Performance Designed 051038 User Manual

07/06/15

051-038-NA

Universal Media Remote for PS4 – N.A. Manual

(PDP logo)
(Official Licensed Product logo)

Universal Media Remote for PlayStation® 4
Instruction Manual
051-038-NA

WARNING

 Before using this product, carefully read this manual and retain it for future

reference. Additionally, read the instructions for the PlayStation® 4 System.

 Do not handle damaged or leaking batteries.

What you can do with the Universal Media Remote



The Universal Media Remote uses Bluetooth® wireless technology to operate

your PS4™ system and to control the playback of common types of media,
including Blu-ray Disc media.

 Infrared (IR) technology enables you to operate peripheral devices such as your

television, AV amplifier, and cable/satellite set-top box. For IR operation, you
must point the IR transmitter of the remote directly at the device. Check that
there are no obstructions between the remote control and the device.

Preparing for use

Remove the battery cover on the rear of the Universal Media Remote and insert 2 AAA
batteries. Make sure the batteries are in the correct position.

Operating the PS4™ system

Check the PS4™ system software version

To use the Universal Media Remote, the PS4™ system software must be version 2.55 or
later. You can check the system software version by selecting Settings -> System ->

System Information.

Pairing the Universal Media Remote with a PS4™ system

This operation is performed only once, when you are using the Universal Media Remote
for the first time.

1. Turn on the PS4™ system.

2. From the PS4™ system menu, select Settings -> Devices -> Bluetooth Devices

3. On the Universal Media Remote, press the PS4 device key

4. Next, press and hold the SHARE button and the PS button simultaneously until

the red LED begins to flash

5. Place the remote close to the PS4™ system and wait for “PDP Universal Media

Remote for PS4” to appear in the device list.

6. Using a connected controller, select “PDP Universal Media Remote for PS4” from

the list, and press the X button. When prompted, select “Yes”.

7. The red LED on the remote will illuminate for 3 seconds and then turn off,

indicating successful pairing.

Tips

 For the latest PS4™ usage instructions, refer to the user’s guide for the PS4™

system (manuals.playstation.net/document/).



For the latest Universal Media Remote instructions, refer to the online user’s

guide (support.pdp.com).

 Only one Universal Media Remote can be registered with the PS4™ system at a

time.

 When you pair the Universal Media Remote with another PS4™ system,

registration with the original PS4™ system is cleared. To use the remote with the
original PS4™ system, you will have to follow the pairing procedure again.

How to use the Universal Media Remote

DEVICE buttons

Switch between devices.
PS4™ system button Switch the remote to operate the PS4™ button
TV button Switch the remote to operate a TV
AMP button Switch the remote to operate an AV amplifier
CBL button Switch the remote to operate a cable/satellite set-top box

Buttons for operating a PS4™ system, TV, AV amplifier, or cable/satellite set-top box

The meaning of the icons shown in the table below is as follows:

(PS4) used to operate the PS4™ system
(TV) used to operate the TV
(AMP) used to operate the AV amplifier
(CBL) used to operate a cable/satellite set-top box

Operating a TV, A/V amplifier, or cable/satellite set-top box

You can use the Universal Media Remote to operate a TV, A/V amplifier, or set-top box.
Set the remote code to match the product in use.

NOTE: Some functions of your original remote may not be controlled by this remote.
Use the original remote, if available, to control such functions. Sometimes buttons other
than described in these instructions may actually perform the function. For example, the
channel and volume buttons might be used to navigate through menu choices. We
recommend you experiment with the remote to identify if such situations apply to your
equipment.

Programming TV, AMP, and CBL devices

There are two ways to program TV, AMP, and CBL devices, AUTO SEARCH MODE, or
MANUAL ENTRY MODE.

Auto Search Mode

1. Turn the target device ON.

2. Point the Universal Media Remote directly at the target device and make sure it

stays pointed at the device throughout the programming process.

3. On your Universal Media Remote, press and hold down the green PWR key and

the desired device key for about 5 seconds. The red LED on the remote will turn
on, indicating that it is now in Auto Search Mode.

4. Keep the remote pointed at the device.

5. When the remote locates the correct code, the device will turn OFF.

6. When the device turns OFF, immediately press any key to complete

programming.

7. If the red LED turns off and programming was not successful, please use manual

entry mode.

Manual Entry Mode

1. Turn the target device ON

2. Refer to the Manufacturer’s Code List included in the product documentation.

3. Find the brand name of the target device.