Pepperl Fuchs NBN40-L2-B3B-V1 Data Sheet
Inductive sensor NBN40-L2-B3B-V1
Technical Data
General specifications
Switching element function NO/NC programmable
Model Number
NBN40-L2-B3B-V1
Features
• 40 mm non-flush
• A/B slave with extended addressing
possibility for up to 62 slaves
• Sensor head bidirectional and rotatable
• NO/NC programmable
• Oscillator monitoring
• On/Off delay (disconnectable)
Accessories
V1-G
Female connector, M12, 4-pin, field attachable
V1-W
Female connector, M12, 4-pin, field attachable
V1-G-2M-PUR
Female cordset, M12, 4-pin, PUR cable
V1-W-2M-PUR
Female cordset, M12, 4-pin, PUR cable
MHW 01
Modular mounting bracket
MH 02-L
Mounting aid
Rated operating distance s
Installation non-flush
Output polarity AS-Interface
Assured operating distance sa0 ... 32.4 mm
Reduction factor r
Reduction factor rCu 0.3
Reduction factor r
Slave type A/B slave
AS-Interface specification V3.0
Required master specification ≥ V2.1
Nominal ratings
Operating voltage UB26.5 ... 31.9 V via AS-i bus system
Switching frequency f 0 ... 50 Hz
Hysteresis H typ. 5 %
Reverse polarity protection reverse polarity protected
No-load supply current I
Time delay before availability t
Operating voltage display LED, green
Switching state indication LED, yellow
Fault indication LED, red
Functional safety related parameters
MTTFd 1330 a
Mission Time (T
Diagnostic Coverage (DC) 0 %
Ambient conditions
Ambient temperature -25 ... 70 °C (-13 ... 158 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type Connector M12 x 1 , 4-pin
Housing material PA
Sensing face PA
Protection degree IP69K
Mass 210 g
Compliance with standards and directives
Stan dard conf ormit y
Sta ndar ds
Approvals and certificates
UL approval cULus Listed, General Purpose
CSA approval cCSAus Listed, General Purpose
CCC approval CCC approval / marking not required for products rated ≤36 V
0.3
Al
0.75
304
) 20 a
M
Dimensions
40 mm
n
≤ 25 mA
0
≤ 1000 ms
v
EN 60947-5-2:2007
IEC 60947-5-2:2007
LED greenLED yellow/red
4
28
LED green
67
LED yellow/red
7
M12 x 1
Release date: 2013-07-10 09:41 Date of issue: 2013-07-10 226321_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
Electrical Connection
40
40
5.5
46
60
1
3
(+)
(-)
ø 5.5
30
20
1
Inductive sensor NBN40-L2-B3B-V1
Pinout
1
2
4
3
Programming Instructions
Adress 00 preset, alterable
via Busmaster
or programming units
IO-Code 0
ID-Code A
ID1-Code 7
ID2-Code E
Data bit
Bit Function
D0 Switching state
D1 not used
D2 Oscillator monitoring
D3 not used
Parameter bit
Bit Function
P0 ON / Off delay
activated* / deactivated
P1 Switching element function
NO* / NC
P2 not used
P3 not used
*
Standard setting
Indication depending on the operation mode
Symptoms green LED
(POWER)
red LED
(FAULT)
Data bit
D2
normal operation on off 1
Oscillator defect flashing flashing 0
no communication off on 1
On/off delay:
Object distance
+ Hys.
S
n
1 S
n
P0 = 0
P1 = 1
P0 = 1
P1 = 1
P0 = 0
P1 = 0
P0 = 1
P1 = 0
H
L
H
L
H
L
H
L
Data bit D0
Data bit D0
Data bit D0
Data bit D0
t
t0 + 15 ms t1 + 15 ms t
0
t
1
2
t2 + 15 ms t
t3 + 15 ms
3
time
time
time
time
time
The on/off delay is preset and switched on (P0=1). On delay approx.15 ms, when P0=1 and NO function (P1=1). Off delay
approx.15 ms, when P0=1 and NC function (P1=0).
Release date: 2013-07-10 09:41 Date of issue: 2013-07-10 226321_eng.xml
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
2
Loading...