Pepperl Fuchs PMI14V-F166-2E2 Data Sheet
Inductive positioning system PMI14V-F166-2E2
Technical data
General specifications
Switching element function PNPDual NO
Object distance 0.5 ... 2 mm
Measurement range 0 ... 14 mm
Nominal ratings
Model Number
PMI14V-F166-2E2
Features
• Measuring range 0 ... 14 mm
• 2 programmable switch outputs
Operating voltage U
Reverse polarity protection reverse polarity protected
Voltage drop U
Linearity error ± 0.3 mm
Repeat accuracy R ± 0.05 mm
Resolution 33 µm
Temperature drift ± 0.3 mm (With a target distance of 0.5 mm)
No-load supply current I
Functional safety related parameters
MTTFd 880 a
Mission Time (TM) 20 a
Diagnostic Coverage (DC) 0 %
Switching output
Output type PNP (2 Channels)
Operating current I
Switching window position programmable, width 2 mm
Switching hysteresis 0.4 mm
Short-circuit protection pulsing
Ambient conditions
Ambient temperature -10 ... 70 °C (14 ... 158 °F)
Storage temperature -20 ... 70 °C (-4 ... 158 °F)
Mechanical specifications
Connection type 5 x 0.14 mm2 , screened 2 m PUR cable
Degree of protection IP65
Material
Housing Zinc die-casting, nickel-plated
Target mild steel, e. g. 1.0037, SR235JR (formerly St37-2)
Mass 95 g
Compliance with standards and
directives
Standard conformity
Standards EN 60947-5-2:2007
Approvals and certificates
UL approval cULus Listed, Class 2 Power Source, Type 1 enclosure
B
d
0
L
18 ... 30 V DC
≤ 3 V
≤ 20 mA
per channel 50 mA , Combined max. 80 mA
cover , PBT
IEC 60947-5-2:2007
EN 60947-5-7:2003
Dimensions
11.3 4.8
22
30
5.4
13.65
16.9
17.8
30
13.5
23
7
4 1.5
16
11
39
4
14
Release date: 2017-11-02 11:48 Date of issue: 2017-11-02 238881_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
1
Inductive positioning system PMI14V-F166-2E2
Electrical Connection
BN
GY
WH
I
BK
BU
+UB
Teach-In
S2
S1
-UB
Accessories
BT-F90-W
Damping element for sensors of type F90, F112, and F166; side hole
BT-F90-G
Damping element for sensors of type F90, F112, and F166; front hole
PMI14V-Teach
Programming unit
Information on Operation
Safety Information
This product must not be used in applications in which the safety of persons
depends on the function of the device.
Warn un g
This product is not a safety component as specified in the EU Machinery Directive.
Additional Information
dimensions for the target object:
8
≥ 18
≥ 2
Actuator
The linear position measurement system is optimally aligned to the geometry of Pepperl+Fuchs actuators.
Using Your Own Actuators
Generally speaking, it is possible for you to use your own actuators. The specified measurement accuracy of the sensor will be achieved only if the actuator has the following properties:
• Material: construction steel such as S235JR+AR (previously St37)
• Dimensions (L x W x H): >
18 mm x 8 mm x > 2 mm
• The active surface of the actuator must protrude across the entire sensor width.
Note:
The width of the actuator must be precisely 8 mm. If the width of the actuator deviates from
this value, the position values will differ.
Programming the Switching Windows
The two switching windows can be taught in using the PMI14V-Teach programming unit. The
programming unit is connected directly between the sensor and the power supply. The Teachin process is generally only possible in the first 6 minutes of the sensor being switched on. After
that point, programming is blocked and is only possible again once the power supply has been
interrupted.
The relevant positions of the switching windows that are taught in are stored in the nonvolatile
memory. The switching windows are positioned symmetrically around the configured position
in each case. The measured position is based on half of the width (center) of the damping element.
Teach-In Process
Switching the Sensor to Programming Mode
1. Connect the programming unit between the sensor and the power supply.
2. Press and hold the key on the programming unit for approx. 1.5 seconds.
>> The LED S1 on the programming unit flashes (2 Hz).
Switching window 1: width 2 mm (± 1 mm), switching output S1
Prerequisite: LED S1 is flashing.
1. Position the damping element in the required switching position.
2. Press the button again.
>> The sensor teaches in position 1. If the Teach-in process was successful, LED S1 lights up
for approx. 1.5 seconds.
Switching window 2: width 2 mm (± 1 mm), switching output S2
Prerequisite: LED S2 is flashing.
1. Position the damping element in the required switching position.
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
2
Release date: 2017-11-02 11:48 Date of issue: 2017-11-02 238881_eng.xml
Loading...