Pepperl Fuchs UBE100018GM40ASE2V1Y20534 Data Sheet

Through-beam ultrasonic barrier UBE1000-18GM40A-SE2-V1-Y205349

Technical data

General specifications

Sensing range 15 ... 1000 mm
Standard target plate 100 mm x 100 mm
Transducer frequency approx. 255 kHz

Indicators/operating means

LED green Power on
LED yellow switching state
LED red error, object uncertain

Electrical specifications

Model Number

UBE1000-18GM40A-SE2-V1-Y205349

Single head system

Features

•Short design, 40mm

• Function indicators visible from all
directions

• Switch output

•Program input

• 58 mm pre-taught sensor spacing

Diagrams

Characteristic response curve

Distance Y [mm]

20

15

10

5

0

-5

-10

-15

-20
0 200 400 600 800 1000

X

Y

Obstacle: flat plate 100 mm x 100 mm

Distance X [mm]

Operating voltage U
No-load supply current I

Input

B

0

Input type 1 program input

Output

Output type PNP, NO
Rated operating current I
Default setting emitter/receiver spacing = 58 mm
Voltage drop U
Switch-on delay t

d

Switching frequency f ≤ 100 Hz

e

on

Ambient conditions

Ambient temperature -25 ... 70 °C (-13 ... 158 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)

Mechanical specifications

Connection type Connector M12 x 1 , 4-pin
Degree of protection IP67
Connection V1 connector (M12 x 1), 4-pin
Material

Housing brass, nickel-plated
Transducer epoxy resin/hollow glass sphere mixture; foam polyurethane,

Mass 25 g

Compliance with standards and
directives

Standard conformity

Standards EN 60947-5-2:2007 + A1:2012

Approvals and certificates

UL approval cULus Listed, General Purpose
CSA approval cCSAus Listed, General Purpose
CCC approval CCC approval / marking not required for products rated ≤36 V

Dimensions

10 ... 30 V DC , ripple 10 %
≤ 20 mA

free air path: -U
input impedance: > 4,7 kΩ program pulse: ≥ 1 s

... +1 V, object: +6 V ... +UB

B

SS

200 mA , short-circuit/overload protected

≤ 3 V
< 5 ms

cover PBT

IEC 60947-5-2:2007 + A1:2012

39.2

LED

10

24.5

67.7

Release date: 2016-04-18 10:43 Date of issue: 2016-04-18 205349_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

M18 x 1

M12 x 1

24

4

1

Through-beam ultrasonic barrier UBE1000-18GM40A-SE2-V1-Y205349

Electrical Connection

Standard symbol/Connection:

(version E2, pnp)

Receiver:

U

Emitter:

U

Core colours in accordance with EN 60947-5-2.

Pinout

Connector V1

3

Additional Information

Obstacle size

min. obstacle size d [mm]

80

(BN)

1

(WH)

2

4

(BK)

(BU)

3

(BN)

1

(WH)

2

(BK)

4
3

(BU)

2

1

4

+U

B

Teaching input

Switching output

-U

B

+U

B
Test input
n.c.

-U

B

70

60

50

40

30

20

10

0

0 200 400 600 800 1000

d

X

distance X [mm]

with Teach-In
without Teach-In

Accessories

UB-PROG2

Programming unit

OMH-04

Mounting aid for round steel ø 12 mm or sheet 1.5 mm ... 3 mm

BF 18

Mounting flange, 18 mm

BF 18-F

Mounting flange with dead stop, 18 mm

BF 5-30

Universal mounting bracket for cylindrical sensors with a diameter of 5 ... 30 mm

V1-G-2M-PVC

Female cordset, M12, 4-pin, PVC cable

V1-W-2M-PUR

Female cordset, M12, 4-pin, PUR cable

Function

A through-beam ultrasonic barrier always consists of a single emitter and a single
receiver. The function of a through-beam ultrasonic barrier is based in the interrup­tion of the sound transmission to the receiver by the object to be detected.
The emitter sends an ultrasonic signal that is evaluated by the receiver. If the signal
is interrupted or muted by the object to be detected, the receiver switches.
No electrical connections are required between the emitter and receiver.
The function of through-beam ultrasonic barriers is not dependent on the position of
their installation. We recommend, however, to install the emitter below in the case
of vertical installations to prevent the accumulation of dust particles.

Startup and parameterising

For easy alignment of emitter and receiver towards each other, the receiver is equip­ped with an alignment aid. To activate the alignment aid, the TEACH-Input of the re­ceiver (pin 2) has to be connected to ground (-U
yellow LED indicates the strength of the received ultrasonic signal. The better the
alignment, the stronger the signal.

). The flashing frequency of the

B

Release date: 2016-04-18 10:43 Date of issue: 2016-04-18 205349_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

2