Pepperl Fuchs KFD2-HLC-Ex1.D.2W Datasheet

HART Loop Converter

KFD2-HLC-Ex1.D.2W

7
8+
9-

14+
15-

13

20+
21-

19

Zone 2

Div. 2

I

II

10
11
12
16
17
18

24 V DC

23+
24-

22

Power Rail

24 V DCERR

HART

+

IV

V

III

Zone 0, 1, 2
Div. 1, 2

HART

+

-

HART

+

-

+

­HART

-

mA

mA

mA

mA

V

+

-

V

+

-

V

1+

2+

3-

4

5

6

250 Ω

Germany: [phone]Pepperl+Fuchs Group

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

USA: [phone] Singapore: [phone]

www.pepperl-fuchs.com [e-mail] [e-mail]

[e-mail]

KFD2-HLC-Ex1.D.2W

1-channel isolated barrier

<

24 V DC supply (Power Rail)

<

HART field device input with transmitter power supply

<

Usable as signal splitter (1 input and several outputs)

<

2 relay contact outputs (change-over contacts)

<

3 analog outputs 4 mA ... 20 mA

<

Sink and source mode output

<

Configurable by keypad

<

Function

This isolated barrier is used for intrinsic safety applications. It is a HART loop converter that provides power to transmitters or can be connected to
existing HART loops in parallel.
It is able to evaluate up to four HART variables (PV, SV, TV, QV). Of those four HART variables, the data contained in any three of them can be
converted to three different 4 mA ... 20 mA current signals. These loop signals can be connected to display devices or analog inputs on the
process control system/ control system.
In addition to the current outputs, two form C changeover relay contacts are available and can be programmed to operate at trip values from the
HART variables.
The unit is easily programmed by the use of a keypad located on the front of the unit or with the PACTware™ configuration software.
For additional information, refer to the manual and www.pepperl-fuchs.com.

Connection

Technical Data

General specifications

Signal type Analog input

Supply

Connection Power Rail or terminals 23+, 24-

Rated voltage U

Rated current I

Power dissipation 2.5 W

Power consumption 3.1 W

HART signal channels (intrinsically safe)

Release date: 2020-09-23 Date of issue: 2020-09-23 Filename: 261918_eng.pdf

19 ... 30 V DC

r

approx. 130 mA at 24 V DC

r

1

HART Loop Converter KFD2-HLC-Ex1.D.2W

Germany: [phone]Pepperl+Fuchs Group

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

USA: [phone] Singapore: [phone]

www.pepperl-fuchs.com [e-mail] [e-mail]

[e-mail]

Technical Data

Conformity HART field device input (revision 5 to 7)

Interface

Programming interface programming socket

Input

Connection side field side

Connection terminals 1, 2, 3, 4, 5, 6

Open circuit voltage/short-circuit current typ. 24 V / 28 mA

Input resistance 250 Ω , 5 % (terminals 2, 3 and with jumper on 5, 6)

Available voltage ≥ 15.5 V at 20 mA, short-circuit protected

Output

Connection side control side

Connection output I: terminals 10, 11, 12, output II: terminals 16, 17, 18

Output I, II

Output signal relay and LED yellow

Mechanical life 107 switching cycles

Energized/De-energized delay approx. 20 ms / approx. 20 ms

Output III, IV, V

Output signal analog

Current range 4 ... 20 mA , (source or sink mode)

Load max. 650 Ω , source mode

Voltage range 5 ... 30 V , sink mode from external supply

Fault signal downscale I ≤ 2 mA, upscale I ≥ 21.5 mA (acc. NAMUR NE43) or hold measurement

Other outputs HART communicator on terminals 22, 24

Collective error message Power Rail and LED red

Transfer characteristics

Output III, IV, V

Resolution max. 2 µA

Accuracy < 20 µA, 10 µA typ.

Influence of ambient temperature < ± 2 µA/K

Duration of measurement/Response delay HART message acquisition time plus 100 ms

Relay programmable either for fault or trip value (with direction, hysteresis and delay)

Galvanic isolation

Output I/II functional insulation acc. to IEC 62103, rated insulation voltage 250 V

Output I, II/other circuits reinforced insulation acc. to IEC 62103, rated insulation voltage 300 V

Output III/IV/V/power supply functional insulation acc. to IEC 62103, rated insulation voltage 50 V

Indicators/settings

Display elements LEDs , display

Control elements Control panel

Configuration via operating buttons

Labeling space for labeling at the front

Directive conformity

Electromagnetic compatibility

Directive 2014/30/EU EN 61326-1:2013 (industrial locations)

Low voltage

Directive 2014/35/EU EN 61010-1:2010

Conformity

Electromagnetic compatibility NE 21:2006

Degree of protection IEC 60529:2001

Ambient conditions

Ambient temperature -20 ... 60 °C (-4 ... 140 °F)

Release date: 2020-09-23 Date of issue: 2020-09-23 Filename: 261918_eng.pdf

output III: terminals 7, 8, 9, output IV: terminals 13, 14, 15, output V: terminals 19, 20,
21

value

eff

rms

eff

via PACTware

2