Pepperl Fuchs UC6000-30GM-2EP-IO-V15 Data Sheet

Ultrasonic sensor UC6000-30GM-2EP-IO-V15

Model Number

UC6000-30GM-2EP-IO-V15

Single head system

Features

• IO-link interface for service and
process data

• Programmable via DTM with
PACTWARE

• 2 programmable switch outputs

• Selectable sound lobe width

• Synchronization options

• Temperature compensation

Diagrams

Characteristic response curve

Distance Y [mm]

1500

1000

500

0

-500

-1000

-1500
0 1000 2000 3000 4000 5000 6000 7000 8000 9000

Release date: 2017-10-24 12:02 Date of issue: 2017-10-27 191245_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

flat surface 100 mm x 100 mm

Y

X

round bar, Ø 25 mm

Distance X [mm]

wide sound lobe
narrow sound lobe

Technical data

General specifications

Sensing range 350 ... 6000 mm
Adjustment range 400 ... 6000 mm
Dead band 0 ... 350 mm
Standard target plate 100 mm x 100 mm
Transducer frequency approx. 65 kHz
Response delay minimum : 140 ms

Memory

Non-volatile memory EEPROM
Write cycles 100000

Indicators/operating means

LED green solid: Power on

LED yellow 1 solid: Object in evaluation range

LED yellow 2 solid: Object in evaluation range

LED red solid red: Error

Electrical specifications

Operating voltage U
No-load supply current I
Power consumption P
Time delay before availability t

Interface

Interface type IO-Link
Protocol IO-Link V1.0
Transfer rate Acyclical: typical 44 Bit/s
Cycle time min. 72 ms
Mode COM 2 (38.4 kBaud)
Process data witdh 16 bit
SIO mode support yes

Input/Output

Input/output type 1 synchronization connection, bidirectional

0 Level 0 ... 1 V
1 Level 4 V ... U
Input impedance > 12 kΩ
Output rated operating current < 12 mA
Pulse length 0.5 ... 300 ms (level 1)
Pulse interval ≥ 74 ms (level 0)

Synchronization frequency

Common mode operation ≤ 13 Hz
Multiplex operation ≤ 14 Hz / n , n = number of sensors , n ≤ 10

Output

Output type 2 push-pull (4 in 1) outputs, short-circuit protected, reverse

Rated operating current I
Voltage drop U
Repeat accuracy ≤ 0.1 % of full-scale value
Switching frequency f ≤ 1.5 Hz
Range hysteresis H 1 % of the adjusted operating range (default settings),

Temperature influence ≤ 1.5 % from full-scale value (with temperature

Ambient conditions

Ambient temperature -25 ... 70 °C (-13 ... 158 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)

Mechanical specifications

Connection type Connector plug M12 x 1 , 5-pin
Degree of protection IP67
Material

Housing Stainless steel 1.4305 / AISI 303

Transducer epoxy resin/hollow glass sphere mixture; polyurethane foam

Mass 165 g

Factory settings

Output 1 near switch point: 400 mm

Output 2 near switch point: 500 mm

Beam width wide

Compliance with standards and
directives

Standard conformity

B

0

0

v

e

d

factory setting: 280 ms

flashing: Standby mode or IO link communication

flashing: Learning function, object detected

flashing: Learning function, object detected

red, flashing: program function, object not detected

10 ... 30 V DC , ripple 10 %

≤ 60 mA
≤ 1 W
≤ 200 ms

B

(factory setting: n = 5 )

polarity protected
200 mA , short-circuit/overload protected
≤ 2.5 V

programmable

compensation)
≤ 0.2 %/K (without temperature compensation)

TPU
Polyamides

far switch point: 6000 mm
output function: Window mode
output behavior: NO contact

far switch point: 3000 mm
output function: Window mode
output behavior: NO contact

SS

1

Ultrasonic sensor UC6000-30GM-2EP-IO-V15

Standards EN 60947-5-2:2007+A1:2012

Approvals and certificates

UL approval cULus Listed, General Purpose
CSA approval cCSAus Listed, General Purpose
CCC approval CCC approval / marking not required for products rated ≤36 V

IEC 60947-5-2:2007 + A1:2012

Dimensions

ø73

32

5

36

LED

68

93

106

Additional Information

Switching output operating modes

1. Switching point mode

NO contact

NC contact

2. Window mode

NO contact

NC contact

3. Hysteresis mode

NO contact

NC contact

4. Retroreflective sensor mode

NO contact

NC contact

Near

switching

point

Far

switching

point

Electrical Connection

Pinout

ø7

M12

1

5

4

2

3

2

L+

Sync.

C/Q

Switch output 2

L-

1

5

4

3

Wire colors in accordance with EN 60947-5-2

1 BN
2 WH
3 BU
4 BK
5 GY

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

(brown)
(white)
(blue)
(black)
(gray)

Release date: 2017-10-24 12:02 Date of issue: 2017-10-27 191245_eng.xml

2