Pepperl Fuchs PMI14V-F166-U-1M-V15 Data Sheet
Inductive positioning system PMI14V-F166-U-1M-V15
Technical data
General specifications
Switching element function Analog voltage output
Object distance 0.5 ... 2 mm
Measurement range 0 ... 14 mm
Nominal ratings
Model Number
PMI14V-F166-U-1M-V15
Features
•Analog output 0...10V
• Measuring range 0 ... 14 mm
• Scaleable measurement range
programmable via cable
Operating voltage U
Reverse polarity protection reverse polarity protected
Linearity error ± 0.3 mm
Repeat accuracy R ± 0.05 mm
Resolution 33 µm
Temperature drift ± 0.3 mm (With a target distance of 0.5 mm)
No-load supply current I
Functional safety related parameters
MTTFd 830 a
Mission Time (T
Diagnostic Coverage (DC) 0 %
Analog output
Output type 1 voltage output: 0 ... 10 V
Load resistor ≥ 1000 Ω
Short-circuit protection current limit
Ambient conditions
Ambient temperature -10 ... 70 °C (14 ... 158 °F)
Storage temperature -20 ... 70 °C (-4 ... 158 °F)
Mechanical specifications
Connection type Male cordset, M12 , 5-pin
Degree of protection IP65
Material
Housing Zinc die-casting, nickel-plated
Target mild steel, e. g. 1.0037, SR235JR (formerly St37-2)
Mass 75 g
Compliance with standards and
directives
Standard conformity
Standards EN 60947-5-2:2007
B
0
) 20 a
M
18 ... 30 V DC
≤ 20 mA
1 m, PUR cable, shielded
cover , PBT
IEC 60947-5-2:2007
EN 60947-5-7:2003
Dimensions
11.3 4.8
22
30
5.4
13.65
16.9
17.8
30
13.5
23
7
4 1.5
16
11
39
4
14
Release date: 2016-06-30 11:51 Date of issue: 2016-07-13 263347_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
1
Inductive positioning system PMI14V-F166-U-1M-V15
Electrical Connection
I
Pinout
Wire colors in accordance with EN 60947-5-2
1 BN
2 WH
3 BU
4 BK
5 GY
Additional Information
dimensions for the target object:
1
5
2
4
3
2
(brown)
(white)
(blue)
(black)
(gray)
+UB
Service
Service
Analogue output
-UB
1
5
4
3
8
≥ 18
≥ 2
Accessories
BT-F90-W
Damping element for sensors of type F90, F112, and F166; side hole
BT-F90-G
Damping element for sensors of type F90, F112, and F166; front hole
PMI14V-Teach
Programming unit
Information on Operation
Safety Information
This product must not be used in applications in which the safety of persons
depends on the function of the device.
Warn un g
Actuator
The linear position measurement system is optimally aligned to the geometry of Pepperl+Fuchs actuators.
Using Your Own Actuators
Generally speaking, it is possible for you to use your own actuators. The specified measurement accuracy of the sensor will be achieved only if the actuator has the following properties:
• Material: construction steel such as S235JR+AR (previously St37)
• Dimensions (L x W x H): >
• The active surface of the actuator must protrude across the entire sensor width.
Note:
The width of the actuator must be precisely 8 mm. If the width of the actuator deviates from
this value, the position values will differ.
This product is not a safety component as specified in the EU Machinery Directive.
18 mm x 8 mm x > 2 mm
Programming the 2 Scaling Positions
You can teach 2 scaling positions using the PMI14V-Teach programming unit. The program-
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
2
Release date: 2016-06-30 11:51 Date of issue: 2016-07-13 263347_eng.xml
Loading...