Perlick F24NB, F24N, F24S, F24SB, F24NS Installation And Operation Instructions Manual
...
INSTALLATION AND OPERATION INSTRUCTIONS
SINGLE DOOR FREEZER
MODEL NOS.
F24N
F24S
Finished Stainless
Steel Top
F24S
IMPORTANT INFORMATION
This manual has been prepared to assist you in
the installation of your Single Door Freezer and to
acquaint you with its operation and maintenance.
We dedicate considerable time to ensure that our
products provide the highest level of customer
satisfaction. If, however service is required, call
Perlick at 1-800-777-7267 or your dealer who can
provide you with a list of qualified service agents.
For your own protection, never return merchandise
for credit without our approval.
We thank you for selecting a Perlick product
and assure you of our continuing interest in
your satisfaction.
IMPORTANT WARRANTY INFORMATION
To register your product, visit our web site at
(www.perlick.com). Click on “Commercial”, then
“Service”. You will see the link to “Warranty
Registration Form”. You must complete and submit
this form or the installation date will revert back to
the ship Date.
Non-Finished
Top
F24N
Table of Contents
Cabinet Specifications .........................................2
Installing
Uncrating and Inspection ...............................
Plumbing ........................................................ 3
Electrical ......................................................... 3
Placing The Cabinet ....................................... 3
Installing Casters or Legs ...............................
Anti-Tip ........................................................... 3
Sealing the Floor ............................................ 3
Defrost System ..................................................... 4
Temperature Control ............................................. 4
Cleaning the Condenser ...................................... 4
Cleaning the Cabinet ............................................ 4
Cleaning Stainless Steel/Avoiding Corrosion ....4/5
Wiring Diagram ..................................................... 5
Replacement Parts ............................................ 6/7
Reversing the Door .............................................. 8
3
3
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069
Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com
Form No. Z2255
Rev. 01.04.09
Sizes and Specifications
24”
[610]
8” [203]
8” [203]
8 7/16” [214]
34 1/2”
[887]
3 11/16”
[92]
30 9/16”
[776]
29 1/4”
[743]
NON-FINISHED
TOP
FINISHED
STAINLESS
TOP
5 9/16”
[141]
18 1/2”
[470]
24 1/4”
[615]
47 1/8”
[1197]
11 3/4”
[470]
20”
[508]
180n
DOOR SWING
Single Door Freezer
MODEL NOS. F24NB F24SB
F24NS F24SS
CABINET Length 24” (610) 24” (610)
DIMENSIONS Depth 24 1⁄4” (615) 24 1⁄4” (615)
(mm) Height 34
INTERIOR CU. FT. (
m3) 4.9 (0.14) 4.9 (0.14)
GLASS CAPACITY* 86 86
CONDENSING UNIT H.P. 1/5 HP 1/5HP
RUNNING LOAD –AMPS 2.0 2.0
Ship Wt. Lbs. (kg.) 145 (54) 145 (54)
INTERIOR
Both models: Interior liner is stainless steel. Includes two adjustable vinyl coated shelves plus
a bottom rack.
EXTERIOR: Back, top and sides are Galvanized steel. Top and sides are stainless steel.
Back is galvanized steel.
Both models: Front is stainless steel. Doors: Either black vinyl CRS or stainless steel.
Bottom: galvanized steel with stainless grille.
REFRIGERATION R-134A capillary tube-type. with hermetic condensing unit. Front access for condenser and cleaning.
ELECTRICAL 115V, 60Hz., 1 phase . Furnished with 3-prong, 6 foot rubber plug in cord.
PLUMBING None required. Moisture drains to self evaporating condensate pan in machinery compartment.
INSULATION 2” foamed-in-place polyurethane insulation.
TEMPERATURE RANGE Adjustable from -10° to +10° F (-23° to-12° C).
VENTILATION Front vented.
DEFROST SYSTEM Solid state, push button defrost system, manually initiated at end of each day, automatically
terminates after six hours. Hot gas automatic defrost every 4 hours for approximately 20 minutes
(time/temperature terminated).
OPTIONAL • Set of 4 casters (3
ACCESSORIES & • Set of 4 adjustable legs (6” - 7
* Capacity calculations based on use of 3” diameter glasses on standard shelving.
1
⁄2” (887) 34 1⁄2” (887)
3
⁄4” high) P/N 65426.
1
⁄4” high) P/N 65423.
TopView Front View End View
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
2
Form No. Z2255
Rev. 01.04.09
Preparing the Cabinet – Single Door Freezer
1 1/2”
20 7/8”
Cabinet must
have at least
5/16” clearance
from floor to
accomodate
brackets.
NOTE: Do not extend leveler leg
more than 3/4” out of base. Do not
shim or pad to obtain levelness.
Shown with leg
leveler engaged
in anti-tip bracket.
Surface
mounts
to floor.
Ø 3/8”
7/16”
TOP VIEW
BEAD SILICON
SEALER (RTV)
FLOOR
CABINET
Uncrating and Inspection
Remove all crating material before operating.
Carefully inspect cabinet for hidden damage. If
damage is discovered, file your claim immediately
with the transport company. Perlick is not
responsible for damage in transit.
Plumbing
No plumbing connections are required. Condensate
from the cooling coil is automatically evaporated
through a condensate pan located in the
condensing unit section.
Electrical
The cabinet must be connected to a separately
fused power source (see Electrical Specification
Plate) and grounded in accordance with National
and Local Electrical Codes.
CAUTION: Do not attempt to operate the equipment on any other power source than that listed on
the Electrical Specification Plate.
THE ANTI-TIP BRACKETS MUST CATCH EACH
OF THE LEVELING LEGS TO HAVE A STABLE AND
SAFE INSTALLATION.
Some installation sites might need to be modified
to provide a secure surface for attaching the bracket. Refer to the illustration below for anti-tip mounting bracket locations.
Placing the Cabinet
To assure maximum performance, fresh air must
be allowed to circulate through the machinery
compartment. Do not place anything in front of the
cabinet that would obstruct air flow at these grilles.
Do not place the unit in an unventilated small room.
Cabinet should be leveled front to back and side
to side.
Installing Casters or Legs (optional)
Attach casters or legs to the mounting bracket
with the lockwashers and 1⁄4”–20 hex head nuts
provided. Attach bracket and leg/caster assembly
to the side of the cabinet base using the 1⁄4”–20 hex
head self-tapping machine screws provided.
Anti-tip (without Legs or Casters)
To prevent the cabinet from tipping forward and to
provide a stable installation, the cabinet must be
secured in place with an anti-tip device.
A set of metal anti-tip brackets and installation
screws (#10-3⁄4” wood screws) are supplied. These
brackets should be attached to the floor, at the
back of the cabinet; each bracket located to catch
each rear leveling leg when the cabinet is pushed
backward into position.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Sealing the Cabinet
For sanitation purposes, it may be necessary to
seal the base of the cabinet to the floor. This can
be accomplished by laying a bead of silicone sealant between the base of the cabinet and the floor
as shown by the figure below.
When sealing the cabinet to the floor, make sure
that the louvered front grille plate can still be
removed for condenser maintenance and cleaning.
3
Form No. Z2255
Rev. 01.04.09
Loading...