Installation
Instructions
Dispensing Towers
Draft Arm, Lucky, Panther or Tee Towers
Draft Arm
Panther Tower
Lucky Tower
Tee Tower
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
Form No. Z2351
Rev. 04.17.19
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
TABLE OF CONTENTS
Beer and Wine Kits ............................................................................................................................................................................... 3
Tools and Materials Required ......................................................................................................................................................... 3
Dispensing Kit Component Parts .................................................................................................................................................. 3
Air Scoops for Field Retrot Kits ................................................................................................................................................... 7
General Installation and Field Retrot Installation ............................................................................................................. 8
Safety Information ............................................................................................................................................................................... 8
About Wine Dispensing ..................................................................................................................................................................... 8
Air Distributor and Air Scoop Installation - Field Retrot Instructions ...................................................................... 9
Air Tubing to Air Scoop Attachment ............................................................................................................................................ 9
Air Distributor Assembly Attachment to Cabinet .................................................................................................................... 9
Draft Arm and Tee Tower Instructions ..................................................................................................................................... 10
Draft Arm Preparation .................................................................................................................................................................... 10
Tee Tower Preparation .................................................................................................................................................................... 10
Mounting Draft Arms or Tee Towers to a Cabinet Top ........................................................................................................ 10
Mounting Draft Arms or Tee Towers to a Counter Top ....................................................................................................... 11
Attaching Faucets to Draft Arms or Tee Towers .................................................................................................................... 11
Mounting the Beer/Wine Drainer to a Cabinet Top ............................................................................................................. 11
Mounting the Beer/Wine Drainer to a Counter Top ............................................................................................................ 12
Running the Air Scoop Tubing to the Draft Arms or Tee Towers .................................................................................... 12
Attaching the Beer Line to the Draft Arms or Tee Towers ................................................................................................. 13
Attaching the Wine Line to Draft Arms or Tee, Lucky or Panther Towers .................................................................... 13
Attaching the Gas Line Tubing ................................................................................................................................................... 14
Attaching the Tapping Hole Covers .......................................................................................................................................... 14
Attaching the Air Distributor Cover ........................................................................................................................................... 14
Checking the System for Leaks ................................................................................................................................................... 14
Lucky and Panther Tower Instructions ................................................................................................................................... 15
Lucky and Panther Tower Preparation ..................................................................................................................................... 15
Mounting Lucky or Panther Towers to a Cabinet Top ......................................................................................................... 15
Mounting Lucky or Panther Towers to a Counter Top ........................................................................................................ 15
Attaching Faucets to Lucky or Panther Towers ..................................................................................................................... 15
Mounting the Beer/Wine Drainer to a Cabinet Top ............................................................................................................ 16
Mounting the Beer/Wine Drainer to a Counter Top ............................................................................................................ 17
Running the Air Scoop Tubing to the Lucky or Panther Towers ..................................................................................... 17
Attaching the Beer Line to the Lucky or Panther Towers .................................................................................................. 18
Attaching the Gas Line Tubing .................................................................................................................................................... 18
Attaching the Tapping Hole Covers .......................................................................................................................................... 18
Attaching the Air Distributor Cover .......................................................................................................................................... 19
Checking the System for Leaks ................................................................................................................................................... 19
Appendix ............................................................................................................................................................................................... 20
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
2
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
Please follow these instructions to ensure proper installation of Perlick beer and wine dispensing towers. These
instructions cover 3” Draft Arms and Tee, Lucky and Panther Towers. These instructions apply to the following beer and
wine dispensing kits:
Beer Kits
69526-1DA 69526-1DATF 69526-2DA 69526-2DATF 69526-3DA 69526-3DATF
69526-2TT 69526-2TTTF 69526-3TT 69526-3TTTF 69526-4TT 69526-4TTTF
69526-5TT 69526-5TTTF 69526-6TT 69526-6TTTF 69526-2N 69526-2NTF
69526-1L 69526-1LG 69526-2L 69526-2LG 69526-3P 69526-3PG
67945-2DA 67945-2TT 67945-4TT 67945-2L
Wine Kits
69526W-1DA 69526W-2DA 69526W-3DA 69526W-2TT 69526W-3TT
69526W-4TT 69526W-5TT 69526W-1L 69526W-2L 69526W-3P
67945W-2DA 67945W-2TT 67945W-4TT 67945W-2L
For eld installation, add a –R to the factory kit part number.
Note: Each kit contains enough hardware to install up to six product lines. Depending on how many lines you are
installing, you may have parts left over after the installation is complete.
Tools and Materials Required
- Safety glasses
- Rubber gloves
- Utility knife or vinyl tubing cutter
- Slotted screwdriver
- 1/4” nut driver (optional)
- 6” or 8” adjustable wrench
- Cordless drill driver
- 5/16” socket head driver bit
Dispensing Kit Component Parts
- Draft Arm, Tee Tower, Lucky or Panther Tower
Draft Arm Tee Tower Lucky (shown)
or Panther Tower
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
3
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
Dispensing Kit Component Parts, Continued
- Air Distributor Cover 68678-1
- DZS36 Air Distributor Cover 68779-1
- Gas/CO2 Tubing C23975-1
- Beer Line Connector 532
- Wine Line Connector 67750
- Anti-Microbial Drain Tubing 1390D
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
4
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
Dispensing Kit Component Parts, Continued
- Faucet Head Assembly 408X
- Stainless Steel Wine Faucet Head 408XSS
- Silicone Sealant C15997
- Drain Pan C18640A
- DZS36 Drip Tray 68819
- Waste Bottle - Wine C24392-1
- Waste Bottle Holder - Wine 68693-1
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
5
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
Dispensing Kit Component Parts, Continued
- Tapping Parts Kit 67305
- Tapping Parts Kit - Wine 67305W
- PVC Pipe 67562
- Parts Bag 67835
- Stainless Steel Wine Keg Coupler 67747
- Tapping Cover 67852-1
- Gasket 57355-1
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
6
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
Air Scoops for Field Retrot Kits (-R) only - see page 9.
- Air Scoop 69315-1
For BBR/BBRN/PTR
- Air Scoop 68686-2
For DZS60
- Air Scoop 68778-1
For PTS
- Air Scoop 68685-1
For BBS/BBSN
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
7
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
General Installation and Field Retrot Installation
Cabinets ordered with a dispensing kit from the factory will already have the air distributor and air scoop installed.
If you are doing a eld retrot on a previously installed cabinet, your kit also will include an air distributor and an air
scoop. Please refer to the Air Distributor and Air Scoop Installation - Field Retrot Instructions section on the following
page to install these components. Note that eld retrot kits will have a “-R” at the end of the kit model number.
Beer/Wine System Safety
WARNING - Any compressed gas such as CO2 can be dangerous! It is important that reputable
companies are used to supply and install systems and to thoroughly train all sta who will use
the system.
NEVER Connect a pressurized gas cylinder unless there are at least two safety mechanisms in the pressure system.
At least one at the regulator and one at the product container coupler.
NEVER Connect a pressurized gas cylinder directly to a keg.
NEVER Connect your own equipment to the pressure system.
ALWAYS Report any damage or leaks and have them repaired immediately.
ALWAYS Store gas cylinders in the upright position.
ALWAYS Ventilate after a gas leak.
ALWAYS Keep gas cylinders away from heat and preferably stored in a cooler part of the establishment.
ALWAYS Thoroughly train all sta who use the equipment.
About Wine Dispensing
Perlick oers the industry’s most complete line of commercial refrigerated wine storage
and serving equipment. Perlick’s WINEcertied family of products, specied in the
Dispensing Kit Component Parts section of this document, are manufactured specically
to properly store and dispense wine.
Wine components include a sanitary 304 stainless steel faucet, shank, union and keg
coupler with a sanitary 304 stainless steel probe, as well as avor-lock tubing, all to
protect the delicate avors of wines.
To preserve the integrity of Perlick WINEcertied wine products and systems, DO NOT use beer kit components
in wine systems.
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
8
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
AIR DISTRIBUTOR AND AIR SCOOP INSTALLATION - FIELD RETROFIT INSTRUCTIONS
Air Tubing to Air Scoop Attachment
1. Select the appropriate air scoop for the cabinet model being
retrotted. Air scoop photos with the cabinet models they apply to are
shown on page 7.
2. Knock out the desired slug from the air scoop and insert the 1” snap
bushing.
2 2
3. Secure the air tube in place by attaching a cable tie on each side of
the snap ring.
4. Mount the air scoop assembly against the air discharge plenum of
the evaporator.
5. Please refer to Diagram 5 in the Appendix for a drawing of the air
scoop used on the BBS, BBSN, and PTS Models.
3
PTS Series
Air Distributor Assembly Attachment to Cabinet
3
DZS60
BBS/BBSN BBR/BBRN/PTR
1
1. Place the air distributor cover bracket behind the air
distributor assembly and mount it to the desired location on
the cabinet wall. (Two-line assembly shown.)
1
9
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
DRAFT ARM AND TEE TOWER INSTRUCTIONS
Draft Arm Preparation
Remove backing from foam gasket #57355-1. Attach the gasket to the bottom ange of the
draft arm, ensuring the four mounting holes are aligned.
Tee Tower Preparation
There is no preparation needed for Tee Tower style dispensing heads.
Mounting Draft Arms or Tee Towers to a Cabinet Top
Note: If you are mounting the tower to a counter top instead of the cabinet top, please refer to the section titled
Mounting Draft Arms or Tee Towers to a Counter Top on the following page.
1. Most cabinets come with pre-drilled hole congurations in the cabinet top for mounting
dispensing towers and drainers. However, if the holes need to be drilled during eld installation, templates are available at www.perlick.com/bar-beverage-equipment/specications-
downloads/tower-and-drip-pan-templates/.
2. Factory-provided tapping holes will have a wood block embedded in the cabinet top for
additional support. It is recommended that you drill 3/32” pilot holes into the wood block for
the four mounting holes on the tower ange. Remove the protective lm paper from the area
1
where the tower will be installed.
3. Attach the dispensing tower to the cabinet top using a athead screwdriver. To prevent
accidental scratches or gouges, cover the tower ange and cabinet top while mounting the
tower. The tower should be sealed to the cabinet top with a food grade RTV silicone.
3
Mounting Draft Arms or Tee Towers to a Counter Top
1. A PVC tube, (Part #67562), is included in the tapping kit. This will be used as an air shaft when mounting to a
counter top. Please refer to Diagram 7 in the Appendix for detail on how to mount a Draft Arm or Tee Tower to a
counter top. The tower should be sealed to the cabinet top with a food grade RTV silicone.
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
10
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
DRAFT ARM AND TEE TOWER INSTRUCTIONS, Continued
Attaching Faucets to Draft Arms or Tee Towers
1. Align splines on faucet to nut on faucet head. Orient faucet so it is
perpendicular to the cabinet top. Hand tighten.
2. Using the spanner wrench provided, snug faucet tight. Do not overtighten.
1 2
Mounting the Beer/Wine Drainer to a Cabinet Top
Note: If you are mounting the drainer to a counter top instead of the cabinet top please refer to the section titled
Mounting the Beer/Wine Drainer to a Counter Top.
1. Slide the threaded drainer nipple through
cabinet top hole. On the underside of the
cabinet top, tighten the drainer using the
plastic nut. Take caution not to over-tighten.
2. Attach the nylon reducing bushing to the
drainer until hand tight.
3. Attach the nylon elbow to the reducing
1 2
4
the cabinet ends as other options for exiting the cabinet.
6
3
4. Slide the 1/2” ID anti-microbial drain tubing over the barbed end of
the nylon elbow.
5. Use the nylon hose clips and self-drilling screws to secure the drain
tubing to the cabinet walls. Ensure the tubing will be out of the way of
loading and unloading kegs.
6. Route the anti-microbial tubing to the beer/wine collection drain
or waste container. It may be routed to the oor drain located in the
right rear corner of the cabinet. The cabinet oor drain must then be
plumbed to an external drain. There are also knockouts provided on
7. Wine dispensing kits also include a polyethylene waste bottle as an
optional method to collect wine waste. The waste bottle holder is hung
over the rim of a keg and the waste bottle is snapped into the holder.
8. Apply a bead of silicone around the perimeter of the drainer.
bushing.
7
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
8
11
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
DRAFT ARM AND TEE TOWER INSTRUCTIONS, Continued
Mounting the Beer/Wine Drainer to a Counter Top
Note: If you are mounting the drainer to the cabinet top instead of a counter top, please refer to the section titled
Mounting the Beer/Wine Drainer to a Cabinet Top.
1. Slide the 1/2” ID anti-microbial drain tubing over the end of drainer
nipple. Feed the drain tubing through the drainer hole of the counter
top and the cabinet top.
2. Use the nylon hose clips and self-drilling screws to secure the drain
tubing to the cabinet walls. Ensure the tubing will be out of the way of
loading and unloading kegs.
1
3
2
3. Route the anti-microbial tubing to the beer/wine collection drain or
waste container. It may be routed to the oor drain located in the right
rear corner of the cabinet. It must then be plumbed to an external
drain. There are also knockouts provided on the cabinet ends as other
options for exiting the cabinet.
4. Wine dispensing kits also include a polyethylene waste bottle as an
optional method to collect wine waste. The waste bottle holder is hung
4
5. Apply a bead of silicone around the perimeter of the drainer. This will provide a seal as well
as hold it in position.
over the rim of a keg and the waste bottle is snapped into the holder.
5
Running the Air Scoop Tubing to the Draft Arms or Tee Towers
1. Trim the black corrugated tubing from the air scoop so the tube is
inserted approximately halfway into the dispensing head.
2. Use the mountable cable tie and a self-drilling screw to hold the
black air tube out of the way of keg loading and unloading.
1 2
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
12
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
DRAFT ARM AND TEE TOWER INSTRUCTIONS, Continued
Attaching the Beer Line to the Draft Arms or Tee Towers
1. Insert rubber washer into end of beer line
connector and attach to the beer tting on the
Draft Arm tower. Tighten with an adjustable
wrench but do not over-tighten.
2. Insert rubber washer into the other end
of the beer line and attach to keg coupler.
Tighten with an adjustable wrench but do not
1
1 2
Attaching the Wine Line to Draft Arms or Tee, Lucky or Panther Towers
over-tighten.
3. Repeat for each additional supply tubes.
1. Push the avor lock barrier tubing over the
barbed connection on the wine tower and
secure it with a clench style clamp.
2. Insert a rubber washer into the other end
of the avor lock barrier tubing and attach it
to the keg coupler. Tighten with an adjustable
wrench, but do not over-tighten.
1 2 2
Note: Keg couplers supplied with the wine tapping kit have 300 series stainless steel components to protect the
delicate avors of wine.
3. Repeat for each additional supply tube.
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
13
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
DRAFT ARM AND TEE TOWER INSTRUCTIONS, Continued
Attaching the Gas Line Tubing
1. Attach one end of gas line to a valve on the air distributor manifold
and tighten with a hose clamp, using a 1/4” nut driver.
2. Repeat for each additional product line.
3. Attach the other end of the gas line to the keg coupler and tighten
with a hose clamp, using a 1/4” nut driver.
1 3
Attaching the Tapping Hole Covers
1. To comply with NSF standards, please attach the tapping hole covers provided.
2. The two piece cover can be adjusted to tighten snugly around beer lines and air scoop
tubing.
3. Position covers tightly around tubing and mount to the bottom side of the cabinet top
using a cordless drill with a 5/16” socket head bit and the self-drilling screws provided. Please
refer to Diagram 3 in the Appendix.
1
Attaching the Air Distributor Cover
1. To comply with NSF standards, the air distributor cover should be installed. It easily can be
removed to access the valves on the air distributor.
2. Each end of the cover has a knockout to provide clearance for the gas line. Remove the
appropriate knockout.
3. Route the gas line through the side of the cover and hang the cover on the air distributor
bracket. Please refer to Diagram 4 in the Appendix.
1
Checking the System for Leaks
1. It is important to ensure the entire system is leak free.
2. The system can be checked by doing a pressure decay test or by tapping the system and inspecting for product
leaks and checking for gas leaks with soap and bubbles. Repair any leaks immediately.
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
14
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
LUCKY AND PANTHER TOWER INSTRUCTIONS
Lucky and Panther Tower Preparation
1. Cut the plastic cable tie and remove the hose clamp.
2. Remove the plastic jam nut, mounting nut, at washer, and second jam nut. Do not remove
the rubber ange gasket.
Mounting Lucky or Panther Towers to a Cabinet Top
Note: If you are mounting the tower to a counter top instead of the cabinet top please refer to the section titled
Mounting Towers Lucky or Panther Towers to a Counter Top.
1. Most cabinets come with pre-drilled hole congurations in the
cabinet top for mounting dispense towers and drainers. However, if
the holes need to be drilled during eld installation, templates are
available at http://www.perlick.com/bar-beverage-equipment/
specications-downloads/tower-and-drip-pan-templates/.
2. Insert the threaded mounting shaft through the hole in the cabinet
top. On the underside of the cabinet top place large at washer over
2 2
threaded shaft and tighten tower down using plastic nut. Take
caution not to over-tighten nut. You will not use either of the jam nuts
for the installation. The tower should be sealed to the cabinet top with
a food grade RTV silicone.
Mounting Lucky or Panther Towers to the Counter Top
1. Please refer to Diagram 8 in the Appendix for a detailed drawing on how to mount Lucky or Panther towers to a
counter top. The tower should be sealed to the counter top with a food grade RTV silicone.
Attaching Faucets to Lucky or Panther Towers
1. Align splines on faucet to nut on faucet head. Orient faucet so it is
perpendicular to the cabinet top. Hand tighten.
2. Using the spanner wrench provided, snug faucet tight. Do not overtighten.
1 2
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
15
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
LUCKY AND PANTHER TOWER INSTRUCTIONS, Continued
Mounting the Beer/Wine Drainer to a Cabinet Top
Note: If you are mounting the drainer to a counter top instead of the cabinet top, please refer to the section titled
Mounting the Beer/Wine Drainer to a Counter Top.
1. Slide the threaded drainer nipple through
the cabinet top hole. On the underside of the
cabinet top, tighten down the drainer using
the plastic nut. Take caution not to over-tighten.
2. Attach the nylon reducing bushing to the
drainer until hand tight.
1
3 4
5 6
1
2
3. Attach the nylon elbow to the reducing bushing.
4. Slide the 1/2” ID anti-microbial drain tubing over the barbed end of
the nylon elbow.
5. Use the nylon hose clips and self-drilling screws to secure the drain
tubing to the cabinet walls. Ensure the tubing will be out of the way of
loading and unloading kegs.
6. Route the anti-microbial tubing to the beer/wine collection drain
or waste container. It may be routed to the oor drain located in the
right rear corner of the cabinet. The cabinet oor drain must then be
plumbed to an external drain. There are also knockouts provided on
the cabinet ends as other options for exiting the cabinet.
7. Wine dispensing kits also include a polyethylene waste bottle as an
optional method to collect wine waste. The waste bottle holder is hung
over the rim of a keg and the waste bottle is snapped into the holder.
8. Apply a bead of silicone around the perimeter of the drainer.
7
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
8
16
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
LUCKY AND PANTHER TOWER INSTRUCTIONS, Continued
Mounting the Beer/Wine Drainer to a Counter Top
1. Slide the 1/2” ID anti-microbial drain tubing over end of drainer
nipple. Feed the drain tubing through the drainer hole of the counter
top and the cabinet top. (The hose may be soaked in hot water prior
to doing this to make it more exible and better t around the drain
pipe.)
2. Use the nylon hose clips and self-drilling screws to secure the drain
tubing to the cabinet walls. Ensure the tubing will be out of the way of
1
2
loading and unloading kegs.
3. Route the anti-microbial tubing to the beer/wine collection drain or
waste container. It may be routed to the oor drain located in the right
rear corner of the cabinet. It must then be plumbed to an external
drain. There are also knockouts provided on the cabinet ends as other
options for exiting the cabinet.
4. Wine dispensing kits also include a polyethylene waste bottle as an
optional method to collect wine waste. The waste bottle holder is hung
3
4
5. Apply a bead of silicone around the perimeter of the drainer. This will provide a seal as well
as hold it in position.
over the rim of a keg and the waste bottle is snapped into the holder.
5
Running the Air Scoop Tubing to the Lucky or Panther Towers
1. You will need parts bag #67835 to attach the black corrugated air tubing to the air-cooled
tting on the Lucky or Panther towers.
2. Insert the black corrugated air tubing into the 1-1/8” ID vinyl tubing and tighten with the
hose clamp.
3. Attach the other end of the 1-1/8” vinyl tube to the air-cooled tting on the Lucky or
Panther tower and tighten with a hose clamp. Refer to Diagram 6 in the Appendix.
1
17
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
LUCKY AND PANTHER TOWER INSTRUCTIONS, Continued
Attaching the Beer Line to the Lucky or Panther Towers
21 1
1. On one end of the beer connector, cut o
the beer nut tting.
2. Push the beer line connector end over the
barbed end of the product supply line and
tighten with a clamp using a 1/4” nut driver or
slotted screwdriver.
3. Insert the rubber washer into the other end
of the beer line and attach to the keg coupler.
Tighten with an adjustable wrench but do not
over-tighten.
4. Repeat for each additional supply tube.
2
Attaching the Gas Line Tubing
3
1 3
Attaching the Tapping Hole Covers
1. To comply with NSF standards, please attach the tapping hole covers provided.
2. The two-piece cover can be adjusted to tighten snugly around beer lines and air scoop
tubing.
3. Position the covers tightly around the tubing and mount to the bottom side of the cabinet
top using a cordless drill with a 5/16” socket head bit and the self-drilling screws provided.
Please refer to Diagram 7 in the Appendix.
3
1. Attach one end of the gas line to a valve on the air distributor
manifold and tighten with a hose clamp.
2. Repeat for each additional product line.
3. Attach the other end of the gas line to the keg coupler and tighten
with a hose clamp.
1
18
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
LUCKY AND PANTHER TOWER INSTRUCTIONS, Continued
Attaching the Air Distributor Cover
1. To comply with NSF standards, the air distributor cover should be installed. It can be easily
removed to access the valves on the air distributor.
2. Each end of the cover has a knockout to provide clearance for the gas line. Remove the
appropriate knockout.
3. Route the gas line through the side of the cover and hang the cover on the air distributor
bracket.
1
Checking the System for Leaks
1. It is important to ensure the entire system is leak free.
2. The system can be checked by doing a pressure decay test or by tapping the system and inspecting for product
leaks and checking for gas leaks with soap and bubbles. Repair any leaks immediately.
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
19
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
APPENDIX - DIAGRAM 1
Single Tap Beer System
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
20
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
APPENDIX - DIAGRAM 2
Tapping in Series
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
21
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
APPENDIX - DIAGRAM 3
Drip Pan Drain Connection and
Tapping Hole Cover Installation
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
22
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
APPENDIX - DIAGRAM 4
Air Distributor Connections and
Excess Drip Pan Drain Tube Mounting
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
23
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
APPENDIX - DIAGRAM 5
Air Scoop Installation
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
24
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
APPENDIX - DIAGRAM 6
Air Sleeve Installation through
Countertop and Back Bar Cabinet
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
25
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
APPENDIX - DIAGRAM 7
Air Connection
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
26
PRODUCT INSTALLATION INSTRUCTIONS Dispensing Towers
CLEARANCE HOLE
FOR FLANGED NUT
1.5"
1.5"
3" OR THICKER
NOTE:
HOLES IN GRANITE AND
COOLER TOP ARE OFFSET TO
ALLOW MORE CLEARNCE FOR
AIR HOSE CONNECTION
VIN SERVICE AIR COOLED TOWERS MOUNTING REFERENCE
DISPENSING TOWERS
DRAFT ARMS, 2-6 FAUCET TEE TOWERS, LUCKY AND PANTHER TOWERS
APPENDIX - DIAGRAM 8
Lucky and Panther Tower
Mounting Reference
GRANITE TOP
COOLER TOP
NOTE:
HOLES IN GRANITE AND
COOLER TOP ARE CONCENTRIC
2 1/4"
4 1/4"
5"
CLEARANCE
HOLE FOR
FLANGED NUT
GRANITE TOP
COOLER TOP
1"
AIR HOSE
1.5"
1.5"
NOTE:
HOLES IN GRANITE AND
COOLER TOP ARE OFFSET TO
ALLOW MORE CLEARNCE FOR
AIR HOSE CONNECTION
1"
2 1/2"
1 1/2"
3" OR THICKER
2 1/2"
1 1/2"
CLEARANCE HOLE
FOR FLANGED NUT
PERLICK CORPORATION 8300 W. Good Hope Road, Milwaukee, WI 53223 • 800.558.5592 • perlick.com
Form No. Z2351
Rev. 04.17.19
27
Loading...