Pepperl Fuchs VDM28-15-L1-IO/73C/110122 Data Sheet
Distance measurement sensor with IO-Link interface
Dimensions
25.8
23.8
754.9
18
12
VDM28-15-L1-IO/73c/110/122
54.3
14.8
8
ø 5.2
6
Model Number
VDM28-15-L1-IO/73c/110/122
Distance sensor
with 4-pin, M12 x 1 connector
Features
• Distance measurement using object
• Measuring method PRT (Pulse
Ranging Technology)
• IO-link interface for service and
process data
• Analog output 0/4 mA ... 20 mA
• Accurate, clear, and reproducible
measuring results
• Laser class 1, eyesafe
Product information
The VDM28 distance measurement device
employs Pulse Ranging Technology (PRT).
It has a repeat accuracy of 5 mm with an
operating range of 0.2 ... 15 m and an
absolute accuracy of 25 mm.
The compact housing of the Series 28
photoelectric sensors, with dimensions of
88 mm (height), 26 mm (width) and 54 mm
(depth), make it the smallest device available
in its class.
62
93
2
9
9.8
M12
11
Electrical connection
Option:
1
2
3
4
+UB
Q2
0 V
C/Q1
analog
= Light on
= Dark on
Pinout
1
2
4
3
Wire colors in accordance with EN 60947-5-2
1 BN
2 WH
3 BU
4 BK
Indicators/operating means
2 2
1 4
35
88
102
10
54.6
(brown)
(white)
(blue)
(black)
1 Operating display green
SET
A
Q1
B
RUN
A
Q2
B
2 Signal display yellow
3 TEACH-IN button
4 Mode rotary switch
5 Laser output
Release date: 2017-10-16 12:26 Date of issue: 2017-10-16 297897_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
1
Distance measurement sensor with IO-Link interface
VDM28-15-L1-IO/73c/110/122
Technical data
General specifications
Measurement range 0.2 ... 15 m
Reference target Kodak white (90%)
Light source laser diode
Light type modulated visible red light
Laser nominal ratings
Note LASER LIGHT , DO NOT STARE INTO BEAM
Wave length 660 nm
Beam divergence < 1.5 mrad
Pulse length approx. 4 ns
Repetition rate 250 kHz
max. pulse energy < 1.5 nJ
Angle deviation max. ± 2°
Measuring method Pulse Ranging Technology (PRT)
Diameter of the light spot < 15 mm at a distance of 15 m at 20 °C
Ambient light limit 50000 Lux
Temperature influence typ. ≤ 0.25 mm/K
Functional safety related parameters
MTTFd 200 a
Mission Time (TM) 10 a
Diagnostic Coverage (DC) 0 %
Indicators/operating means
Operation indicator LED green
Function indicator 2 LEDs yellow for switching state
Teach-In indicator Teach-In: LED green/yellow equiphase flashing; 2.5 Hz
Control elements 5-step rotary switch for operating modes selection (threshold
Control elements Switch for setting the threshold values
Electrical specifications
Operating voltage UB10 ... 30 V DC / when operating in IO-Link mode: 18 ... 30 V
Ripple 10 % within the supply tolerance
No-load supply current I
Time delay before availability t
Interface
Interface type IO-Link
Protocol IO-Link V1.0
Cycle time min. 2.3 ms
Mode COM 2 (38.4 kBaud)
Process data witdh 16 bit
SIO mode support yes
Output
Signal output Push-pull output, short-circuit protected, reverse polarity
Switching voltage max. 30 V DC
Switching current max. 100 mA
Measurement output 1 analog output 4 ... 20 mA, short-circuit/overload protected
Switching frequency f 50 Hz
Response time 10 ms
Measurement accuracy
Absolute accuracy ± 25 mm
Repeat accuracy < 5 mm
Ambient conditions
Ambient temperature -30 ... 55 °C (-22 ... 131 °F)
Storage temperature -30 ... 70 °C (-22 ... 158 °F)
Mechanical specifications
Housing width 25.8 mm
Housing height 88 mm
Housing depth 54.6 mm
Degree of protection IP67
Connection 4-pin, M12 x 1 connector
Material
Housing Plastic ABS
Optical face Plastic pane
Mass 90 g
Compliance with standards and
directives
Standard conformity
Product standard EN 60947-5-2
Laser class IEC 60825-1:2007 Complies with 21 CFR 1040.10 and 1040.11
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
typ. service life 85,000 h at Ta = +25 °C
Teach Error:LED green/yellow non equiphase flashing; 8.0 Hz
setting and operating modes)
≤ 70 mA / 24 V DC
0
1.5 s
v
protected
except for deviations pursuant to Laser Notice No. 50, dated
June 24, 2007
2
Laserlabel
Accessories
PACTware 4.1
FDT Framework
VDM28 IODD
IODD for communication with VDM28-IOLink sensors
VDM28-IO-Link DTM
Device DTM for communication with
VDM28-IO-Link sensors
IO-Link-Master02-USB
IO-Link master, supply via USB port or
separate power supply, LED indicators,
M12 plug for sensor connection
IO-Link-Master-USB DTM
Communication DTM for use of IO-LinkMaster
IODD Interpreter DTM
Software for the integration of IODDs in a
frame application (e. g. PACTware)
OMH-05
Mounting aid for round steel ø 12 mm or
sheet 1.5 mm ... 3 mm
OMH-07-01
Mounting aid for round steel ø 12 mm or
sheet 1.5 mm ... 3 mm
OMH-21
Mounting bracket
OMH-22
Mounting bracket
OMH-VDM28-01
Metal enclosure for inserting protective
panes or apertures
OMH-VDM28-02
Mounting and fine adjustment device for
sensors from the 28 series
OMH-RLK29-HW
Mounting bracket for rear wall mounting
OMH-RL28-C
Weld slag cover model
OMH-K01
dove tail mounting clamp
OMH-K03
dove tail mounting clamp
OMH-MLV11-K
dove tail mounting clamp
Release date: 2017-10-16 12:26 Date of issue: 2017-10-16 297897_eng.xml
Loading...