Perlick R24NB Installation Manual
INSTALLATION AND OPERATION INSTRUCTIONS
SINGLE DOOR REFRIGERATOR
MODEL NOS.
■■ R24N
■■ R24S
R24S
IMPORTANT INFORMATION
This manual has been prepared to assist you in the
installation of your Single Door Refrigerator and to
acquaint you with its operation and maintenance.
We dedicate considerable time to ensure that our
products provide the highest level of customer
satisfaction. If, however service is required, call
Perlick at 1-800-777-7267 or your dealer who can
provide you with a list of qualified service agents. For
your own protection, never return merchandise for
credit without our approval.
We thank you for selecting a Perlick product
and assure you of our continuing interest in
your satisfaction.
IMPORTANT WARRANTY INFORMATION
A Warranty card is enclosed that must be completed
and mailed to the Perlick Corporation in order to
register the warranty. If the card is not returned to
Perlick, the warranty period will begin from the date
the equipment is shipped from the factory.
R24N
Table of Contents
Cabinet Specifications ..........................................2
Installing
Uncrating and Inspection................................3
Plumbing.........................................................3
Electrical..........................................................3
Installing Shelves............................................3
Installing Casters or Legs ...............................3
Placing The Cabinet........................................3
Sealing the Floor.............................................4
Temperature Control .............................................4
Cleaning................................................................4
Cleaning Stainless Steel/Avoiding Corrosion .......4
Replacement Parts ............................................5/6
Wiring Diagram.....................................................7
Reversing the Doors.............................................8
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069
Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com
Form No. Z2288
Rev. 8.22.06
Installation and Operating Instructions
Single Door Refrigerator
NON-FINISHED TOP FINISHED TOP
MODEL NOS. DOOR FINISH DOOR FINISH
R24NB Black R24SB Black
R24NS Stainless Steel R24SS Stainless Steel
R24NG Glass w/ Black Trim R24SG Glass w/ Black Trim
R24NT Glass w/ Stainless Trim R24ST Glass w/ Stainless Trim
EXTERIOR: Back, top and sides are Galvanized steel. Top and sides are stainless steel.
Back is galvanized steel.
Both models: Front is stainless steel. Doors: Either black vinyl CRS or stainless steel.
Bottom: galvanized steel with stainless grille.
INTERIOR Both models: Interior liner is stainless steel. Includes two adjustable vinyl coated shelves plus
a bottom shelf.
CABINET Length 24” (610)
DIMENSIONS Depth 24
(mm) Height 34
INTERIOR CU. FT. (m3) 4.9 (0.14)
SHELVING Bottom floor shelf and two additional shelves included
CASE CAPACITY* 4.6
CONDENSING UNIT H.P. 1/6 HP
RUNNING LOAD –AMPS 2.3
Ship Wt. Lbs. (kg.) 145 (54)
ELECTRICAL 1 1 5V, 60Hz., 1 phase . Furnished with 3-prong, 6 foot rubber plug in cord.
PLUMBING None required. Moisture drains to self evaporating condensate pan in machinery compartment.
INSULATION 2” foamed-in-place polyurethane insulation.
TEMPERATURE RANGE Adjustable from 32°F to +42° F (0° to 6° C).
REFRIGERATION R-134A capillary tube-type. with hermetic condensing unit. Front access for condenser and cleaning.
VENTILATION Front vented.
OPTIONAL • Set of 4 casters (3
ACCESSORIES & • Set of 4 adjustable legs (6” - 7
* Capacity calculations based on use of 12oz. export bottles on standard shelving.
3
⁄4” high) P/N 65426.
1
⁄4” high) P/N 65423.
1
⁄4” (615)
1
⁄2” (887)
11 3/4”
[470]
5 9/16”
[141]
47 1/8”
[1197]
24”
[610]
180°
DOOR SWING
34 1/2”
[887]
3 11/16”
[92]
20”
[508]
8” [203]
8” [203]
8 7/16” [214]
30 9/16”
[776]
29 1/4”
[743]
Top View Front View End View
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
2
24 1/4”
[615]
18 1/2”
[470]
25 3/4”
[654]
FINISHED
STAINLESS
TOP
NON-FINISHED
TOP
Form No. Z2288
Rev. 8.22.06
Preparing the Cabinet – Single Door Refrigerator
Uncrating and Inspection
Remove all crating material before operating.
Carefully inspect cabinet for hidden damage.
If damage is discovered, file your claim immediately
with the transport company. Perlick is not
responsible for damage in transit.
Plumbing
No plumbing connections are required. Condensate
from the cooling coil is automatically evaporated
through a condensate pan located in the
condensing unit section.
Electrical
The cabinet must be connected to a separately
fused power source (see Electrical Specification
Plate) and grounded in accordance with National
and Local Electrical Codes.
CAUTION: Do not attempt to operate the equipment
on any other power source than that listed on the
Electrical Specification Plate.
Anti-tip (without Legs or casters)
To prevent the cabinet from tipping forward and to
provide a stable installation, the cabinet must be
secured in place with an anti-tip device.
A set of metal anti-tip brackets and installation
screws (#10brackets should be attached to the floor, at the
back of the cabinet; each bracket located to catch
each rear leveling leg when the cabinet is pushed
backward into position.
THE ANTI-TIP BRACKETS MUST CATCH EACH
OF THE LEVELING LEGS TO HAVE ASTABLE
AND SAFE INSTALLATION.
Some installation sites might need to be modified to
provide a secure surface for attaching the bracket.
Refer to the illustration below for anti-tip mounting
bracket locations.
NOTE: Do not extend leveler leg
more than 3/4” out of base. Do not
shim or pad to obtain levelness.
3
” wood screws) are supplied. These
⁄4
Ø 3/8”
Surface
mounts
to floor.
Placing the Cabinet
To assure maximum performance, fresh air must
be allowed to circulate through the machinery
compartment. Do not place anything in front of the
cabinet that would obstruct air flow at these grilles.
Do not place the unit in an unventilated small room.
Cabinet should be leveled front to back and side
to side.
Installing Casters or Legs (optional)
Attach casters or legs to the mounting bracket with
lockwashers and
Attach bracket and leg/caster assembly to the side
of the cabinet base using the
tapping machine screws provided.
1
⁄4”–20 hex head nuts provided.
1
⁄4”–20 hex head self-
7/16”
1 1/2”
20 7/8”
Cabinet must
have at least
5/16” clearance
from floor to
accomodate
brackets.
Shown with leg
leveler engaged
in anti-tip bracket.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
3
Form No. Z2288
Rev. 8.22.06
Loading...