Pepperl Fuchs UC2000-L2-E4-V15 Data Sheet

Ultrasonic sensor UC2000-L2-E4-V15

Technical data

General specifications

Sensing range 60 ... 2000 mm
Adjustment range 80 ... 2000 mm
Dead band 0 ... 60 mm
Standard target plate 100 mm x 100 mm
Transducer frequency approx. 175 kHz

Model Number

UC2000-L2-E4-V15

Single head system

Features

• Sensor head bidirectional and ro­tatable

• Function indicators visible from all
directions

• Quick mounting bracket

• Selectable sound lobe width

• Programmable

Diagrams

Characteristic response curve

Distance Y [mm]

1000

flat surface 100 mm x 100 mm

800

600

400

200

0

-200

-400

-600
0 500 1000 1500 2000 2500 3000 3500 4000

Y

X

round bar, Ø 25 mm

Distance X [mm]

wide sound lobe
narrow sound lobe

Response delay minimum : 60 ms

Indicators/operating means

LED green Operating display
LED yellow switching state
LED red error

Electrical specifications

Operating voltage U

No-load supply current I

Interface

B

0

Interface type Serial interface (programming adapter required)

Input/Output

Input/output type 1 synchronization connection, bidirectional

0 Level 0 ... 1 V
1 Level 4 V ... U

Input impedance > 12 kΩ
Output rated operating current < 12 mA
Pulse length 0.5 ... 300 ms (level 1)
Pulse interval ≥ 33 ms (level 0)

Synchronization frequency

Common mode operation ≤ 30 Hz
Multiplex operation ≤ 33 Hz / n , n = number of sensors , n ≤ 10

Input

Input type 1 program input
Level (switch point 1) 0 ... 1 V
Level (switch point 2) 4 V ... U

Input impedance > 10 kΩ
Pulse length 2 ... 10 s

Output

Output type 1 switching output E4, NPN, NO/NC, programmable
Rated operating current I
Voltage drop U
Repeat accuracy ≤ 0.1 % of full-scale value

d

e

Switching frequency f ≤ 5 Hz
Range hysteresis H programmable , preset to 1 mm
Temperature influence < 1.5 % of full-scale value

Ambient conditions

Ambient temperature -25 ... 70 °C (-13 ... 158 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)

Mechanical specifications

Connection type Connector M12 x 1 , 5-pin
Degree of protection IP67
Material

Housing PA-GF35
Transducer epoxy resin/hollow glass sphere mixture; polyurethane foam

Mass 115 g

Factory settings

Output near switch point: 80 mm

Beam width wide
Evaluation procedure averaging (MxN)

General information

Supplementary information Switch settings of the external programming adapter:

Compliance with standards and
directives

Standard conformity

Standards EN 60947-5-2:2007 + A1:2012

Ex works settings: 120 ms

10 ... 30 V DC , ripple 10 %

SS

≤ 50 mA

9600 BPS, no parity, 8 data bits, 1 stop bit

B

(factory setting: n = 5 )

B

200 mA , short-circuit/overload protected
≤ 2 V

far switch point: 2000 mm
output function: Window mode
output behavior: NO contact

M = 5
N = 2

"output load": pull-up
"output logic": inv

IEC 60947-5-2:2007 + A1:2012

Release date: 2016-02-15 08:50 Date of issue: 2016-02-15 277763_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

Approvals and certificates

UL approval cULus Listed, General Purpose

CSA approval cCSAus Listed, General Purpose

CCC approval CCC approval / marking not required for products rated

≤36 V

1

Ultrasonic sensor UC2000-L2-E4-V15

Dimensions

LED yeLED gnLED ye

40

3

LED gn

28

7

67

40

M12 x 1

Electrical Connection

Pinout

40

T

out pwr

5.5

60

1

4

2

5

3

2

L+

Switch output

Program input

Synchronization

L-

1

5

4

20

30

ø 5.546

3

Wire colors in accordance with EN 60947-5-2

1 BN
2 WH
3 BU
4 BK
5 GY

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

(brown)
(white)
(blue)
(black)
(gray)

Release date: 2016-02-15 08:50 Date of issue: 2016-02-15 277763_eng.xml

2