PerTronix 44011 User Manual

HIGH PERFORMANCE COIL

INSTALLATION INSTRUCTIONS

HIGH PERFORMANCE COIL

INSTALLATION INSTRUCTIONS

* Legal in all 50 states and Canada

CARB E. O. #D-57-17

FLAME-THROWER III COIL APPLICATIONS

Use with:

Ignitor III 12V ALL 0.32 ohms 44011 45001 NA

Ignitor II Not Compatible

System

Voltage

Cylinders

Primary

Resistance

! Caution: Flame-Thrower III 0.32 coils should not be used with the (original)

Ignitor, Ignitor II or point type ignition system. Flame-Thrower III coils are only

compatible with Ignitor III ignition systems, and most Capacitive Discharge (CD)

systems that control the dwell period, or limit the current. (12volt negative ground

systems)

BALLAST RESISTOR or RESISTANCE WIRE

The ballast resistor needs to be removed if the Flame-Thrower III coil is used with the

Ignitor III, or any Capacitive Discharge (CD) system that controls dwell or limits the

current. This only applies to Ignitor III, or Capacitive Discharge systems.

1. To remove a ballast resistor (normally white ceramic blocks 3 to 4” inches long),

disconnect all wires on both ends of the ballast resistor. Remove the resistor from

the vehicle and splice the wires together at a single point.

2. To remove a resistance wire, trace the coil power wire, which was previously

connected to the positive coil terminal, back to the fuse block. Bypass this wire with

a 12-gauge copper stranded wire.

Recommended Flame-Thrower III

Coils

Black Chrome Epoxy

* Legal in all 50 states and Canada

CARB E. O. #D-57-17

FLAME-THROWER III COIL APPLICATIONS

Use with:

Ignitor III 12V ALL 0.32 ohms 44011 45001 NA

Ignitor II Not Compatible

System

Voltage

Cylinders

Primary

Resistance

! Caution: Flame-Thrower III 0.32 coils should not be used with the (original)

Ignitor, Ignitor II or point type ignition system. Flame-Thrower III coils are only

compatible with Ignitor III ignition systems, and most Capacitive Discharge (CD)

systems that control the dwell period, or limit the current. (12volt negative ground

systems)

BALLAST RESISTOR or RESISTANCE WIRE

The ballast resistor needs to be removed if the Flame-Thrower III coil is used with the

Ignitor III, or any Capacitive Discharge (CD) system that controls dwell or limits the

current. This only applies to Ignitor III, or Capacitive Discharge systems.

1. To remove a ballast resistor (normally white ceramic blocks 3 to 4” inches long),

disconnect all wires on both ends of the ballast resistor. Remove the resistor from

the vehicle and splice the wires together at a single point.

2. To remove a resistance wire, trace the coil power wire, which was previously

connected to the positive coil terminal, back to the fuse block. Bypass this wire with

a 12-gauge copper stranded wire.

Recommended Flame-Thrower III

Coils

Black Chrome Epoxy

If the vehicle has a ballast resistor or resistance wire, and is not equipped with

one of the systems mentioned above, the ballast resistor should not be removed.

09/13 0015-008705

If the vehicle has a ballast resistor or resistance wire, and is not equipped with

one of the systems mentioned above, the ballast resistor should not be removed.

09/13 0015-008705

FLAME-THROWER III COIL INSTALLATION

1. Make sure the ignition switch is off or disconnect the battery negative cable.

2. Remove the coil wire from the coil tower.

3. Remove all wires from the positive coil terminal.

4. Remove all wires from the negative coil terminal.

5. Loosen the coil clamp and remove the existing coil.

6. Install FlameThrower III coil into the coil clamp and tighten into place. Note: If

the Flame-Thrower III coil does not ﬁt properly in the existing coil clamp,

purchase PerTronix chrome clamp #10002 or zinc clamp #10001.

7. Connect the wires that were removed from the negative coil terminal of the old coil

to the negative terminal of the Flame-Thrower III coil.

8. Connect the wires that were removed from the positive coil terminal of the old coil

to the positive terminal of the Flame-Thrower III coil.

9. Push the coil wire into the coil tower making sure that the boot is secure around the

coil tower.

FLAME-THROWER III COIL INSTALLATION

1. Make sure the ignition switch is off or disconnect the battery negative cable.

2. Remove the coil wire from the coil tower.

3. Remove all wires from the positive coil terminal.

4. Remove all wires from the negative coil terminal.

5. Loosen the coil clamp and remove the existing coil.

6. Install FlameThrower III coil into the coil clamp and tighten into place. Note: If

the Flame-Thrower III coil does not ﬁt properly in the existing coil clamp,

purchase PerTronix chrome clamp #10002 or zinc clamp #10001.

7. Connect the wires that were removed from the negative coil terminal of the old coil

to the negative terminal of the Flame-Thrower III coil.

8. Connect the wires that were removed from the positive coil terminal of the old coil

to the positive terminal of the Flame-Thrower III coil.

9. Push the coil wire into the coil tower making sure that the boot is secure around the

coil tower.

PerTronix, Inc. warrants to the original Purchaser of its Flame-Thrower coils that

LIMITED WARRANTY

the product shall be free from defects in material and workmanship (normal wear and tear excluded) for a period of 90 days from the date of purchase. If within the period of the foregoing warranty PerTronix finds, after inspection, that the product or any component thereof is defective, PerTronix will, at its option, repair such products or component or replace them with identical or similar parts PROVIDED that within such period Purchaser:

1. Promptly notifies PerTronix, in writing, of such defects.

2. Delivers the defective product or component to PerTronix (Attn: Warranty) with proof of purchase date; and

3. Has installed and used the product in a normal and proper manner, consistent with PerTronix printed instructions THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE FURNISHING OF A REPAIR OR REPLACEMENT COMPONENT OR COMPONENTS SHALL CONSTITUTE THE SOLE REMEDY OF PURCHASER AND THE SOLE LIABILITY OF PerTronix WHETHER ON WARRANTY, CONTRACT OR FOR NEGLIGENCE, AND IN NO EVENT WILL PerTronix BE LIABLE FOR MONEY DAMAGES WHETHER DIRECT OR CONSEQUENTIAL.

440 East Arrow Highway

San Dimas, CA 91773

909-599-5955

www.pertronix.com

PerTronix, Inc. warrants to the original Purchaser of its Flame-Thrower coils that

LIMITED WARRANTY

the product shall be free from defects in material and workmanship (normal wear and tear excluded) for a period of 90 days from the date of purchase. If within the period of the foregoing warranty PerTronix finds, after inspection, that the product or any component thereof is defective, PerTronix will, at its option, repair such products or component or replace them with identical or similar parts PROVIDED that within such period Purchaser:

1. Promptly notifies PerTronix, in writing, of such defects.

2. Delivers the defective product or component to PerTronix (Attn: Warranty) with proof of purchase date; and

3. Has installed and used the product in a normal and proper manner, consistent with PerTronix printed instructions THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE FURNISHING OF A REPAIR OR REPLACEMENT COMPONENT OR COMPONENTS SHALL CONSTITUTE THE SOLE REMEDY OF PURCHASER AND THE SOLE LIABILITY OF PerTronix WHETHER ON WARRANTY, CONTRACT OR FOR NEGLIGENCE, AND IN NO EVENT WILL PerTronix BE LIABLE FOR MONEY DAMAGES WHETHER DIRECT OR CONSEQUENTIAL.

440 East Arrow Highway

San Dimas, CA 91773

909-599-5955

www.pertronix.com

Loading...