallic collar or harness, making sure
the extra collar does not put pressure on the Contact
Points.
12 www.petsafe.net
Troubleshooting
My dog keeps barking
(does not respond to
the Static Correction).
• Tighten the Anti-Bark Collar and/or trim your
dog’s hair where the Contact Points touch his
neck to ensure good skin contact.
• Test the Anti-Bark Collar (see “To Test the Anti-
Bark Collar” section).
• Increase the Training Mode.
• Replace the battery.
• Contact the Customer Care Centre or visit our
website at www.petsafe.net.
The Indicator Light
keeps fl ashing.
• Make sure the Mode Switch is not set to TEST.
• Replace the battery.
• If the light continues to fl ash with a new battery,
contact the Customer Care Centre.
To Discharge the Anti-Bark Collar
Important: Avoid touching the Contact Points unless the Anti-Bark
Collar is completely discharged.
After removing the battery, turn the Mode Switch to TEST. The unit will
discharge within 5 seconds.
www.petsafe.net 13
Terms of Use and Limitation of Liability
1. Terms of Use
This Product is offered to you conditioned upon your acceptance without modifi cation
of the terms, conditions and notices contained herein. Usage of this Product implies
acceptance of all such terms, conditions, and notices.
2.
Proper Use
This Product is designed for use with pets where training is desired. The specifi c
temperament of your pet may not work with this Product. We recommend that you do
not use this Product if your pet is less than 3.6 kg (8 lb) or if your pet is aggressive. If you
are unsure whether this is appropriate for your pet, please consult your veterinarian or
certifi ed trainer.
Proper use includes reviewing the entire Guide provided with your Product and any
specifi c Caution statements.
3.
No Unlawful or Prohibited Use
This Product is designed for use with pets only. This pet training device is not intended to
harm, injure or provoke. Using this Product in a way that is not intended could result in
violation of national or local laws.
4.
Limitation of Liability
In no event shall Radio Systems Corporation be liable for any direct, indirect, punitive,
incidental, special or consequential damages, or any damages whatsoever arising out of
or connected with the use or misuse of this Product. Buyer assumes all risks and liability
from the use of this Product.
5.
Modifi cation of Terms and Conditions
Radio Systems Corporation reserves the right to change the terms, conditions and notices
under which this Product is offered.
Compliance
This equipment has been tested and found to comply with relevant EU
Electromagnetic Compatibility, Low Voltage and R&TTE Directives. Before using
this equipment outside the EU countries, check with the relevant local R&TTE
authority. Unauthorised changes or modifi cations to the equipment that are not
approved by Radio Systems Corporation are in violation of EU R&TTE regulations,
could void the user’s authority to operate the equipment, and void the warranty.
14 www.petsafe.net
Important Recycling Advice
Please respect the Waste Electrical and Electronic Equipment regulations in your
country. This equipment must be recycled. If you no longer require this equipment,
do not place it in the normal municipal waste system. Please return it to where it
was purchased in order that it can be placed in our recycling system. If this is not
possible, please contact the Customer Care Centre for further information.
Product Warranty
Please register your product online at www.petsafe.net.
Loading...