Pepperl Fuchs PMI80-F90-IE8-V15 Data Sheet

Inductive positioning system PMI80-F90-IE8-V15

Technical data

General specifications

Switching element function Analog current output with PNP binary NO
Object distance 0.5 ... 3 mm , recommended: 2 mm
Measurement range 0 ... 80 mm
Linearity range 1 ... 79 mm

Nominal ratings

Model Number

PMI80-F90-IE8-V15

Features

• Analog output 4 mA ... 20 mA

• Adjustable switch points

• Measuring range 0 ... 80 mm

Operating voltage U
Reverse polarity protected reverse polarity protected
Linearity error within measuring range: ± 0.8 mm

Repeat accuracy ± 0.1 mm
Resolution 125 µm
Temperature drift ± 0.5 mm (-25 °C ... 70 °C)
No-load supply current I
Operating voltage display LED green

Functional safety related parameters

MTTFd 300 a
Mission Time (T
Diagnostic Coverage (DC) 0 %

Switching output

Output type 2 switch outputs PNP, NO , reverse polarity protected ,

Operating current I
Switching window ± 1 mm
Switching hysteresis 0.4 mm
Voltage drop ≤ 3 V
Short-circuit protection pulsing

Analog output

Output type 1 current output: 4 ... 20 mA
Load resistor ≤ 400 Ω

Ambient conditions

Ambient temperature -25 ... 70 °C (-13 ... 158 °F)

Mechanical specifications

Connection type M12 x 1 connector, 5-pin
Protection degree IP67
Material

Housing ABS
Target structural steel, e. g. 1.0037, SR235JR (formerly St37-2)

Compliance with standards and
directives

Standard conformity

Standards EN 60947-5-2:2007

B

0

) 20 a

M

L

18 ... 30 V DC

within linearity range: ± 0.4 mm

≤ 40 mA

short-circuit protected
≤ 100 mA

IEC 60947-5-2:2007

Approvals and certificates

UL approval cULus Listed, General Purpose, Class 2 Power Source

CCC approval Products with a maximum operating voltage of ≤36 V do

not bear a CCC marking because they do not require
approval.

Dimensions

LED

4 mA

Button

41

2223

S2S1

M5 (2x)

S1S2

63

20 mA

M12 x 1

LED Power

83

102

Release date: 2012-05-30 16:55 Date of issue: 2012-05-30 191137_eng.xml

Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany

• Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://

1

Inductive positioning system PMI80-F90-IE8-V15

Electrical Connection

Pinout

Wire colors in accordance with EN 60947-5-2

1 BN
2 WH
3 BU
4 BK
5 GY

IE8

Additional Information

dimensions for the target object:

1

2

5
2
4

3

1

3

(brown)
(white)
(blue)
(black)
(gray)

I

+ UB

4-20 mA

Q S1
Q S2

- UB

5

4

10 V/20 mA

8

≥ 18

Linearity range

Measuring range

≥ 4

0 V/4 mA

Accessories

BT-F90-W

Damping element for F90 sensors; lateral screw holes

MH-F90

Mounting bracket for mounting of F90 sensors

V15-G-2M-PVC

Cable socket, M12, 5-pin, PVC cable

V15-W-2M-PVC

Cable socket, M12, 5-pin, PVC cable

Operating instructions

• Safety information

Warni ng

• Sensor versions

The F90 linear position measurement system is available in 2 versions.
In the PMI...-F90-IU-V1 version, the position measuring system transmits current and voltage signals pro­portional to the position of the damping element at the outputs.
The PMI...-F90-IE8-V15 version offers a current signal as well as the option of teaching in two switching
points directly at the sensor independently of one another at the press of a button, which is then indicated
on two switching outputs. Two additional LEDs indicate the output states of the two switching outputs.

Version PMI…-F90-IU-V1

Output signals: 4 mA ... 20 mA and 0 V ... 10 V

Note

Version PMI…-F90-IE8-V15

Output signals: 4 mA ... 20 mA and 2 programmable switching amplifiers

• Programming the PMI…-F90-IE8-V15

The rear of the PMI...-F90-IE8-V15 sensor has two small, slightly recessed push buttons for programming
the switching points. The buttons are marked "teach in" and S1 for switching point S1 and S2 for switching
point S2.
To teach in a switching point, proceed as follows:

- The position detection damping element must be placed at the relevant position, i.e. the switching point
that you wish to teach in.

2

This product may not be used in applications where personal safety
depends on the function of the device.
This product is not a safety component as described in EU Machinery Direc­tive.

Only the current output or the voltage output may be used. The unused output must remain
load free.

Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany

• Tel.: Germany [phone] • USA [phone] • Singapore [phone] • Internet http://

Release date: 2012-05-30 16:55 Date of issue: 2012-05-30 191137_eng.xml