Pepperl Fuchs UMC3000-30H-E5-5M-FA Data Sheet
Ultrasonic sensor UMC3000-30H-E5-5M-FA
Technical data
General specifications
Sensing range 200 ... 3000 mm
Adjustment range 240 ... 3000 mm
Dead band 0 ... 200 mm
Standard target plate 100 mm x 100 mm
Transducer frequency approx. 100 kHz
Response delay ≤ 200 ms
Indicators/operating means
LED green Operating display
LED yellow switching state
LED red error
Electrical specifications
Model Number
UMC3000-30H-E5-5M-FA
Single head system
Features
• Front of transducer and housing
manufactured entirely from
stainless steel
• Hygienic design, easy to clean
• Degree of protection IP68 / IP69K
• Programmable via DTM with
PACTWARE
• Mounting bracket MH-30H-01-FA
included in delivery
Description
Functional description
The enclosure and transducer of this ultrasonic sensor
form a hermetically sealed unit. Due to its special
design, this sensor is EHEDG compliant, and together
with an appropriate fixture are especially suitable for
applications where there are increased hygiene
requirements, such as in the manufacture and handling
of food.
For reliable operation, due to the special design of this
sensor, solely the enclosed mounting accessories must
be used, even in applications without special hygiene
requirements.
Diagrams
Characteristic response curve
Distance Y [m]
2.0
1.5
1.0
0.5
0.0
-0.5
-1.0
-1.5
-2.0
0 1 2 3 4 5
Y
flat surface 100 mm x 100 mm
X
round bar, Ø 25 mm
Distance X [m]
Operating voltage U
No-load supply current I
Input/Output
Input/output type 1 synchronization connection, bidirectional
0 Level 0 ... 1 V
1 Level 4 V ... U
Input impedance > 12 kΩ
Output rated operating current < 12 mA
Pulse length ≥ 200 µs
Pulse interval ≥ 2 ms
Synchronization frequency
Common mode operation ≤ 20 Hz
Multiplex operation ≤ 20/n Hz, n = number of sensors n ≤ 10 (factory setting: 5 )
Input
Input type 1 program input
Level (switch point 1) 0 ... 1 V
Level (switch point 2) 4 V ... U
Input impedance > 10 kΩ
Pulse length 2 ... 5 s
Output
Output type 1 switching output E5, PNP NO/NC, programmable
Rated operating current I
Voltage drop U
Repeat accuracy ≤ 0.1 % of full-scale value
Switching frequency f ≤ 2.8 Hz
Range hysteresis H programmable , preset to 1 mm
Temperature influence < 1.5 % of full-scale value
Ambient conditions
Ambient temperature -25 ... 60 °C (-13 ... 140 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type cable PUR , 5 m , With FDA approval
Core cross-section 5 x 0.5 mm
Degree of protection IP68 / IP69K
Material
Housing stainless steel 1.4404 / AISI 316L
Transducer Stainless steel 1.4435 / AISI 316L
Mass 425 g
Factory settings
Output near switch point: 240 mm
General information
Supplementary information Switch settings of the external programming adapter:
Compliance with standards and
directives
Standard conformity
Standards EN 60947-5-2:2007+A1:2012
Approvals and certificates
CCC approval CCC approval / marking not required for products rated ≤36 V
EHEDG Type EL Class I AUX
ECOLAB yes
B
0
e
d
10 ... 30 V DC
≤ 50 mA
B
B
200 mA , short-circuit/overload protected
≤ 2 V
2
LED window: VMQ Elastosil LR 3003/Shore 50 A
far switch point: 3000 mm
output function: Window mode
output behavior: NO contact
"output load": pull-down
"output logic": inv
FDA: All materials used for the sensor comply with CFR, title
21, §177.2600 (FDA)
IEC 60947-5-2:2007 + A1:2012
Release date: 2016-03-01 11:55 Date of issue: 2017-03-21 217778_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
1
Ultrasonic sensor UMC3000-30H-E5-5M-FA
Dimensions
ø 28
ø 30
11 3.5
Electrical Connection
100
BN
WH
GY
BK
BU
3.5 11
+U
B
Program input
Syncronization
Output
-U
B
ø 6.3
Additional Information
Programmable output modes
1. Window mode, normally open mode
A1 < A2:
A1
2. Window mode, normally closed mode
A2 < A1:
A2
3. One switch point, normally open mode
A1 -> ∞:
A2
4. One switch point, normally closed mode
A2 -> ∞:
A1
5. A1 -> ∞, A2 -> ∞: Object presence detection mode
Object detected: Switch output closed
No object detected: Switch output open
object distance
A2
A1
Accessories
V15S-G-0,3M-PUR-WAGO
Male cordset, M12, 5-pin, PUR cable with WAGO terminals
MH-30H-01-FA
Mounting aid, 30 mm acc. to EHEDG
UC-PROG1-USB
Programming adapter
Mounting
Comply with the minimum permissible bending radius of 70 mm, if you install the connecting
cable!
For reliable operation, you must use the included sensor mounting aid. This also applies for applications without special hygiene requirements.
Cleaning the Sensor in Areas with Hygiene Requirements
The sensor may only be used with the mounting aid included in the scope of delivery
as the fixture. Please note the information in the enclosed package insert for the
mounting aid with regard to the correct position of the seals and the correct process
for tightening the screw connections.
If the sensor as a whole is located in an area subject to hygiene requirements, the
sensor must be accessible from all sides for cleaning purposes. If the sensor is fitted
with only the front in an area subject to hygiene requirements, the front must be accessible from all sides accordingly.
The sensor and corresponding fixture are certified by ECOLAB. The components
were subjected to the cleaning agents listed in the certificate and are resistant to these agents. Use of other cleaning agents and chemicals is also possible. However, to
ensure the sensor and fixture offer resistance to these substances, corresponding
tests must be performed by the user.
For cleaning purposes, as a general rule you can completely cover the sensor including the fixture with foam and clean using a water jet. Cleaning at elevated temperatures of up to 85 °C is possible. It is not permitted to use high-pressure cleaning
equipment for cleaning purposes in areas subject to hygiene requirements.
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
2
Release date: 2016-03-01 11:55 Date of issue: 2017-03-21 217778_eng.xml
Loading...