Pepperl Fuchs UC10000-F260-IE9R2 Data Sheet

		Ultrasonic sensor	UC10000-F260-IE9R2

Technical data

General specifications

Sensing range

Adjustment range

Dead band

Standard target plate

Transducer frequency

Nominal ratings

Time delay before availability tv

Limit data

Permissible cable length

Indicators/operating means

LED yellow

Electrical specifications

Rated operating voltage Ue

Operating voltage UB

Ripple

No-load supply current I0

Input/Output

Model Number

Input/output type

0 Level

UC10000-F260-IE9R2

1 Level

Single head system

Input impedance

Number of sensors

Switching output

Features

Output type

•

Large sensing range

Repeat accuracy R

•

Adjustable Bracket

Operating current IL

Voltage drop

• Programmable by means of Inter-

Switch-on delay

Analog output

face (see accessories) and SON-

Output type

PROG

Default setting

• Analog output 4 ... 20 mA

Linearity error

•

2 switch outputs

Load resistor

Ambient conditions

•

Synchronization options

Ambient temperature

Storage temperature

•

Temperature compensation

Shock resistance

Vibration resistance

Mechanical specifications

Description

Connection type

This ultrasonic sensor is a contactless distance sensor

Degree of protection

Material

based on the echo run time principle. It is suitable for

Housing

the detection of solid, liquid or powder sound-reflecting

Transducer

objects. The unique sensor design allows easy move-

Installation position

ment of the direction of sound radiation in all spatial di-

Mass

rections by up to 10° without additional an additional

Compliance with standards and

assembly device.

directives

Standard conformity

Standards

Diagrams

<![if ! IE]> <![endif]>eng.xml

Characteristic response curve

Distance Y [mm]

Approvals and certificates

UL approval

<![if ! IE]> <![endif]>250791

1800

1600

CSA approval

1400

1200

CCC approval

1000

<![if ! IE]> <![endif]>-16

800

600

<![if ! IE]> <![endif]>02

400

200

<![if ! IE]> <![endif]>2016-

2

1

-200

0

<![if ! IE]> <![endif]>issue:of

-400

-1200

-600

-800

-1000

<![if ! IE]> <![endif]>Date

-1400

-1800

-1600

<![if ! IE]> <![endif]>08:1516

0

2000

4000

6000

8000

10000

12000

14000

16000

Y

X

Distance X [mm]

<![if ! IE]> <![endif]>-02-

Curve 2: round bar, Ø 25 mm

<![if ! IE]> <![endif]>2016

Curve 1: flat surface 100 mm x 100 mm

<![if ! IE]> <![endif]>Release date:

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

800 ... 10000 mm

800 ... 10000 mm

0 ... 800 mm

100 mm x 100 mm

approx. 60 kHz

280 ms

max. 300 m

solid: switching state switch output flashing: misadjustment

24 V DC

15 ... 30 V (including ripple)

In supply voltage interval 15 ... 20 V sensitivity reduced to 20% ... 0%

≤10 %

≤75 mA

1 synchronization connection, bidirectional ≤ 3 V

15 ... 30 V typ. 0.9 kΩ

max. 10

2 switch outputs PNP, NC

± 15 mm

150 mA , short-circuit/overload protected ≤ 3 V

800 ms

1 current output 4 ... 20 mA rising ramp

800 ... 10000 mm

≤1.5 %

≤300 Ω

-25 ... 70 °C (-13 ... 158 °F)

-40 ... 85 °C (-40 ... 185 °F)

30 g , 11 ms period

10 ... 55 Hz , Amplitude ± 1 mm

screw terminals , PG 13.5 cable gland

IP65

UP 1225 SF/R8

epoxy resin/hollow glass sphere mixture; polyurethane foam

any position

1800 g

EN 60947-5-2:2007 + A1:2012

IEC 60947-5-2:2007 + A1:2012

EN 60947-5-7:2003

IEC 60947-5-7:2003

cULus Listed, General Purpose

cCSAus Listed, General Purpose

CCC approval / marking not required for products rated ≤36 V

1

		Ultrasonic sensor	UC10000-F260-IE9R2

Dimensions

112	160
	ø 8.5
	<![if ! IE]> <![endif]>97.6	<![if ! IE]> <![endif]>160

Additional Information

Area definitions

Smin	A	E	Smax
			ca. 5°
Blind	Sensing range
area
Analog output			20 mA
			10 V
4 mA
0 mA/0 V

Electrical Connection

L+

+UB

XI

Input

IA/UA

Analog output

S

Switch output 1

SX

Switch output 2

GND

-UB

Accessories

DA5-IU-C

Digital display unit

3RX4000-PF

PC interface

V15S-G-2M-PVC

Cable connector, M12, 5-pin, PVC cable

V1-M20-80

Receptacles, M12/M20; plastic version

Danger!

This product must not be used in applications in which the safety of persons depends on the device function.

This product is not a safety component in accordance with the EU Machinery Directive.

Assembly and connection

When installing the sensor, make sure that the space filled by the sound cone is free from interfering objects. Objects in the blind zone cause cause false signals. Implement suitable measures to ensure that objects cannot enter the blind zone.

The electrical connection is made via screw terminals. The connections are protected against reverse polarity, short circuits and overloads. Shielded cables are recommended if there is electrical interference.

Setting

<![if ! IE]>

<![endif]>IA/UA GND L+

LEDP1(A)P2(E)

	<![if ! IE]> <![endif]>XI
<![if ! IE]> <![endif]>S	<![if ! IE]> <![endif]>NO/NC
<![if ! IE]> <![endif]>SX	<![if ! IE]> <![endif]>NO/NC

The detection range limits Smin and Smax are fixed (see Technical data). Within these limits, the switch points A and E are set using a potentiometer. Switch point A must be smaller than switch point E. If this is not the case, the LED flashes and correct switching is not possible.

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

<![if ! IE]>

<![endif]>Release date: 2016-02-16 08:15 Date of issue: 2016-02-16 250791_eng.xml

2