|
|
|
|
|
|
|
|
|
|
|
|
Inductive sensor |
|
|
|
|
|
NJ50-FP-E-P2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Technical Data |
|
|
|
|
|
|
|
|
|
General specifications |
|
|
|
|
|
|
|
|
|
Switching function |
|
Normally open (NO) |
|
|
|
|
|
|
|
Output type |
|
NPN |
|
|
|
|
|
|
|
Rated operating distance |
sn |
50 mm |
|
|
|
|
|
|
|
Installation |
|
non-flush |
|
|
|
|
|
|
|
Output polarity |
|
DC |
|
|
|
|
|
|
|
Assured operating distance |
sa |
0 ... 40.5 mm |
|
|
|
|
|
|
|
Reduction factor rAl |
|
0.4 |
|
|
|
|
|
|
|
Reduction factor rCu |
|
0.3 |
|
|
|
|
|
|
|
Reduction factor r304 |
|
0.85 |
|
|
|
|
|
|
|
Output type |
|
3-wire |
|
|
|
|
|
|
|
Nominal ratings |
|
|
|
|
|
|
|
|
|
Operating voltage |
UB |
10 ... 60 V |
|
|
|
|
|
|
|
Switching frequency |
f |
0 ... 100 Hz |
|
|
|
|
|
|
|
Hysteresis |
H |
typ. 3 % |
|
|
|
|
|
|
|
Reverse polarity protection |
|
yes |
|
|
|
|
|
|
|
Short-circuit protection |
|
yes |
|
|
|
|
|
|
|
Voltage drop |
Ud |
≤ |
3 V |
|
|
|
|
|
|
Operating current |
IL |
0 ... 200 mA |
|
|
|
|
|
|
|
Off-state current |
Ir |
0 ... 0.5 mA typ. 0.1 A at 25 °C |
|
|
|
|
|
|
|
No-load supply current |
I0 |
≤ |
20 mA |
|
|
|
|
|
|
Time delay before availability |
tv |
≤ |
30 ms |
|
|
|
|
|
|
Operating voltage indicator |
|
LED, green |
|
|
|
|
|
|
|
Switching state indicator |
|
LED, yellow |
|
|
|
|
|
|
|
Standard conformity |
|
|
|
|
|
|
Model Number |
|
|
|
|
|
|||
|
|
Standards |
|
EN 60947-5-2:2007 |
|
|
|||
|
NJ50-FP-E-P2 |
|
|
|
IEC 60947-5-2:2007 |
|
|
||
|
|
Ambient conditions |
|
|
|
|
|
||
|
|
|
|
Ambient temperature |
|
-25 ... 70 °C (-13 ... 158 °F) |
|
|
|
|
Features |
|
Mechanical specifications |
|
|
|
|
|
|
|
|
|
|
Information for connection |
|
A maximum of two conductors with the same core cross section |
|
||
|
• |
3-wire DC |
|
|
|
may be mounted on one terminal connection! |
|
||
|
• |
Surface mount |
|
|
|
tightening torque 1.2 Nm + 10 % |
|
|
|
|
|
Core cross-section |
|
up to 2.5 mm2 |
|
|
|||
|
• Sensing range 50 mm |
|
Minimum core cross-section |
|
without wire end ferrule 0.5 mm2 |
, with connector sleeves 0.34 mm2 |
|
||
|
|
|
|
Maximum core cross-section |
|
without wire end ferrule 2.5 mm2 |
, with connector sleeves 1.5 mm2 |
|
|
|
|
|
|
Housing material |
|
Crastin (PBTB) |
|
|
|
|
|
|
|
Sensing face |
|
PBT |
|
|
|
|
|
|
|
Degree of protection |
|
IP67 |
|
|
|
|
|
|
|
Approvals and certificates |
|
|
|
|
|
|
|
|
|
UL approval |
|
cULus Listed, General Purpose |
|
|
|
|
|
|
|
CSA approval |
|
cCSAus Listed, General Purpose |
|
Dimensions
ø 9.5
LEDs
<![if ! IE]><![endif]>40
1/2“ NPT
<![if ! IE]> <![endif]>7 |
<![if ! IE]> <![endif]>11 |
ø 5.3 |
<![if ! IE]> <![endif]>091330 eng.xml |
<![if ! IE]> <![endif]>80 |
<![if ! IE]> <![endif]>65 |
<![if ! IE]> <![endif]>2017-04-28 |
|
|
<![if ! IE]> <![endif]>issue: |
|
65 |
<![if ! IE]> <![endif]>Date of |
|
|
<![if ! IE]> <![endif]>-04-28 12:48 |
|
|
<![if ! IE]> <![endif]>Release date: 2017 |
|
|
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”. |
1 |
|
|
|
|
|
|
|
Inductive sensor |
NJ50-FP-E-P2 |
|
|
|
|
|
|
|
|
|
Electrical Connection |
|
1
L+ 4
3
L-
<![if ! IE]><![endif]>Release date: 2017-04-28 12:48 Date of issue: 2017-04-28 091330_eng.xml
2Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.