Pepperl Fuchs UC2000-30GM-IUEP-IO-V15 Data Sheet

Ultrasonic sensor UC2000-30GM-IUEP-IO-V15

Technical data

General specifications

Sensing range 90 ... 2000 mm
Adjustment range 120 ... 2000 mm
Dead band 0 ... 90 mm
Standard target plate 100 mm x 100 mm
Transducer frequency approx. 200 kHz

Model Number

UC2000-30GM-IUEP-IO-V15

Single head system

Features

• IO-link interface for service and
process data

• Programmable via DTM with
PACTWARE

• Switch output and analog output

• Selectable sound lobe width

• Synchronization options

• Temperature compensation

Diagrams

Characteristic response curve

Distance Y [mm]

600

flat surface
100 mm x 100 mm

400

200

0

Response delay minimum : 65 ms

Memory

Non-volatile memory EEPROM
Write cycles 100000

Indicators/operating means

LED green solid: Power on

LED yellow 1 solid: Object in evaluation range

LED yellow 2 solid: Object in evaluation range

LED red solid red: Error

Electrical specifications

Operating voltage U

No-load supply current I
Power consumption P
Time delay before availability t

Interface

Interface type IO-Link
Protocol IO-Link V1.0
Transfer rate Acyclical: typical 95 Bit/s
Cycle time min. 33.6 ms
Mode COM 2 (38.4 kBaud)
Process data witdh 16 bit
SIO mode support yes

Input/Output

Input/output type 1 synchronization connection, bidirectional

0 Level 0 ... 1 V
1 Level 4 V ... U
Input impedance > 12 kΩ
Output rated operating current < 12 mA
Pulse length 0.5 ... 300 ms (level 1)
Pulse interval ≥ 33 ms (level 0)

Synchronization frequency

Common mode operation ≤ 30 Hz
Multiplex operation ≤ 33 Hz / n , n = number of sensors , n ≤ 10

Output

Output type 1 push-pull (4 in 1) output, short-circuit protected, reverse

Rated operating current I
Voltage drop U
Resolution current output: evaluation range [mm]/3200 but ≥ 0.35 mm

B

0

0

v

e

d

factory setting: 125 ms

flashing: Standby mode or IO link communication

flashing: Learning function, object detected

flashing: Learning function, object detected

red, flashing: program function, object not detected

10 ... 30 V DC , ripple 10 %SS
15 ... 30 V voltage output

≤ 60 mA
≤ 1 W
≤ 120 ms

B

(factory setting: n = 5 )

polarity protected
Current output 4 mA ... 20 mA or
voltage output 0 V ... 10 V configurable
200 mA , short-circuit/overload protected
≤ 2.5 V

voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm

-200

-400

round bar, Ø 25 mm

-600

0 500 1000 1500 2000 2500 3000 3500

Y

Release date: 2017-10-24 12:01 Date of issue: 2017-10-27 191239_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

X

wide sound lobe
narrow sound lobe

Distance X [mm]

Deviation of the characteristic curve ≤ 0.2 % of full-scale value
Repeat accuracy ≤ 0.1 % of full-scale value
Switching frequency f ≤ 4 Hz
Range hysteresis H 1 % of the adjusted operating range (default settings),

Load impedance current output: ≤ 300 Ohm

Temperature influence ≤ 1.5 % from full-scale value (with temperature

Ambient conditions

Ambient temperature -25 ... 70 °C (-13 ... 158 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)

Mechanical specifications

Connection type Connector plug M12 x 1 , 5-pin
Degree of protection IP67
Material

Housing Stainless steel 1.4305 / AISI 303

Transducer epoxy resin/hollow glass sphere mixture; polyurethane foam

Mass 72 g

Factory settings

Output 1 near switch point: 120 mm

programmable

voltage output: ≥ 1000 Ohm

compensation)
≤ 0.2 %/K (without temperature compensation)

TPU
Polyamides

far switch point: 2000 mm
Output mode: Window mode
output behavior: NO contact

1

Ultrasonic sensor UC2000-30GM-IUEP-IO-V15

Output 2 near limit: 120 mm

Beam width wide

Compliance with standards and
directives

Standard conformity

Standards EN 60947-5-2:2007+A1:2012

Approvals and certificates

UL approval cULus Listed, General Purpose
CSA approval cCSAus Listed, General Purpose
CCC approval CCC approval / marking not required for products rated ≤36 V

far limit: 1000 mm
Output mode: rising ramp
output behavior: Current output 4 mA ... 20 mA

IEC 60947-5-2:2007 + A1:2012
EN 60947-5-7:2003
IEC 60947-5-7:2003

Dimensions

M30 x 1.5

2

5

56

36

LED

81

93

Additional Information

Analog output operating modes

Analog functions

Near trip value Distant trip value

Rising ramp

Falling ramp

Zero point line

0

Switching output operating modes

1. Switching point mode

NO contact

NC contact

2. Window mode

Near

switching

point

Far

switching

point

Electrical Connection

Pinout

T1 T2

ø7

M12

1

5

4

2

3

2

L+

Sync.

C/Q

Analog output

L-

1

5

4

NO contact

NC contact

3. Hysteresis mode

NO contact

NC contact

4. Retroreflective sensor mode

NO contact

NC contact

3

Release date: 2017-10-24 12:01 Date of issue: 2017-10-27 191239_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

2