PEPPERL+FUCHS NBN40-U1L-E2 Datasheet

Dimensions

6056

128

30

40

40

LED ye

LED ye

LED gn

LED gn

5.3

M20 x 1.5

5555

25

50

Germany: [phone]Pepperl+Fuchs Group

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

USA: [phone] Singapore: [phone]

www.pepperl-fuchs.com [e-mail] [e-mail]

[e-mail]

Inductive sensor

NBN40-U1L-E2

Sensor head bidirectional and rotatable

<

40 mm non-flush

<

4 LEDs indicator for 360° visibility

<

Technical Data

General specifications

Switching function Normally open (NO)

Release date: 2020-03-23 Date of issue: 2020-03-30 Filename: 214009_eng.pdf

Output type PNP

Rated operating distance s

Installation non-flush

Output polarity DC

Assured operating distance s

Actual operating distance s

Reduction factor rAl 0.39

n

a

r

40 mm

0 ... 32.4 mm

36 ... 44 mm

1

Inductive sensor NBN40-U1L-E2

Germany: [phone]Pepperl+Fuchs Group

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

USA: [phone] Singapore: [phone]

www.pepperl-fuchs.com [e-mail] [e-mail]

[e-mail]

Technical Data

Reduction factor rCu 0.37

Reduction factor r

Reduction factor r

Output type 3-wire

Nominal ratings

Operating voltage U

Switching frequency f 0 ... 100 Hz

Hysteresis H typ. 5 %

Reverse polarity protection reverse polarity protected

Short-circuit protection pulsing

Voltage drop U

Operating current I

Off-state current I

No-load supply current I

Time delay before availability t

Operating voltage indicator LED, green

Switching state indicator LED, yellow

Functional safety related parameters

MTTF

d

Mission Time (TM) 20 a

Diagnostic Coverage (DC) 0 %

Compliance with standards and directives

Standard conformity

Standards EN 60947-5-2:2007

Approvals and certificates

Protection class II

Rated insulation voltage U

Rated impulse withstand voltage U

UL approval cULus Listed, General Purpose

CCC approval CCC approval / marking not required for products rated ≤36 V

Ambient conditions

Ambient temperature -25 ... 85 °C (-13 ... 185 °F)

Mechanical specifications

Connection type screw terminals

Information for connection A maximum of two conductors with the same core cross section may be mounted on

Core cross-section up to 2.5 mm

Minimum core cross-section without wire end ferrule 0.5 mm2 , with connector sleeves 0.34 mm

Maximum core cross-section without wire end ferrule 2.5 mm2 , with connector sleeves 1.5 mm

Housing material PA/metal

Sensing face PA

Housing base plastic

Degree of protection IP68 / IP69K

Mass 225 g

Note Tightening torque: 1.8 Nm (housing)

0.75

304

0.45

Brass

B

d

L

r

0

v

i

imp

10 ... 30 V DC

≤ 2 V

0 ... 200 mA

0 ... 0.5 mA typ. 0.01 mA

≤ 20 mA

120 ms

1310 a

EN 60947-5-2/A1:2012
IEC 60947-5-2:2007
IEC 60947-5-2 AMD 1:2012

230 V

2.5 kV

one terminal connection!
tightening torque 1.2 Nm + 10 %

2

2

2

Release date: 2020-03-23 Date of issue: 2020-03-30 Filename: 214009_eng.pdf

2

1

L+

L-

4

3

Inductive sensor NBN40-U1L-E2

Germany: [phone]Pepperl+Fuchs Group

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

USA: [phone] Singapore: [phone]

www.pepperl-fuchs.com [e-mail] [e-mail]

[e-mail]

Connection

Accessories

MHW 01 Modular mounting bracket

Release date: 2020-03-23 Date of issue: 2020-03-30 Filename: 214009_eng.pdf

3