2014
Thank you for your purchasing of our
product.
If you have any questions that are not
covered in this manual, please contact us
by phone or
e-mail at
Sales@PerfectHomeTheater.com.
USER
MANUAL
FLM-7
FLM-8
P2-12
P3-12
Chassis Material: Full aluminum,
Colors: Silver / Black
Motherboard Support : Mini-ITX
Hard Drive Bays: 1 x 2.5″ + 1 x 3.5″ or 2.5″ (shared bay)
Optical Drive Bays: 1 x Slim slot loading drive, universal eject button (with FLM-8 only)
Ports: 2 x USB2.0, Front side (USB3.0 Ready, cable sold separately)
Expansion Slot: 1 x half height expansion slot
Cooling: Fanless
Dimension: 240 x 250 x 100mm (W x D x H)
Power Supply: 150 --180W PSU plus AC/DC Adapter (not included)
Remote Control: MCE compatible IR receiver & remote (not included)
Net Weight: 2.4KG
Specification
FLS-7 FLS-8
P3-12
8 7 6
4 2 5
Overview
1 Power Button & LED
2 ODD Eject Button (FLM-8)
3 USB Ports 2.0 & 3.0 on the side
4 IR Receiver Window
5 Heat Sinks
6 HDD/ODD tray
7 PCI Expansion Slot
8 Power Button PCB
Removing top panel.
Attention:
Our chassis are built with very small gaps
between front, top and back, so please be careful
when removing and reinstalling top panel. To
avoid scratches, please loose two screws in the
back and three screws in the bottom.
P4-12
3 1
Motherboard installation
Before installing motherboard into chassis please stick four
CPU cooler mounting nuts on the bottom of Motherboard.
Next install CPU and memory on Mobo, install backplate
and motherboard inside of chassis.
Next install CPU and memory on the Mobo, install
backplate and motherboard inside of chassis.
P5-12
1
3
4
5
2
Cooling system
These are the following parts of cooling system:
1.Lower CPU plate
2.Upper CPU plate (Intel or AMD)
3.Standard or short Heat Pipes (Attention: heat pipes are numbered.)
4.Heatsink blocks with thread.
5.Four screws for Cooling system (M3x10)
6.Thermal paste. (Supplied)
Most recent ITX motherboards have CPU socket close to right side of motherboard like ASRock
motherboard used in this manual. Such motherboards require short cooling pipes; HP4-97, sold
separately. Standard pipes are too long for this motherboard. They will extend ~17mm. There is no
problem with this particular motherboard, but other models may have tall object on line of pipes and
conflict with them. If your current motherboard require short pipes, please add them to your order.
Please keep your standard pipes for future motherboards with CPU in different location.
Mini ITX motherboard.
P6-12
6
DO NOT TIGHTEN ANY SCREWS UNTIL INSTALLATION IS FINISHED.
First assembly cooling system without paste, to find out the best position for pipes but do not tighten
screws yet. Next put it on CPU allign with CPU and move pipes toward or away from radiator if
nesesary.
Apply small amount of thermal paste on CPU
and put lower plate on CPU.
Apply thermal paste on both sides of thermal
pipes (3) and install pipes 1 and 2 first. Do not
tighten any screws yet. Than install pipes 3 and
4. Do not tighten any screws.
After setting position of pipes between plates,
remove upper plate, apply small amount of
thermal paste in groves on lower plate, set
pipes, apply small amount of thermal paste on
top of pipes and put upper plate back. Now,
even you have to move pipes a little you will
have clean assembly.
P7-12
Then put another two screws and set up assembly over CPU perfectly.
Now you can tighten screws.
First, Four screws in heatsink blocks. Pipes still
can move toward heatsink.
Next, use supplied wrench and tighten screws
keeping both plates together. Do not over
tighten screws!
At last, hand tighten long screws and you just
finished installation of cooling system for your
CPU.
P8-12
Now, when everything is on place, perfectly
arranged, tighten long screws first. Use fingers
only do not use wrench.
ODD/HDD bracket is hold in place by four
screws. Please remove screws and remove
ODD/HDD bracket.
Installing HDDs and ODD.
P9-12
Now it’s time to connect PSU and cables
Installing PCI Card .
This chassis allows you to install one low power
extension card.
P10-12
Now you can install drives on the bracket.
First 2.5” HDD on the bottom. (If you install two 2.5” HDs).
Next install SSD and ODD on the top.
If you didn’t install 2.5” HD and want to install 3.5” HD, do
it now.
Put HD between rubber dampers and use HD screws. Do
not overtight.
All drivers on the bracket.
Is everything OK? Install top cover and enjoy it.
Picture
(Not in scale)
Description/Type
Quantity
Application
M2x3
4
It should be Slim ODD drive (FLM-8 only)
M3x4
2
IR
M3x4
9
Motherboard
M3x5
16
2.5” HDD
6-32x6
12
3.5” HDD
M3x10
4
Heat sink blocks
M3x10
4
Heat sink plates
CPU retention screws
4
Heat sink mounting screws
Mounting nuts
4
Heat sink mounting nuts
Nuts shock pad
1
Nuts shock pad
Rubber pads
1
ODD
Heatsink pipes
4
Heatsink system
P9-12
Perfect Home Theater 163 America Blvd Ashland,
MA 01721-1869
www.shop.perfecthometheater.com
Perfect Home Theater 163 America Blvd Ashland,
MA 01721-1869
www.shop.perfecthometheater.com
Loading...