Pepperl Fuchs UC250-F77-EP-IO-0.2M-V31 Data Sheet

Ultrasonic sensor UC250-F77-EP-IO-0,2M-V31

Model Number

UC250-F77-EP-IO-0,2M-V31

Single head system

Features

• IO-link interface for service and
process data

• Programmable via DTM with
PACTWARE

• Continuous distance value via IO­Link process data

• Selectable sound lobe width

• Synchronization options

• Temperature compensation

• Push-pull output

Diagrams

Characteristic response curve

Distance Y [mm]

100

flat surface 100 mm x 100 mm

50

0

-50

round bar, Ø 25 mm

-100
0 50 100 150 200 250 300 350 400 450

Distance X [mm]

Y

X

Release date: 2018-07-25 15:49 Date of issue: 2018-07-25 266632-100000_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

wide sound beam
medium-sized sound beam
narrow sound beam

Technical data

General specifications

Sensing range 20 ... 250 mm
Adjustment range 25 ... 250 mm
Dead band 0 ... 20 mm
Standard target plate 10 mm x 10 mm
Transducer frequency approx. 400 kHz
Response delay minimum : 8 ms

Sensor cycle time ≥ 8 ms (factory setting) ;

Memory

Non-volatile memory EEPROM
Write cycles 300000

Indicators/operating means

LED green solid: power on

LED yellow solid: object in evaluation range

LED red solid: error

Electrical specifications

Operating voltage U
No-load supply current I
Power consumption P
Time delay before availability t

Interface

Interface type IO-Link (via C/Q = Pin 4)
Device profile Smart Sensor
Transfer rate COM 2 (38.4 kBaud)
IO-Link Revision 1.1
Min. cycle time 2.3 ms
Process data witdh 16 bit
SIO mode support yes
Device ID 0x300300 (3146496)
Compatible master port type A

Input/Output

Input/output type 1 synchronization connection, bidirectional

0 Level 0 ... 1 V
1 Level 2.5 V ... U
Input impedance > 22 kΩ
Output rated operating current current source < 2.5 mA
Pulse length ≥ 1 ms with external control, low active

Synchronization frequency

Common mode operation ≤ 141 Hz
Multiplex operation ≤ 141 Hz / n , n = number of sensors , n ≤ 10

Output

Output type 1 push-pull (4 in 1) output, short-circuit protected, reverse

Rated operating current I
Voltage drop U
Repeat accuracy ≤ ± 0.1 % of full-scale value
Switching frequency f factory setting: 20 Hz programmable max. 45 Hz
Range hysteresis H 1 % of the adjusted operating range (default settings),

Temperature influence ≤ ± 0.75 % of the end value (with temperature compensation)

Ambient conditions

Ambient temperature -25 ... 70 °C (-13 ... 158 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)

Mechanical specifications

Connection type Cable connector M8 x 1 , 4-pin , L = 200 mm
Degree of protection IP67
Material

Housing Polycarbonate

Transducer epoxy resin/hollow glass sphere mixture; polyurethane foam
Installation position any position
Mass 20.5 g
Tightening torque, fastening screws max. 0.2 Nm

Factory settings

Output near switch point: 25 mm

Beam width wide

Compliance with standards and
directives

Standard conformity

Standards EN 60947-5-2:2007+A1:2012

B

0

0

v

e

d

factory setting: 29 ms

programmable to 60 s

flashing: standby mode or IO-Link communication

flashing: switch point programming, object detected

flashing: switch point programming, object not detected

10 ... 30 V DC , ripple 10 %

≤ 40 mA
≤ 400 mW
≤ 300 ms

B

polarity protected
100 mA , short-circuit/overload protected
≤ 2.5 V

programmable , min. 1 mm

from 10 minutes after switching on the sensor ; 0,17 %/K
(without temperature compensation)

far switch point: 250 mm
Output mode: Window mode
Output logic: normally open

IEC 60947-5-2:2007 + A1:2012
IEC 61131-9:2013

SS

1

Ultrasonic sensor UC250-F77-EP-IO-0,2M-V31

Approvals and certificates

UL approval cULus Listed, Class 2 Power Source
CCC approval CCC approval / marking not required for products rated ≤36 V

Dimensions

LED YE LED GN/RD

12

31

18

ø 4.3

L

25

ø 3.2

322

23

3.2

3.2

3 14

17

Additional Information

Switching output modes

1. Switch point mode

Switch point 1

(SP 1)

Normally open

Normally closed

2. Window mode

Normally open

Normally closed

3. Hysteresis mode

Normally open

Normally closed

4. Retroreflective mode

Normally open

Normally closed

Switch point 2

(SP 2)

M8 x 1

Electrical Connection

*if not used connect to ground (0V)

Pinout

1

2

4

3

24

13

L+

Synchronization*

C/Q (Switching output/
IO-Link Interface)

L-

Release date: 2018-07-25 15:49 Date of issue: 2018-07-25 266632-100000_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

2