1600 WATT HEAVY DUTY HEAT GUN
4002205
Item Number W50078
OWNER’S MANUAL
WARNING
It is the owner and/or operators’ responsibility to study all WARNINGS, operating, and maintenance
instructions contained on the product label and instruction manual prior to operation of this product. The
owner/operator shall retain product instructions for future reference.
The owner and/or operator are responsible for maintenance, maintaining all decals or warning labels and
while in use, maintaining the unit in good working order. If the owner and/or operator are not fluent in English,
the product warnings and instructions shall be read and discussed with the operators’ native language by the
purchaser/owner or his designee. Make sure that the operator comprehends its contents. Safety information
shall be emphasized and understood prior to usage. The product shall be inspected per the operating
instructions.
Users of this product must fully understand these instructions. Each person operating this product must also
be of sound mind and body and must not be under the influence of any substance that might impair their
vision, dexterity or judgment.
Protect yourself and others by observing all safety information.
Failure to comply with instructions could result in personal injury and/or property damage!
If you encounter any problems or difficulties, please contact our customer service department at:
1-800-426-1262 between 6:30 a.m. and 4:30 p.m. Pacific time.
SAFETY GUIDELINES / DEFINITIONS
This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and
troubleshooting steps described within to ensure your safety and satisfaction. The contents of this instruction manual are
based upon the latest product information available at the time of publication. The manufacturer reserves the right to make
product changes at any time without notice.
WARNING: Read and understand this entire instruction manual before attempting to assemble, install, operate or
maintain this product. Failure to comply with the instructions may result in serious personal injury and/or property
damage!
The following signal words are used to emphasize safety warnings that must be followed when using this
product:
DANGER Indicates an imminently hazardous
situation that, if not avoided, WILL result in death or
serious injury.
WARNING Indicates a potentially hazardous
situation that, if not avoided, COULD result in death
or serious injury.
CAUTION Indicates a potentially hazardous situation
that, if not avoided, MAY result in minor or moderate
injury.
NOTICE Indicates important information, which if not
followed, MAY cause damage to equipment.
UNPACKING AND INSPECTION
After opening the carton, unpack your new product and related parts & accessories. Please inspect it carefully for
any damage that may have occurred during transit. Please check it against the photograph on carton. If any parts
are missing, please call customer service at 1-800-426-1262 between 6 a.m. and 5 p.m. Pacific time.
WARNING DO NOT operate this product if damaged during shipment, handling or misuse. Do not operate the
product until the parts have been replaced or the fault rectified. Failure to do so may result in serious personal injury
or property damage. All damaged parts must be repaired or replaced as needed prior to operating this product.
Check to see that all nuts, bolts and fittings are secure before putting this product into service. If you have any
questions, or require assistance with damaged or missing parts, please contact our factory customer service
department at: 1-800-426-1262.
Please have the serial number, model number, and date of purchase available for reference when calling.
SPECIFICATIONS
Temperature ..................................................... 1,000-1,100 °F
Wattage .........................................................................1600 W
Ampage ..........................................................................13.5 A
Voltage .............................................................. 120V AC 60Hz
Specifications are
subject to change
without notice.
IMPORTANT SAFETY INFORMATION
WARNING
HEAT GUNS ARE A SOURCE OF VERY HIGH TEMPERATURE FLAMELESS HEAT. AS WITH OTHER PRODUCTS
WHICH GENERATE EXTREMELY HIGH TEMPERATURES, READ, UNDERSTAND AND FOLLOW ALL
INSTRUCTIONS AND WARNINGS BEFORE OPERATING THIS PRODUCT. FAILURE TO DO SO MAY RESULT IN
FIRE, ELECTRICAL SHOCK, PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
1. Always use common sense and pay particular
attention to all the DANGER, WARNING, CAUTION
and NOTICE statements of this manual. The safety
instructions provided are not intended to cover all
possible conditions and practices that may occur
when operating, maintaining and cleaning power
tools.
2. Observe work area conditions. Do not use machines
or power tools in damp or wet locations. Don’t expose
to rain or snow. Keep work area well lighted. Do not
use electrically powered tools in the presence of
ammable gases or liquids. Do not bring combustible
materials near the tools. Power tools create sparks,
which may ignite the dust or fumes. Do not immerse
tool in liquids. Keep work area clean, well ventilated
and well lit. Cluttered work areas invite accidents.
3. Use personal protective equipment. Wear ANSI
approved safety goggles. Protective equipment such
as dusk mask, non-skid safety shoes, hard hat, heavy
duty work gloves or hearing protection used for appropriate conditions will reduce personal injuries.
4. Keep bystanders, children and visitors away while
operating this product. Distractions can cause you to
lose control.
1
IMPORTANT SAFETY INFORMATION
5. Stay alert. Watch what you are doing, and use common sense when operating this tool. Do not use this
product while tired or under the inuence of drugs,
alcohol, or medication. A moment of inattention while
operating this product may result in serious personal
injury. Keep proper footing and balance at all times.
Do not reach over or across running machines,
hoses, cords, etc.
6. Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be
caught in moving parts.
7. Work Safe. Operate tool a safe distance from yourself
and others in the work area. Keep proper footing and
balance at all times. Do not overreach, especially on
ladders. Be certain ladders being used are sturdy,
stable, on a rm surface and erected as safe working angles. Do not reach over or across running
machines, hoses, cords, etc.
8. Inspect tool before every use; do not use if parts are
loose or damaged.
9. Do not alter this product in any way.
10. Use the right tool for the job. Do not attempt to
force a small tool or attachment to do the work of a
larger industrial tool. Don’t use a tool whose performance is not adequate for your work. Do not modify
this tool and do not use this tool for a purpose for
which it was not intended.
11. People with pacemakers should consult their
physician(s) before use. Electromagnetic elds in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure. In
addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with power switch locked on.
• Properly maintain and inspect to avoid electrical
shock.
• Any power cord must be properly grounded.
Ground Fault Circuit Interrupter (GFCI) should
also be implemented – it prevents sustained
electrical shock.
12. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce
risk of electric shock. Do not use tool if plug is
damaged.
13. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
14. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
15. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the
risk of electric shock. Do not use tool if cord is
damaged.
16. When operating a power tool outdoors, use only a
3-wire grounded cord with a wire size of 14 gauge
or larger. We recommend they be listed by Underwriters Laboratories (UL) in the U.SA or (CSA)
Canadian Standards Association in Canada and be
suitable for outdoor use. Cords marked for outdoor
use are also suitable for indoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
17. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces
the risk of electric shock.
18. Use power tool ONLY on adequately rated circuits
to avoid overheating of electrical systems.
19. This tool comes with a circular safety stand that
should be used when setting the tool down while
operating or during the cool down period. Never
store while hot.
20. Prevent accidental starting. Ensure switch is in the
“OFF” position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your nger on the switch
or energizing power tools that have the switch “ON”
invites accidents.
21. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
22. Do not disassemble the heat gun.
23. Have your power tool serviced by a qualied repair
person using only identical replacement parts
This will ensure that the safety of the power tool is
maintained. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts
or failure to follow Maintenance Instructions may
create a risk of shock or injury.
24. Never let the power tool operate while unattended
and unplug when not in use or before servicing.
25. EXPLOSION AND FIRE PREVENTION. This
power tool produces extremely high temperatures,
It must be used with caution to prevent combustible
material from igniting. To prevent potential explo-
sion or re, the following precautions should be
followed:
• Hidden areas such as behind walls, ceilings,
oors, soft boards and other panels may contain
ammable materials that could be ignited by the
power tool when working in these locations. The
ignition of these materials may not be readily
apparent and could result in property damage and
injury to persons.
2
IMPORTANT SAFETY INFORMATION
• DO NOT use this power tool on hollow surfaces
such as outdoor siding, walls, softs, panels and
partitions, etc. Areas like this often contain am-
mable materials such as dust, wood chips, insulation, rodent nests and other debris which could
accidentally ignite. Use your heat gun for stripping
paint from solid woodwork with ins and outs such
as solid Interior trim, moulding, turnings, doors,
balusters and porch trim, etc.
• When working in these locations, keep the power
tool moving in a back-and-forth motion. Lingering
or pausing in one spot could ignite the panel or
the material behind it.
• Use extreme caution if the other side of the material being scraped is inaccessible, such as house
siding. The hidden side could catch on re if it
becomes too hot. Some buildings contain highly
ammable materials behind siding, oors, facia,
soft boards and other panels. Check these areas
before applying heat and do not use a heat tool
if ammable materials are present or if you are
unsure of the hidden material.
• When working with plastics, varnish, or similar
materials, gases develop that are easily am-
mable and can lead to explosions.
• Do not use near surfaces with cracks or near
metal pipes or ashing. Heat may be conducted
behind the work surface and ignite hidden material. The ignition of hidden materials may not
be readily apparent and can result in property
damage and injury.
• Do not use power tools in the presence of ammable liquids or gases.
• Do not use near combustible materials such as
dry grass, leaves, and paper which can scorch
and catch re.
• The nozzle becomes very hot. Do not lay the
heat gun on ammable surfaces when operating
the gun or immediately after shutting the gun off.
Always set the gun on a at, level surface so that
the nozzle tip is directed upwards and away from
the supporting surface.
• Do not point the power tool at people or animals
The intense heat can injure them.
• NEVER direct tool at clothing, hands or other
body parts. NEVER USE AS A HAIR DRYER.
• This power tool emits high temperature heat
at the nozzle. Keep hands and body out of the
heated air stream and never grasp the power
too by the nozzle. Wearing protective gloves and
safety glasses is recommended.
• NEVER touch work surface with nozzle. Keep at
least 1" away.
• Do not heat chemicals. Avoid the hazards of ignition or the release of harmful vapors.
• Do not use the Heat Gun on glass.
• Always hold tool by the handle or use the
included stand. NEVER touch the nozzle opening
or nozzle shield until the tool is cool.
• Tools and paint scrapings become very hot. To
avoid burns, use work gloves when scraping.
• Always treat the hot air units with the same
respect as an open ame.
• Because this power tool has the appearance of
a household hair dryer, keep out of the reach of
children and advise other persons having access
to it of its high heat capabilities.
• WARNING: With a heat gun, as with all other
tools, ALWAYS KEEP A FIRE EXTINGUISHER
HANDY and be sure to observe sensible re
precautions.
26. LEAD POISONING PREVENTION. Extreme care
should be taken when stripping paint. The peelings,
residue and vapors of paint may contain lead,
which is poisonous. Any paint applied to homes
before 1950 is likely to contain lead. Any paint
manufactured before 1977 may contain lead. Once
the paint is deposited on surfaces, hand-to-mouth
contact can result in the ingestion of lead. Exposure
to even low levels of lead can cause irreversible
brain and nervous system damage. Young and
unborn children are particularly vulnerable to lead
poisoning. Before beginning any paint removal
process you should determine whether the paint
you are removing contains lead. This can be done
by your local health department or by a professional who uses a paint analyzer to check the lead
content of the paint to be removed. Lead-based
paint should only be removed by a professional
and should not be removed using a heat gun. To
prevent potential lead poisoning, the following
precautions should be followed:
• Move the work piece outdoors. If this is not
possible, keep the work area well ventilated.
Open the windows and put an exhaust fan in one
of them. Be sure the fan is moving the air from
inside to outside.
• Remove or cover any carpets, rugs, furniture,
clothing, cooking utensils and air ducts.
• Place drop cloths in the work area to catch any
paint chips or peelings. Wear protective clothing
such as extra work shirts, overalls and hats.
• Work in one room at a time. Furnishings should
be removed or placed in the center of the room
and covered. Work areas should be sealed off
from the rest of the dwelling by sealing doorways
with drop cloths.
• Children, pregnant or potentially pregnant women
and nursing mothers should not be present in the
work area until the work is done and all cleanup
is complete.
• Wear a dust respirator mask of a dual lter respirator mask for dust and fumes which has been
approved by the Occupational Safety and Health
3
IMPORTANT SAFETY INFORMATION
Administration (OSHA) the National Institute of
Safety and Health (NIOSH), or the United States
Bureau of Mines. These masks and replaceable
lters are readily available at major hardware
stores. Be sure that the mask ts properly. Beards
and facial hair may keep masks from sealing
properly. Change the lters often. Disposable
paper masks are not adequate.
• Use caution when operating the heat gun. Keep
the heat gun moving as excessive heat will generate fumes which can be inhaled by the operator.
• Keep food and drink out of the work area. Wash
hands, arms and face and rinse mouth before
eating or drinking. Do not smoke or chew gum or
tobacco in the work area.
• NEVER breathe or swallow lead based paint in
any form.
• Clean up all removed paint and dust by wet
mopping the oors. Use a wet cloth to clean all
walls, sills and any other surface where paint dust
is clinging. Do not sweep, dry dust or vacuum.
Use a high phosphate detergent of trisodium
phosphate (TSP) to wash and mop areas.
• At the end of each work session, put the paint
chips and debris in a double plastic bag, close it
with tape or twist ties and dispose of properly.
• Remove protective clothing and work shoes in the
work area to avoid carrying dust into the rest of
the building. Wash work clothes separately. Wipe
shoes off with a wet rag and then wash it with the
work clothes. Wash hair and body thoroughly with
soap and water.
• Failure to follow adequate safety precautions
when working with lead paint could result In lead
poisoning.
27. Disconnect the plug from the power source before
making any adjustments or changing accessories.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
28. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
29. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
30. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
31. Store idle equipment. Disconnect the tool from
the power supply when not in use. Store in a dry
location to inhibit rust. Always lock up tools and
keep out of reach of children and other untrained
persons. Switch off all unused electrical tools when
stored. Disconnect battery from unit. Tools are
dangerous in the hands of untrained users.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
WARNING: This product and its packaging contain
a chemical known to the State of California to cause
cancer, birth defects, or other reproductive harm.
4
GROUNDING
WARNING: Improperly connecting the grounding wire can result in the risk of electric
shock. Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. Do not modify the power cord plug provided with the tool. Never
remove the grounding prong from the plug. Do not use the tool if the power cord or plug
is damaged. If damaged, have it repaired by a service facility before use. If the plug will
not fit the outlet, have a proper outlet installed by a qualified electrician.
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS
1. Tools marked with “Grounding Required” have
a three wire cord and three prong grounding plug. The plug must be connected to a
properly grounded outlet. If the tool should
electrically malfunction or break down,
grounding provides a low resistance path to
carry electricity away from the user, reducing
the risk of electric shock. (See Figure A.)
2. The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire
in the cord must be the only wire connected to
the tool’s grounding system and must never
be attached to an electrically “live” terminal.
(See Figure A.)
3. Your tool must be plugged into an appropriate outlet, properly installed and
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS
Figure A
grounded in accordance with all codes and
ordinances. The plug and outlet should look
like those in the following illustration. (See
Figure A)
1. Tools marked “Double Insulated” do not
require grounding. They have a special double
insulation system which satisfies OSHA
requirements and complies with the applicable
standards of Underwriters Laboratories, Inc.,
the Canadian Standard Association, and the
National Electrical Code. (See Figure B.)
2. Double insulated tools may be used in either
of the 120 volt outlets shown in the following
illustration. (See Figure B.)
EXTENSION CORDS
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one
tool may become hazardous when used on
another tool.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. If
Figure B
you must use an extension cord, be sure
that the gauge is large enough to carry
the amount of current necessary for your
power tool. If not, your tool may experience
a loss of power, excessive voltage drop or
overheating. The smaller the gauge number, the heavier the cord (see table below).
5
GROUNDING
SYMBOL DEFINITIONS
IMPORTANT:
their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
Symbol Name Explanation
V Volts Voltage (Potential)
A Amperes Current
Hz Hertz Frequency (Cycles per Second)
W Watt Power
Kg Kilograms Weight
Alternating Current Type of Current
Direct Current Type of Current
Alternating or Direct Current Type of Current
Earthing Terminal Grounding Terminal
Class II Construction Denotes Double Insulation
min Minutes Time
s Seconds Time
Ø Diameter Size of Drill Bits, Grinding Wheels, etc.
n
0 No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3,... Ring Selector Settings Speed, Torque or Position Settings
Some of the following symbols may be used on your tool. Please study them and learn
6
CONTROLS AND COMPONENTS
1. Three (3) Setting Power Switch
2. Air Intake Vent
3. Power Cord
4. Three (3) Position Steel Base
4
OPERATION
WARNING
USING THE HEAT GUN
1. Secure loose workpieces using a vise or
clamps (not included) to prevent movement while working.
2. Plug heat gun into property rated outlet.
3. With the power switch in the "OFF" posi-
tion, familiarize yourself with handling the
heat gun. Find the switch and air intake
vent.
4. To use the cool blower feature, move
power switch to "I" position.
5. Move power switch to "II" position. Heat
gun will reach full operating temperature
in a few minutes.
NOTE Smoke may appear during the initial
NOTICE If the blower motor in the heat
gun does not turn on when the switch is
set to either "I" or "II", turn the switch OFF
immediately. The heating element will
burn out if it is not cooled by the blower.
READ ALL WARNINGS IN THIS MANUAL BEFORE OPERATING THIS TOOL.
start up due to the burning of manufacturing oils. The smoke should
disappear in less than a minute.
2
1
3
6. Move air intake vent to desired position.
To obtain maximum heat output, turn
the ventilation shutter so it covers the
ventilation openings. Open will provide
slightly cooler air.
NOTICE Do not block the air intake
openings opposite the adjustable intake
cover. The heating element will burn out if
too much air intake is blocked.
7. For maximum heating, place the nozzle
one (1) inch from the area to be heated.
CAUTION NEVER position the nozzle
closer than one (1) inch to the workpiece,
it could scorch or ignite. This will also
cause premature failure of the heating
element.
8. To reduce heat output, turn the ventilation shutter to maximum opening and
move the nozzle away from the work.
9. The Heat Gun can be set on the adjustable stand to treat individual workpieces
by hand.
7
OPERATION
10. Tip: Operate the heat gun in the "I" posi-
tion (Cold) for two - three (2-3) minutes
before switching to "OFF" position. This
allows the heat gun to cool down and the
nozzle to become cool to the touch.
11. Move switch to "OFF" position.
NOTE: For the best operating results, per-
form a trial test on all materials.
PAINT STRIPPING
1. To strip paint, turn heat gun on and hold
it about one (1) inch from the surface
being stripped. Proper distance and
speed of stripping should be determined
by experience. It is best to hold the gun
further from the surface and to move
forward slowly. Slower speed is made up
for by the wider softened areas. Heat will
also penetrate deeper.
2. Regulate the outlet temperature by usIng
the shutter at the side of the heat gun.
Try different settings to nd the best
result with the paint you are stripping.
3. As paints starts to blister and bubble,
move gun slowly and steadIly across the
NOTE Always set the heat gun upright after
it is turned off, either for a short break
or for storage. Avoid laying the unit
on the side after shutdown. The heat
will remain in the unit and cooling will
take longer. Store the unit only after
the nozzle is cool. Unplug the unit
before storing to prevent accidental
startup.
surface. Follow closely with a scraping
knife (a two (2) inch wall scraper works
best) to remove the loosened paint. To
increase the speed of stripping the paint,
preheat the scraper as you move along
the work surface with the heat gun.
4. When stripping paint from grooves in
moulding, you may need to devise your
own scraping tools. Many people use old
screwdrivers with ground-down blades
and linoleum knives to do the job.
5. When the job is completed, move power
switch to "I" position. Operate blower for a
few minutes on cool.
8
TROUBLESHOOTING
Problem Probable Cause Solution
Will not turn on. 1. Power switch set at
"OFF"
2. No Power at outlet
3. Cord not connected
1. Turn Power Switch to
“l” or “ll”.
2. Check power at outlet.
3. Check that cord is
plugged in.
Unsatisfactory results 1. Improper heat
settings.
1. Adjust heat settings
for correct application.
CARE & MAINTENANCE
WARNING
"OFF" position and unplug power cord
from electrical outlet before attempting
cleaning or maintenance.
NOTICE
before it leaves the factory. This lubrication should last for the life of the tool. No
further lubrication is required.
Make sure that the ventilation openings are kept
clean and free of foreign matter.
Always turn power switch to
This power tool is lubricated
Use a mild soap and damp cloth to clean outside
of tool.
Do not use other cleaning agents, turpentine,
gasoline, lacquer thinner, paint thinner, or other
solvents that may contain chemicals which are
harmful to plastics and other insulating materials.
Never immerse tool in a liquid or allow a liquid to
enter inside the tool.
Never open the heat gun. Do not attempt to
repair the heat gun yourself, doing so will void
your warranty.
9
1 YEAR LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These warranties give specific legal
rights. Except where prohibited by local law, the law of the State of Washington governs all warranties and all exclusions and limitations of
warranties and remedies. There may be other rights which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal use and service. A
defective product may be returned for a free replacement within 90 days from the date of purchase, provided that product is returned to
place of purchase immediately after discovery of defect. After 90 days and up to one year from date of purchase, PERFORMANCE TOOL®
will replace at no charge any parts which our examination shall disclose to be defective and under warranty. These warranties shall be valid
only when a sales receipt showing the date of purchase accompanies the defective product or defective part(s) being returned. For part(s)
after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be replaced under normal
use and service. These warranties shall not apply to any product or part which is used for a purpose for which it is not designed, or which
has been repaired or altered in any way so as to affect adversely its performance or reliability, nor shall these warranties apply to any
product or part which has been subject to misuse, neglect, accident or wear and tear incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in connection with its
products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no express or implied
warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL® makes no implied warranty of merchantability
and no implied warranty of fitness for any particular purpose, except that for goods purchased primarily for personal, family or household
use and not for commercial or business use, PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise
applicable, an implied warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the
duration, expressly warranted above. The laws on limitation of implied warranties may differ from state to state, so the above limitations
may not apply in all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any manner related to any
product, or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective product or part shall be the
repair, or replacement thereof as provided above. The laws on limitation of remedies or on consequential, incidental or special damages
may vary from state to state, so the above limitations may not apply in all cases.
© Copyright 2011 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138
Loading...