Pepperl Fuchs NJ2-11-N Data Sheet

Inductive sensor NJ2-11-N

Technical Data

General specifications

Switching function Normally closed (NC) Output type NAMUR Rated operating distance sn2 mm Installation flush Assured operating distance sa0 ... 1.62 mm

0102

Model Number

NJ2-11-N

Features

•2 mm flush

• Usable up to SIL 2 acc. to IEC 61508

Accessories

BF 11

Mounting flange, 11 mm

Actual operating distance s Reduction factor rAl 0.4 Reduction factor r Reduction factor r Output type 2-wire

Nominal ratings

Nominal voltage Uo8.2 V (Ri approx. 1 kΩ) Switching frequency f 0 ... 3000 Hz Hysteresis H 0.5 ... 3.5 typ. 2 % Current consumption

Measuring plate not detected Measuring plate detected

Functional safety related parameters

MTTFd 5887 a Mission Time (T Diagnostic Coverage (DC) 0 %

Ambient conditions

Ambient temperature -25 ... 100 °C (-13 ... 212 °F)

Mechanical specifications

Connection type cable PVC , 2 m Core cross-section 0.34 mm Housing material PVDF Sensing face PVDF Degree of protection IP68 Cable

Bending radius

General information

Use in the hazardous area see instruction manuals

Category

Compliance with standards and directives

Standard conformity

NAMUR

Standards

Approvals and certificates

FM approval

Control drawing UL approval cULus Listed, General Purpose CCC approval CCC approval / marking not required for products rated ≤36 V

0.3

0.85

304

) 20 a

Dimensions

1.8 ... 2.2 mm

≥ 3 mA ≤ 1 mA

> 10 x cable diameter

1G; 2G; 3G; 1D; 3D

EN 60947-5-6:2000 IEC 60947-5-6:1999 EN 60947-5-2:2007 IEC 60947-5-2:2007

116-0165

Release date: 2016-11-08 17:34 Date of issue: 2018-02-16 106377_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

Electrical Connection

ø11

L+

L-

Inductive sensor NJ2-11-N

Equipment protection level Ga

CE marking 0102

ATEX marking ¬ II 1G Ex ia IIC T6…T1 Ga The Ex-related marking can also be printed on the enclosed label.

Standards EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety"

Appropriate type NJ 2-11-N...

Effective internal inductivity C

Effective internal inductance L

Ambient temperature Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the

Equipment protection level Gb

CE marking 0102

ATEX marking ¬ II 1G Ex ia IIC T6…T1 Ga The Ex-related marking can also be printed on the enclosed label.

Standards EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety"

Appropriate type NJ 2-11-N...

Effective internal inductivity C

Effective internal inductance L

Maximum permissible ambient temperature T

Equipment protection level Gc (ic)

Certificate PF 13 CERT 2895 X

CE marking

Use is restricted to the following stated conditions

≤ 45 nF ; a cable length of 10 m is considered.

≤ 50 µH ; a cable length of 10 m is considered.

temperature class, and the effective internal reactance values can be found on the EC-type examination certificate.

Note:

Use the temperature table for category 1 !!! The 20 % reduction in accordance with EN 1127-1 has already

been applied to the temperature table for category 1.

Use is restricted to the following stated conditions

≤ 45 nF ; a cable length of 10 m is considered.

≤ 50 µH ; a cable length of 10 m is considered.

Details of the correlation between the type of circuit connected, the maximum permissible ambient temperature, the

amb

temperature class, and the effective internal reactance values can be found on the EC-type examination certificate.

ATEX marking ¬ II 3G Ex ic IIC T6…T1 Gc

Standards EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection category "ic" Use is restricted to the following

Effective internal inductivity C

Effective internal inductance L

The Ex-significant identification is on the enclosed adhesive label

stated conditions

≤ 45 nF ; a cable length of 10 m is considered.

≤ 50 µH ; A cable length of 10 m is considered.

Special conditions

for Pi=34 mW, Ii=25 mA, T6

for Pi=34 mW, Ii=25 mA, T5

for Pi=34 mW, Ii=25 mA, T4-T1

for Pi=64 mW, Ii=25 mA, T6

for Pi=64 mW, Ii=25 mA, T5

for Pi=64 mW, Ii=25 mA, T4-T1

for Pi=169 mW, Ii=52 mA, T6

for Pi=169 mW, Ii=52 mA, T5

for Pi=169 mW, Ii=52 mA, T4-T1

for Pi=242 mW, Ii=76 mA, T6

for Pi=242 mW, Ii=76 mA, T5

for Pi=242 mW, Ii=76 mA, T4-T1

55 °C (131 °F)

35 °C (95 °F)

20 °C (68 °F)

Equipment protection level Gc (nL)

Standard conformity EN 60079-15:2005 Ignition protection category "n"

Effective internal capacitance C

≤ 45 nF ; a cable length of 10 m is considered.

Use is restricted to the following stated conditions

Effective internal inductance Li ≤ 50 µH ; A cable length of 10 m is considered.

General The apparatus has to be operated according to the appropriate data in the data sheet and in this instruction manual.

The data stated in the data sheet are restricted by this operating instruction! The special conditions must be observed! The ATEX Directive applies only to the use of apparatus under atmospheric conditions. If you use the device outside atmospheric conditions, consider that the permissible safety parameters should be reduced.

Special conditions

for Pi=34 mW, Ii=25 mA, T6

for Pi=34 mW, Ii=25 mA, T5

for Pi=34 mW, Ii=25 mA, T4-T1

for Pi=64 mW, Ii=25 mA, T6

for Pi=64 mW, Ii=25 mA, T5

for Pi=64 mW, Ii=25 mA, T4-T1

for Pi=169 mW, Ii=52 mA, T6

for Pi=169 mW, Ii=52 mA, T5

for Pi=169 mW, Ii=52 mA, T4-T1

for Pi=242 mW, Ii=76 mA, T6

for Pi=242 mW, Ii=76 mA, T5

for Pi=242 mW, Ii=76 mA, T4-T1

55 °C (131 °F)

35 °C (95 °F)

20 °C (68 °F)

Release date: 2016-11-08 17:34 Date of issue: 2018-02-16 106377_eng.xml

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

+ 1 hidden pages

Pepperl Fuchs NJ2-11-N Data Sheet

Specifications and Main Features

Frequently Asked Questions

User Manual