Page 1
1
M
—
PERKINS
PERKINS MACHINE COMPANY
1»
JUNIOR
I
¥1
INCLINABLE PRESS
Built by the
Warren, Massacliuselts, U. S. A.
FRED PERKINS, President
II. W. PERKINS, Treasurer
FOR BELT DRIVE
STANDARD JUNIOR MOTOR DRIVEN PRESS
Capacity ]/i" ilia, blank yir,
Capacity tlia. blank Kc" thick soft steel at 550 R.P.M.
n thick soft steel at 300 R.P.M.
PLAIN RENCII PRESS
PRESS
BUILDERS
FOR
FIFTY
YEARS
Page 2
“S” FRAME
6" Red lo Ways
•>
St an riant Speciftea tions
Weight: Press with stand approx. 160 Ihs.
Standard stroke Y\". (1" may he had at no
Diameter of shaft 2" at hearings and 1" at crank pin.
Distance between housings 3J4".
Distance hack from center 3". —
Distance from bed to ways,
Adjustment of piston I". Hole in piston
Area of bed, front to hack 5
Hole in bed 2" round.
Diameter
Distance from bed of press to floor when on stand 32".
Table
Floor space of stand, front to hack 20", right to left 19".
Treadle attached to leg of stand is self sustained.
Clutch is of sliding dog type with safety stop.
Single trip safety clutch furnished at extra cost.
Press may he inclined 15, 25 and 35 degrees.
Speeds; standard speed approx. 325 rpm. Can he furnished at
Motor: Y\ h.p. split phase 110 volt 60 cycle a.c. with switch, cord
Shipping weight standard press 2*10 Ihs.
extra
cost.)
stroke
down adjustment up t".
and right to left 9".
of flywheel 10" x 2"
area
18" right to left and 13" front to hack.
lower speed of 250 or higher speeds of 100 or 500 rpm.
and plug. Rev. 1750. "V"* hell drive used.
face, weight approx. 23 Ihs.
Prices
Prices subject to change without notice.
Press
on stand with motor drive and inclinable feature
Press on stand with motor
Press for bench with motor
Press on stand (plain for hell drive) with
Press on stand (plain for hell drive) without
Press for bench (plain for belt drive)
(Allowance for motor
drive without inclinable feature
drive with no si ami
inclinable
if not wanted) .
F. O. B. Warren, Mass.
inclinable feature 70.00
. $90.00
87.50
feature
82.50
72.50
65.00
6.00
!
i
:
:
J
I
6" DEPTH OF THROAT
Special Presses anri Variations
S frame
S frame (6" lied to ways,
S1K frame (6
S4K frame with knock out and cap front piston
6" Depth of throat frame .
Cap front piston on any press .
Knock out in piston (SK4 frame) right lo left .
Knock-out in piston front to hack
Single trip clutch on any frame
Bolster plates with 1]^ round hole ....
Extra die heights over 6" — first inch
Extra widths between housings
Special changes at small additional cost.
with standard stroke of % or I"
up lo 2", Inquire for longer strokes .
pj>" bed to ways
otherwise
and
standard) with strokes
I"
throat depth) extra
..........................
Each additional inch
—
first inch .
Each additional inch .
ex I ra $ 1
extra
extra
ex t ra
extra
extra
extra-
extra
ex Ira
0.00
15.00
15.00
25.00
25.00
5.00
10.00
10.00
15.00
7.50
10.00
5.00
10.00
5.00
MPelinerp
Standard presses in stock for immediate
Special strokes, “S” frames and S-4K frames require three lo four
days for delivery.
Material
All castings from alloy iron 40,000 Ihs. tensile
strength per square inch.
delivery.
\
!
!
'
!
i
Page 3
fiunrantvv
.Material and workman
ship guaranteed against
defects.
right to make changes.
We specialize in making
presses to meet your
We reserve the
requirements.
SINGLE TIME CLUTCH
ATTACHMENT
Kick
off type with no jar on
foot pedal.
.Ifo/or Variations
Standard motor
1750 r.p.m. 110 volt a.e. with huilt-in
switch, 10 foot cord and ping, suit aide
for use on a lighting circuit.
Extra for 220 volt motor
Extra for capacitor type motor
Extra for Direct current motor
Extra for three phase motor
with control wired
Extra for three phase motor only 7.50
Other modifications at regular prices.
S-tK FRAME
SHOWING KNOCK OUT IN
PISTON CAP FRONT PISTON
— ]4 ILP.
split
complete
3 PHASE MOTOR DRIVE
WITH SWITCH MOUNTING
phase
S 2.00
6.00
7.50
18.00
Page 4
STANDARD SINGLE FEED BOLL
•C';J
r
i
.
:'C
Feed Mtoli Specifications
Width of rolls 1 y2".
Diameter of rolls — lj-'g".
Length of feed from 0" to
Distance from lop
Hack and pinion drive.
Teed rolls mounted on holster plate.
Adjusting
Feed rolls can he furnished mounted for front to hack feed as well
Double feed rolls can also he furnished.
Price of standard single feed rolls — $90.00.
inquire for changes.
arm
on
end of crankshaft adjusts length of feed.
as right to left.
li e A iso Munufuvturv
Blanking Presses with eccentric shaft Model A
Long Stroke Presses Model A A
Inclinable Presses Model B
Double Acting Presses Model DA
Wheel
on
Back Model E
Sprue Cullers Model F
Horn Presses Model G
Straight Side Built-up Frame Presses Model II
Solid Frame Forging Presses Model 1
Toggle Presses Model J
Hand Screw Presses Model K
Foot Lever Presses Model L
Special presses built to order
4".
of holster plate to center of rolls
—
1
DIAL FEED
Hint Feed Specifications
Diameter of dial
Notched for 9 or more holes (no less than 9).
Standard
number of stations.
Positive stop for
Price of standard dial feed — $90.00.
Extra for positive slop — $15.00.
Extra for boring round holes for
Solid bed plate furnished as standard.
Die block as separate piece furnished at extra cost of $5.00.
Changes made at small extra cost.
plate
9".
dial
feed consists of 9" diameter plate notched for required
each
station furnished at extra
stations
—
cost.
each hole $2.00.
PERKINS MACHINE CO.
WARREN, MASS.
/
•r
Loading...