Pepperl Fuchs UC250-F77-IU-IO-V31 DATASHEET

Single head system

12

3.2

23

3.2

ø3.2

3 22

25

3 14

17

M8 x 1

189

31

LED YE LED GN/RD

Germany: [phone]Pepperl+Fuchs Group

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

USA: [phone] Singapore: [phone]

www.pepperl-fuchs.com [e-mail] [e-mail]

[e-mail]

Dimensions

Ultrasonic sensor

UC250-F77-IU-IO-V31

IO-Link interface for parameterization

<

Programmable via DTM with PACTWARE

<

Selectable sound lobe width

<

Synchronization options

<

Temperature compensation

<

Analog output

<

Technical Data

factory setting: 29 ms

programmable to 60 s

General specifications

Sensing range 20 ... 250 mm

Adjustment range 25 ... 250 mm

Dead band 0 ... 20 mm

Standard target plate 10 mm x 10 mm

Transducer frequency approx. 400 kHz

Response delay minimum : 8 ms

Sensor cycle time ≥ 8 ms (factory setting) ;

Memory

Release date: 2020-12-17 Date of issue: 2020-12-17 Filename: 261246_eng.pdf

1

Ultrasonic sensor UC250-F77-IU-IO-V31

Germany: [phone]Pepperl+Fuchs Group

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

USA: [phone] Singapore: [phone]

www.pepperl-fuchs.com [e-mail] [e-mail]

[e-mail]

Technical Data

Non-volatile memory EEPROM

Write cycles 300000

Indicators/operating means

LED green solid: power on

LED yellow solid: object in evaluation range

LED red solid: fault

Electrical specifications

Operating voltage U

flashing: standby mode or IO-Link communication

flashing: programming of the limits, object detected

flashing: programming limits, object not detected

18 ... 30 V DC , ripple 10 %

B

SS

No-load supply current I

Power consumption P

Time delay before availability t

0

v

0

≤ 50 mA

≤ 500 mW

≤ 300 ms

Interface

Interface type IO-Link (available after activation via programming button until next reset)

Input/Output

Input/output type 1 synchronization connection, bidirectional

0 Level 0 ... 1 V

1 Level 2.5 V ... U

B

Input impedance > 22 kΩ

Output rated operating current current source < 2.5 mA

Pulse length ≥ 1 ms with external control, low active

Synchronization frequency

Common mode operation ≤ 141 Hz

Multiplex operation ≤ 141 Hz / n , n = number of sensors , n ≤ 10

Output

Output type 1 analog output 0 (4) ... 20 mA or

1 analog output 0 ... 10 V

Resolution current output: evaluation range [mm]/3200 but ≥ 0.35 mm

voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm

Deviation of the characteristic curve ≤ ± 1 % of full-scale value

Repeat accuracy ≤ ± 0.1 % of full-scale value

Load impedance current output: ≤ 500 Ohm

voltage output: ≥ 1000 Ohm

Temperature influence ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after

switching on the sensor ; 0.17 %/K (without temperature compensation)

Compliance with standards and directives

Standard conformity

Standards EN 60947-5-2:2007+A1:2012

IEC 60947-5-2:2007 + A1:2012
EN 60947-5-7:2003
IEC 60947-5-7:2003

Approvals and certificates

UL approval cULus Listed, Class 2 Power Source

CCC approval CCC approval / marking not required for products rated ≤36 V

Ambient conditions

Ambient temperature current output -25 ... 60 °C (-13 ... 140 °F) voltage output -25 ... 70 °C (-13 ... 158 °F)

Storage temperature -40 ... 85 °C (-40 ... 185 °F)

Mechanical specifications

Connection type Connector plug M8 x 1 , 4-pin

Degree of protection IP67

Material

Housing Polycarbonate

Transducer epoxy resin/hollow glass sphere mixture; polyurethane foam

Release date: 2020-12-17 Date of issue: 2020-12-17 Filename: 261246_eng.pdf

2