Ultrasonic sensor UB1000-18GM75-E01-V15
Technical data
General specifications
Sensing range 70 ... 1000 mm
Adjustment range 90 ... 1000 mm
Dead band 0 ... 70 mm
Standard target plate 100 mm x 100 mm
Transducer frequency approx. 255 kHz
Response delay approx. 125 ms
Indicators/operating means
Model Number
UB1000-18GM75-E01-V15
Single head system
Features
•2 switch outputs
• Selectable sound lobe width
•Program input
• Temperature compensation
• Very small unusable area
Diagrams
Characteristic response curve
Distance Y [mm]
250
flat surface 100 mm x 100 mm
200
150
100
5
0
-50
-100
-150
-200
round bar, Ø 25 mm
-250
0 200 400 600 800 1000 1200 1400 1600
Distance X [mm]
LED yellow indication of the switching state
LED red "Error", object uncertain
Electrical specifications
Operating voltage U
No-load supply current I
Input
B
0
Input type 1 program input,
Output
Output type 2 switch outputs NPN, normally open/closed
Rated operating current I
Voltage drop U
Repeat accuracy ≤ 1 %
d
e
Switching frequency f max. 3 Hz
Range hysteresis H 1 % of the set operating distance
Temperature influence ± 1.5 % of full-scale value
Ambient conditions
Ambient temperature -25 ... 70 °C (-13 ... 158 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type Connector M12 x 1 , 5-pin
Degree of protection IP67
Material
Housing brass, nickel-plated
Transducer epoxy resin/hollow glass sphere mixture; foam polyurethane,
Mass 60 g
Factory settings
Output 1 Switching point: 90 mm
Output 2 Switching point: 1000 mm
Beam width wide
Compliance with standards and
directives
Standard conformity
Standards EN 60947-5-2:2007 + A1:2012
Approvals and certificates
UL approval cULus Listed, General Purpose
CSA approval cCSAus Listed, General Purpose
CCC approval CCC approval / marking not required for products rated ≤36 V
flashing: program function object detected
in program function: No object detected
10 ... 30 V DC , ripple 10 %
≤ 50 mA
operating range 1: -U
+U
B
input impedance: > 4.7 kΩ; program pulse: ≥ 1 s
SS
... +1 V, operating range 2: +4 V ...
B
2 x 100 mA , short-circuit/overload protected
≤ 3 V
cover PBT
output function: Switch point operation mode
output behavior: NO contact
output function: Switch point operation mode
output behavior: NC contact
IEC 60947-5-2:2007 + A1:2012
Y
X
Release date: 2016-04-13 11:16 Date of issue: 2016-04-13 204533_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
wide sound lobe
narrow sound lobe
1
Ultrasonic sensor UB1000-18GM75-E01-V15
Dimensions
LEDs
4
24
M12 x 1
M18 x 1
Additional Information
Programmed switching output function
Switch output 1
(N.O.)
Switch output 2
(N.C.)
Switch point 1 -> ∞:Switch output 1, (
Switch point 2 -> ∞:Switch output 2, (
Detection of object presence
Detection of object presence
48
75
85
Object range
N.O.)
N.C.)
Electrical Connection
Standard symbol/Connections:
(version E01, npn)
U
Core colours in accordance with EN 60947-5-2.
Pinout
Wire colors in accordance with EN 60947-5-2
1 BN
2 WH
3 BU
4 BK
5 GY
(BN)
1
(BK)
4
(WH)
2
(GY)
5
(BU)
3
2
+ U
B
Switch output 1
Switch output 2
Teaching input
- U
B
1
5
4
3
(brown)
(white)
(blue)
(black)
(gray)
Release date: 2016-04-13 11:16 Date of issue: 2016-04-13 204533_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
2
Ultrasonic sensor UB1000-18GM75-E01-V15
Accessories
UB-PROG3
Programming unit
OMH-04
Mounting aid for round steel ø 12 mm or sheet 1.5 mm ... 3 mm
BF 18
Mounting flange, 18 mm
BF 18-F
Mounting flange with dead stop, 18 mm
BF 5-30
Universal mounting bracket for cylindrical sensors with a diameter of 5 ... 30 mm
UVW90-K18
Ultrasonic -deflector
V15-G-2M-PVC
Female cordset, M12, 5-pin, PVC cable
M18K-VE
Description of Sensor Functions
Programming procedure
The sensor features two switch outputs with one programmable switch point, each. Programming the switch points is done by applying the supply
voltage -U
1 s. LEDs indicate whether the sensor has recognized the target during the programming procedure.
Note:
Switching points may only be specified directly after Power on. A time lock secures the adjusted switching points against unintended modification
5 minutes after Power on. To modify the switching points later, the user may specify the desired values only after a new Power On.
Note:
If a programming adapter UB-PROG3 is used for the programming procedure, button A1 is assigned to -UB and button A2 is assigned to +UB.
Programming switch ouputs
Switch point for switch output 1
1. Place the target at the desired switch point position of switch output 1
2. Program the switch point by applying -U
3. Disconnect the Teach-In input from -U
Switch point for switch output 2
1. Place the target at the desired switch point position of switch output 2
2. Program the switch point by applying +U
3. Disconnect the Teach-In input from +U
Programming detection of object presence
1. Cover the sensor face with hand or remove all objects from sensing range
2. Apply -U
3. Disconnect the Teach-In input from -U
4. Apply +UB to the Teach-In input (red LED flashes)
5. Disconnect the Teach-In input from +U
Note: Only one switch output can be configured for detection of presence of objects. If the sensor detects an object within the maximum
detection range, the switch output switches.
(switch output 1) or +UB (switch output 2) to the Teach-In input. The supply voltage must be applied to the Teach-In input for at least
B
to the Teach-In input (corresponding yellow LED flashes)
B
to save the switch point
B
to the Teach-In input (corresponding yellow LED flashes)
B
to save the switch point
B
to the Teach-In input (red LED flashes)
B
B
B
Adjusting the sound cone characteristics:
The ultrasonic sensor enables two different shapes of the sound cone, a wide angle sound cone and a small angle sound cone.
1. Small angle sound cone
• switch off the power supply
•connect the Teach-In input wire to -U
• switch on the power supply
• the red LED flashes once with a pause before the next.
• yellow LED: permanently on: indicates the presence of an object or disturbing object within the sens-
ing range
• disconnect the Teach-In input wire from -U
2. Wide angle sound cone
• switch off the power supply
•connect the Teach-In input wire with +U
• switch on the power supply
• the red LED double-flashes with a long pause before the next.
• yellow LED: permanently on: indicates an object or disturbing object within the sensing range
• disconnect the Teach-In input wire from +U
B
and the changing is saved
B
B
and the changing is saved
B
Factory settings
See technical data.
Display
Release date: 2016-04-13 11:16 Date of issue: 2016-04-13 204533_eng.xml
The sensor provides LEDs to indicate various conditions.
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
pause
pause
3
Ultrasonic sensor UB1000-18GM75-E01-V15
During Normal operation
Proper operation
Interference (e.g. compressed air)
Programming of output 1
Object detected
No object detected
Object uncertain (programming invalid)
Programming of output 2
Object detected
No object detected
Object uncertain (programming invalid)
Red LED Yellow LED 1 Yellow LED 2
Off
On
Off
Flashes
On
Off
Flashes
On
Switching state
output 1
remains in previous
state
Flashes
Off
Off
Off
Off
Off
Switching state
output 2
remains in previous
state
Off
Off
Off
Flashes
Off
Off
Installation conditions
If the sensor is installed at places, where the environment temperature can fall below 0 °C, for the sensors fixation, one of the mounting flanges
BF18, BF18-F or BF 5-30 must be used.
In case of direct mounting of the sensor in a through hole using the steel nuts, it has to be fixed at the middle of the housing thread. If a fixation at
the front end of the threaded housing is required, plastic nuts with centering ring (accessories) must be used.
Release date: 2016-04-13 11:16 Date of issue: 2016-04-13 204533_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
4
Loading...