Penta KB Power KBPC-240D, KBAC-27D, KBAC-24D Installation Instructions Manual

DESCRIPTION

The Run-Stop-Jog Switch provides a momentary jog speed which can be used to index a machine into position. The switch contains
three (3) positions:

1. “Run” – The switch is placed in this position when the control output is to be set using the Main Speed Potentiometer.

2. “Jog” – Used to provide a low speed output. This position is spring loaded so the switch must be held. The jog speed can be changed
using the JOG trimpot located on the PC board.

3. “Stop” – Used as a resting position when the Jog function is used. The motor will stop when in this position.

MOUNTING

WARNING! Make sure that the AC line is disconnected before

installing the Auto/Manual Switch assembly.

1. KBPC-240D – Remove the Rubber hole plug in the Run-Stop-Jog position
by unscrewing the retainer nut on the inside cover.

KBAC-24D and KBAC-27D – Remove the rubber hole plug from any avail­able position by unscrewing the retainer nut on the inside cover.

2. Install the Run-Stop-Jog Switch assembly into the front cover making sure
the key in the hole lines up with the keyway in the switch bushing. Be sure
the hex nut supplied is installed at the base of the switch bushing before
inserting switch into the KBPC cover.

KBAC-27D Note: Use the Run-Stop-Jog label that is provided, to cover
the text around the hole.

3. Install the rubber switch boot with integral hex nut over switch lever. Switch should be in the stop position to facilitate installation. Also, the
switch bushing threads should protrude no more than 1/4” (6.4 mm) or no less than 1/10” (2.6 mm) through the front cover for proper
installation. Tighten the switch boot so that the bottom seals against the cover label. Do not over tighten.

WIRING

1. Using long nose pliers, carefully remove the orange Main Speed Potentiometer wire from the “P2” terminal on the PC board. (Rock terminal
back and forth to facilitate removal.) Install this orange potentiometer wire onto the vacant terminal on the Run-Stop-Jog switch.

2. Install the gray wire from the Run-Stop-Jog switch onto the “P2” terminal on the PC board.

3. Install the green wire from the Run-Stop-Jog switch onto the “Jog” terminal on the PC board.

INSTALLATION INSTRUCTIONS

RUN-STOP-JOG SWITCH Part No. 9340A

for Model KBPC-240D, KBAC-24D, and KBAC-27D

FIGURE 1 – MOUNTING

SAFETY WARNING! Please read carefully before proceeding.

This product should be installed and serviced by a qualified technician, electrician, or electrical maintenance person familiar with its opera­tion and the hazards involved. Proper installation, which includes wiring, mounting in proper enclosure, fusing or other overcurrent protec­tion, and grounding can reduce the chance of electrical shocks, fires, or explosion in this product or products used with this product, such
as electric motors, switches, coils, solenoids, and/or relays. Eye protection must be worn and insulated adjustment tools must be used
when working with control under power. This product is constructed of materials (plastics, metals, carbon, silicon, etc.) which may be a
potential hazard. Proper shielding, grounding and filtering of this product can reduce the emission of radio frequency interference (RFI)
which may adversely affect sensitive electronic equipment. If further information is required on this product, contact the Sales Department.

This control contains electronic Start/Stop circuits that can be used to start and stop the control. However, these circuits are never to be
used as safety disconnects since they are not fail-safe. Use only the AC line for this purpose.

Be sure to follow all instructions carefully. Fire and/or electrocution can result due to improper use of this product.

It is the responsibility of the equipment manufacturer and individual installer to supply this Safety Warning to the ultimate end user of this
product.

!

A COMPLETE LINE OF MOTOR DRIVES

!

RUBBER BOOT

SWITCH BUSHING

FRONT COVER

HEX NUT

NYLON SPACER

SWITCH BODY

TM

KB ELECTRONICS, INC.

12095 NW 39th Street, Coral Springs, FL 33065-2516 • [phone] • Fax [phone]
Outside Florida Call Toll Free [phone] • E-mail – [e-mail]
www.kbelectronics.com

(A40061) – Rev. B – 6/2003

FIGURE 2A
MODEL: KBPC-240D
RUN-STOP-JOG SWITCH
CONNECTION DIAGRAM

FIGURE 2B
MODEL: KBAC-24D
RUN-STOP-JOG SWITCH
CONNECTION DIAGRAM

FIGURE 2C
MODEL: KBPC-27D
RUN-STOP-JOG SWITCH
CONNECTION DIAGRAM

INSTALLATION INSTRUCTIONS

RUN-STOP-JOG SWITCH Part No. 9340A

for Model KBPC-240D, KBAC-24D, and KBAC-27D

GRAY (P2)

GRAY (P2)

GREEN (JOG)

RUN-STOP-JOG SWITCH

(BACK VIEW)

KBAC-24D (2G) PC BOARD

VIOLET (P3)

ORANGE

WHITE (P1)

MAIN SPEED POTENTIOMETER

KBPC-240D PC BOARD

VIOLET (P3)

ORANGE

WHITE (P1)

MAIN SPEED POTENTIOMETER

(BACK VIEW)

(BACK VIEW)

JOG TRIMPOT

P1P2P3

COM JOG

JOG

P3

P2

DECEL

P1

MAX

MIN DECEL BOOST

ACCEL

JOG TRIMPOT

JOG

J6

FIX
BOOST

JOGCL

ADJ

RUN-STOP-JOG SWITCH

(BACK VIEW)

VIOLET (P3)

WHITE (P1)

GRAY (P2)

RUN-STOP-JOG SWITCH

(BACK VIEW)

GREEN (JOG)

ORANGE

MAIN SPEED POTENTIOMETER

(BACK VIEW)

GREEN (JOG)

REV STOPJOG

FWD

KBAC-27D PC BOARD

JOG TRIMPOT

P1

P2P3

BOOSTMIN

DECELACCEL JOGCL