Congratulations on the purchase of your new Kreepy Kadet, the inground pool cleaner from
Pentair Pool Products. You’ll soon see that Kreepy Kadet really is the easy way to keep your inground
pool clean. First, however, you’ll have to install Kreepy Kadet and perhaps make some minor
adjustments. This manual covers the steps needed to install and adjust Kreepy Kadet.
Contents
Warranty Terms & Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
I. Pool Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
II. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
III. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
IV. Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
V. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
VI Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
VII. Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
VIII. Parts & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Before you begin to install Kreepy Kadet in your pool, please record its serial number in the space
below. This way, if you need to refer to the serial number in the future, it will be readily available.
The diagram on page 4, Figure1shows where the serial number is located.
Kreepy Kadet Serial Number: ___________________________________________
Activate Kreepy Kadet’s Warranty
You will also need to record the serial number on the warranty registration card found inside this
manual. Complete and return the card to activate Kreepy Kadet’s 1-year limited warranty. The
complete warranty is printed on the inside front cover of this installation and operation manual.
Please review it thoroughly so you are familiar with the terms of your warranty coverage.
Customer Helpline
If you have questions about your Kreepy Kadet, check the instructions in this manual first. If you
still have a question, call your Pentair Pool Products, Inc. dealer or call our Customer Helpline
at 1-800-443-5711. Please have your Kreepy Kadet serial number ready when you call.
Warranty Note
Cleaners purchased in the United States of America from entities outside the United States do not
qualify for any United States programs including warranty, trade-in, or rebate programs.
I. Preparation of Your Pool
Before assembling and installing your cleaner, your pool should be clean and algae-free so as not to
inhibit the cleaner’s traction. If necessary, make the following preparations before proceeding:
1. Chemically balance the pool water.
2. Brush pool and let the debris settle.
3. Hand vacuum thoroughly.
4. Clean filter and pump strainer basket.
II. Assembly and Installation
R e m ove the cleaner and all of its parts from the box and ch e ck to make sure that all components we re
i n cl u d e d. Refer to Fi g u re 1.
Components Check List
Figure 1
11. Kreepy Kadet
12. Weighted Bumper Strap
13. Step Deflector
14. Float
15. Hose Weight
4.
16. Valve Cap
17. Automatic Regulator Valve
18. Threaded Compression Adapter
19. Guide Wheel
5.
10. Pleated Seal
11. Eyeball Diverter with Outer Ring
12. Skirt
6.
7.
1 3 . Hose – 32 ft. total length
(not show n )
8.
Step 1. Attach The Seal
To install the seal locate the words “This Side
Up” and face them towards the main body, slip
the seal over the foot pad – (fl at side dow n
t owa rds pool floor) – and pull ge n t ly until it
s e ats itself on the other side in its gro ove as
illustrated in Figure 2. Seal must be installed
flat side down, pleated side up. Once in place,
the seal should rotate and turn freely.
Figure 2
1.
Serial Number
3.
11.
9.
10.
Main
Body
2.
12.
Pleated Seal
in Groove
Foot Pad
The seal is not reversible. The raised pleats on
the Pleated seal must face upward. The flat side
of the seal should face down to rest against the
pool surface.
Pleats of
Pleated Seal
The fl at side of seal faces down to rest on the pool’s surfa c e.
Step 2. Attach The Skirt
Kreepy Kadet’s skirt is held in place with straps. Position
the cleaner so it is standing up with the tubes at 45 degrees
with the swivel head pointing away from you. See Figure 3.
Position the skirt so the straps wrap into the grooves on the
sides of the main body and away from you. Pull the left tee
shaped end of the strap so it slides into the last slot on the
back of the main body. Repeat these steps for the right strap.
IMPORTANT: The left strap must be fitted first for the
proper fit of the skirt.
Step 3. Attach The Guide Wheel
Slide the guide wheel over the top of the swivel head and
down over the guide wheel holder located at the top of
the main body. Snap the guide wheel over the ridge on the
guide wheel holder. See Figure 4. Ensure that the flat side
of the guide wheel center hub is facing up. Once in place,
the ring should spin freely.
Step 4. Attach The Bumper Strap
I n s e rt the bottom end of the bumper strap (end closest to the
bumper weight) into the slot provided on the main body.
I n s e rt the top end of the bumper into the slot provided in the
swivel head. See Figure 5.
Figure 3
Groove for
Skirt Strap
Swivel Head
DriveTubes
Figure 4
Guide Wheel
Swivel Head
Figure 5
Main Body
Skirt
Detail
Strap Tee
End
Slot for
Skirt Strap
Skirt
Swivel Head
Main Body
Seal
Guide Wheel
Holder
Main Body
Bumper
Weight
Step 5. Attach The Dive Float
Kreepy Kadet’s float snaps into slots on the top of the main housing. The triangular ends on the arms of
the float slide into the slots. The tip of the triangular end must slide through the opening at the end of
the slot. Keep pushing the triangular ends of the float arms into the slots until the notch on the bottom
of the triangular ends clip into place. See Figure 6. Important: Do not push on the float as you try to
snap the triangular ends into their slots or the float arm may snap. Hold the float arm just above
the triangular ends when snapping them in place.
Step 6. Assemble The Hose And
Attach The Hose Weight
The Kre epy Kadet hose comes in sections wh i ch
must be assembl e d. Yo u ’ll need enough sections
to re a ch from wh e re Kre epy Kadet is connected,
to the fa rthest part of your pool, plus one section.
You will also have to at t a ch hose weights to the hose t o
n e u t ra l i ze the hose’s bu oya n cy in wat e r. The number
of hose weights re q u i red is determined by the maximu m
d epth of your pool. The deeper your pool, the more we i g h t
is needed. The number of hose we i g h t s ap p ro p ri ate fo r
your pool is explained in Table A .
Twist and push the female ends onto the male ends
after dipping the ends into the pool to wet them.
See Fi g u re 7. Continue until yo u ’ve connected all the
sections yo u n e e d. After connecting the hose we i g h t s
to the hose as described in “ Table A,” then connect
the hose to Kreepy Kadet. See Figure 8.
One of the hose sections has 2 female ends and a hose protector. This section should be fitted last
and attached to the pool’s vacuum connection in the skimmer.
Figure 6
Float
Guide Wheel
Swivel Head
Detail
Triangular Ends
Seal
Main Body
Notch
Detail
Float Arm
Main Body
Notch
TABLE A
Pool Depth Weight Placement
Less than 7 feet No Weights Used
More than 7 feet, 1 weight: 6 feet from the
but less than 12 feet cleaner's swivel head
Figure 7
Slot
Male Hose End Female Hose End
Your fully assembled cleaner should look like this:
III. Installation
The automatic reg u l ator va l ve automat i c a l ly adjusts to ch a n ges in
the amount of water fl ow to provide the cleaner with the powe r
n e c e s s a ry to ensure proper cleaning perfo rm a n c e.
1. Turn the pool pump off.
2. Close the main drain and all suction lines, except
the line from the skimmer to which your cleaner
will be connected.
3. Remove the skimmer basket.
4. Screw the threaded compression adapter into the
vacuum connection in the bottom of the skimmer.
See Figure 9. NOTE: Use two wraps of Teflon
tape around the threads of the adapter to ensure
easy removal. (If the vacuum connection in the
bottom of the skimmer is not threaded, use a 2 inch
hose cone adapter. See Figure 9. The hose cone is
not included with your cleaner, but can be purchased
from your Pentair Pool Products Dealer.)
5. Press the automatic regulator valve into the threaded
compression adapter. See Figure 10. The end of the
va l ve that is marked “ at t a ch hose this end” must point up.
6 . Place the cleaner into the pool and allow it to sink to the
fl o o r. Continue to feed the hose down into the pool until
it is completely filled with water and purged of air.
7. Insert the hose through the skimmer opening, and
push it onto the automatic regulator valve.
See Figure 10.
Figure 8
Female End of a
Male/Female Hose
Section
NOTE: The hose length illustrated is not
representative of actual size. You will need
to use more sections than shown.
Swivel Head
Hose Weight
(If needed)
6'
Figure 9
Automatic
Regulator Valve
Threaded
Adapter
2'' Hose Cone
(not included)
Figure 10
Hose
through
Skimmer
Opening
Automatic
Regulator
Valve
Threaded
Compression
Adapter
(or 2'' Hose Cone)
Female /Female Section
to be added last
Attach Hose This End
Screw (or press) into
bottom of skimmer
Top of Skimmer
Optional Vacuum Line Installation
Vacuum Line Installation With Automatic Regulator Valve in Skimmer.
We recommend the use of the automatic reg u l ator va l ve to balance water fl ow between Kre epy Kadet and
the skimmer. When attaching Kreepy Kadet to a dedicated vacuum line, the automatic regulator valve
should be installed in the skimmer.
1. Turn the pool pump off.
2. Close the main drain and all suction lines, except the
skimmer and the vacuum line to which the Kreepy
Kadet will be connected.
3. Thread the snap-lock wall fitting into the end of the dedicated suction line. Then insert the
male end of the 45° hose connector into the snap-lock fitting. See Figure 11.
NOTE: Use t wo wraps of Te flon tape around the thre a d s to ensure easy removal.
NOTE:You will have to remove the female/female hose section in this installation.
4. Insert the male hose end of the last hose section into the 45° hose connector or directly into
the snap - l o ck wall fi t t i n g. R e m i n d e r : Do not use
the fe m a l e / female hose section in this installat i o n .
See Fi g u re 11.
5. Screw the threaded compression adapter into the
vacuum connection in the bottom of the skimmer.
NOTE: Use two wraps of Teflon tape around the
threads to ensure easy removal. If the opening in
the bottom of the skimmer is not threaded, use a
2'' hose cone, the 2'' hose cone is not provided but
can be purchased from your Pentair Pool Products
dealer.
6. To prevent water from flowing through the top of the
automatic regulator valve, fasten the valve cap onto
the top of the regulator valve. This activates the
regulator valve and assures that an accurate amount
of water (15 gpm) will flow through the vacuum
line and the Kreepy Kadet. Without the valve cap,
the automatic regulator valve and the cleaner will
not function properly. See Figure 13.
7. Press the automatic regulator valve into the
threaded compression adapter. See Figure 13.
Accessories NOT PROVIDED:
Snap-Lock Wall Fitting
(Part #K3500)
45º Hose Connector
(Part #K12078)
Figure 11
Snap-Lock Vac Fitting
45° Hose
Connector
M/F Hose
Section
Figure 12
Automatic
Regulator Valve
Threaded
Adapter
2'' Hose Cone
(Not included)
Figure 13
Automatic
Regulator
Valve
Threaded
Compression
Adapter
(or 2'' Hose Cone)
Attach Hose This End
Screw (or press) into
Top of Skimmer
Thread Snap-Lock
into Dedicated
Suction line in
Pool Wall
bottom of Skimmer
Valve
Cap
IV. Adjustments
After completing the installat i o n , t u rn the pool pump on. Your Kre epy Kadet should be moving about the
pool at ap p rox i m at e ly 8-12 feet per minu t e. A l l ow the pump to run for a couple of minutes to allow air to
cy cle out of the system. Check each of the fo l l owing initial adjustments to your Kre epy Kadet at this time.
Hose Length
IMPORTANT: The pump must be on when you check the hose length. The hose contracts when the
pump is operating and will look longer when the pump is off.
With the cleaner operating, position it at the furthest point of the pool from where it’s attached. (It is
easy to position it in the pool by moving it about with your pool pole and brush.) The hose should be
long enough to reach to the end of the pool, plus one hose section. If necessary, remove extra hose
sections from the center portion of hose. Removing center hose sections avoids having to disturb the
hose weight placement. Save extra hose sections for use as needed for replacement.
Return Line Water Flow
IMPORTANT: The water flow from your return line can push the cleaner’s hose and affect its
performance. It may cause the cleaner to steer away from the end of the pool where the return line is
located, or it may cause it to remain in one section of the pool. To correct this, use the eyeball diverter
included with your cleaner.
To install the eyeball diverter:
• First make sure your pool pump is off. Remove the original eyeball diverter from the return
line at the pool by unscrewing the lock ring.
• Replace the original eyeball diverter with the Kreepy Kadet’s eyeball diverter.
• Replace the lock ring and tighten. Make sure the opening of the eyeball diverter points in the
proper direction before tightening fully. See “Eyeball Diverter Position.”
Figure 14
Eyeball Diverter
Wire Diverter (optional)
Lock (Retaining)
Ring
Eyeball
Diverter
Eyeball
Fitting
Pool Deck
Pool
Wall
Return
Line
IMPORTANT: The eyeball diverter must fit snugly into the eyeball fitting. Some eyeball fittings,
like Aqua Leader or Olympic, may be too large for the eyeball diverter. In this situation, use the outer
ring supplied with your Kreepy Kadet to adjust for the discrepancy in size.
• S n ap the outer ring onto the eyeball dive rter and position it in the fi rst gro ove as shown in Fi g u re 15.
• I n s e rt the eyeball dive rter/outer ring assembly into the eyeball fitting in the re t u rn line. See Fi g u re 15.
• Install the lock (retaining) ring and tighten. See Figure 15.
Eyeball Diverter Positions
Position the diverter opening to redirect the return line water flow so it does not interfere with the
cleaner’s movement.
Common Diverter Positions are:
• Flow directed downward.
• Flow directed along the tile line , (side of pool along water line).
• Flow directed against cleaner’s hose.
1. To help cleaner get out of difficult areas.
2. To prevent cleaner from getting into difficult areas.
If the Eyeball or Eyeball with outer ring do not fit your pool, use the Wire Diverter accessory available
for purchase from your dealer.
After installing the eyeball diverter, turn the pool pump on. Your cleaner should begin moving across
the pool floor vacuuming up debris in its path.
Figure 15
Outer Ring
Eyeball Diverter
Snap into
this Groove
Eyeball
Diverter with
Outer Ring
Attached
Pool Deck
Eyeball
Fitting
Lock (Retaining) Ring
Pool Wall
Return
Line
V. Troubleshooting
Because of the individual characteristics of your pool, some additional adjustments may be required to
get the best performance from your Kreepy Kadet.
If there seems to be a problem, check these common causes of cleaner problems. If you still need help,
call your pool professional or call our Customer Helpline at 1-800-443-5711.
– Is bottom main drain closed? Close drain
– Is filter clean? Clean filter
– Is pump strainer basket clean? Clean basket
– Is debris blocking the bottom of the cleaner? Remove debris
– Are there any leaks in the hose? Replace leaky section
– Is automatic regulator valve free of debris? Clean valve
If Kreepy Kadet is not moving or not pulsating.
• Check to ensure that the main drain and all suction lines are closed, except for the suction line
to which the cleaner is attached.
• Check for debris in the filter or pump basket.
• Check for debris in the cleaner’s flapper. See page 14 for instructions.
• Pool pump and filter system may be too small (incapable of providing 14 gallons per minute
of water flow). Consult your pool professional.
If Kreepy Kadet slows or stops and air bubbles enter the pool at the return line.
Find and correct the air leak that is causing the pump to lose its prime:
• Check the hose to ensure there are no leaks.
• Check the vacuum connection. It should be submerged so no air enters the system.
• Check the pump basket lid for looseness, cracks, worn or missing O-rings. If you need
assistance, contact your pool professional.
If Kreepy Kadet stays in one end of the pool.
• Check the return line water flow and re-direct as necessary with an eyeball diverter.
• Check that the hose is long enough to reach to the farthest end of the pool, plus one section.
If Kreepy Kadet stays on the main drain.
• Check to ensure that the main drain is closed.
• Check to ensure that a main drain grate is installed.
• If main drain is not flush with the pool floor, consult a pool professional.
If Kreepy Kadet pulls air from, or remains at, the water surface.
• Check to ensure the dive float mechanism is securely attached.
• Check automatic regulator valve for its proper installation and ensure it is not
clogged with debris.
• Make sure the water level is at least 3 inches below the pool deck.
If Kreepy Kadet stays at the shallow end steps.
• Check the return line water flow, it may be forcing Kreepy Kadet into the steps, and redirect as
necessary with an eyeball diverter.
• C h e ck the automatic reg u l ator va l ve to ensure it is pro p e rly installed and not cl ogged with deb ri s .
• C h e ck to ensure the guide wheel is at t a ched corre c t ly.
• Install the optional step deflector (provided with your Kre epy Kadet). Un-clip the bumper strap
f rom the main body and sw ivel head. See Fi g u re 5 on page 5. Slide the bumper strap thro u g h
the two slots on the step defl e c t o r. See Fi g u re 16. Ke ep sliding the step deflector towards
the weight on the end of the bumper s t rap until it snaps in place. See Fi g u re 17. Follow the
instructions on page 5 to reinstall the bumper strap with the step defl e c t o r.
NOTE: The step deflector can not be used in vinyl liner pools.
If Kreepy Kadet tracks in a repetitive pattern.
• Check the swivel on the top of the cleaner. It should turn freely.
• Check the return line water flow and redirect as necessary with an eyeball diverter.
See page 10 “Eyeball Diverter Positions.”
• Check the hose to ensure it has not become bent or kinked. It only takes one bent or kinked
hose section to hinder the cleaning coverage. One way to check for kinks in your hose is to
lay each section flat on your pool’s deck (or other flat surface). The hose should be perfectly
straight and flat. Do not coil the hose when taking your cleaner out of the pool because it
will retain the coil shape, forming a bend or kink.
• C h e ck the position of the dive fl o at. It must be lined up with the center of the main body and
sw ivel head. If it is bent to one side, it will cause the cleaner to continu a l ly turn in that dire c t i o n .
Figure 16
Bumper Strap with
Weight
Figure 17
Bumper Strap
Step Deflector
Step Deflector
Step Deflector
Snapped in Place
Bumper Weight
If Kreepy Kadet is moving too fast.
•
In most pools, the automatic reg u l ator va l ve supplies Kre epy Kadet with the proper amount of wat e r
fl ow. However, if used with an especially powerful pool pump, the valve can be overpowered.
• To slow Kre epy Kadet dow n , a manual by-pass va l ve (Pa rt #K12094) accessory is ava i l able fo r
purchase from your Pentair Pool Products dealer. This manual by-pass can be adjusted to
achieve the recommended cleaner speed of 8 to 12 feet per minute.
• To decrease the speed of Kre epy Kadet, s i m p ly re m ove the in-line va l ve cone from the bottom o f
the automatic reg u l ator va l ve and replace it with the manual by-pass as shown in Fi g u re 18.
• P ress the automatic reg u l ator va l ve back into the threaded compression adapter in the skimmer
(or 2'' hose cone if used). The end of the va l ve that is marked “ at t a ch hose this end” mu s t
point up.
• Adjust the manual by-pass while Kre epy Kadet is ru n n i n g. Place your hand into the skimmer
and turn the by-pass adjuster one click at a time until the desired speed of 8-12 feet per minute
is reached. See Figure 19.
If Kreepy Kadet gets stuck under your pool ladder.
• Install a Ladder Guard according to the instructions contained in the packaging. This accessory
is available from your pool professional.
If Kreepy Kadet is still hampered by the unique characteristics of your pool, regardless of the
adjustments we’ve provided:
• Consider “ Th ru s t e r,” ( Pa rt #K3370) the Kre epy Kadet accessory that aids random pat t e rn
c ove rage by automat i c a l ly repositioning the hose to help free the cleaner from obstacl e s .
Thruster keeps Kreepy Kadet out of tight spots in difficult-to-clean or uniquely-shaped pools.
Ask your Pentair Pool Products dealer about this accessory.
Figure 18
Automatic
Regulator
Valve
Press on
Manual By-pass
Pull off
In-Line Valve Cone
Figure 19
Automatic Regulator Va l ve with Manual By-pass
Manual By-pass
Fully Closed
Manual By-pass
Fully Open
To Remove Debris From The Flapper.
I M P O RTA N T: The pool pump must be off
b e fo re re m oving the cleaner from the pool.
• Sometimes debris may clog the
bottom of the cleaner and prevent
flapper movement or restrict flow.
The flapper is located inside the
main body and must move freely
at all times.
• You can see the flapper through the
opening in the baffle plate when
you turn the cleaner upside down,
as shown in Figure 20. Jiggle the
flapper with your finger or flush
the cavity with a hose to force
out a ny deb ris lodged inside the
main body.
• If debris is still lodged inside, you
must remove the flapper. First, lift
the lip of the foot pad up and insert
a flat-headed screwdriver along side one of the two tabs found on either side of the baffle plate.
See Figure 21. Push the tab inward with the screwdriver until the baffle plate releases. Place a
finger into the center opening of the baffle plate and pull up until it pops out. Then pull the
fl apper out. N OT E : You should be able to do this without taking the foot pad off.
• Once the debris is dislodged, insert the flapper back into the main body and snap the baffle plate
back into position. Be sure that it is securely in place. See Figure 21.
Figure 20
BOTTOM VIEW OF CLEANER
Flapper is
inside
Baffle
Plate
Figure 21
Baffle Plate
Flapper
Foot Pad
Pleated
Seal
Main Body
Foot Pad
(not necessary to remove)
VI. Maintenance
Kreepy Kadet requires almost no maintenance. Visually inspect your Kreepy Kadet from time to time to
make sure that:
• The flapper is moving freely and is not obstructed by debris.
• The footpad is not excessively worn. When the traction pads on the bottom have worn down, it is time
for replacement.
• The guide wheel is not excessively worn.
We recommend that you leave Kreepy Kadet in your pool, except during chemical shock treatments.
During swimming it is easy to unplug Kreepy Kadet and pull it to one side.
When storing Kreepy Kadet, do not coil the hose. Lay the hose out flat in an area protected from
direct sunlight. If hose sections are disconnected, try not to disturb the hose weight location.
To ensure optimum performance from your Kreepy Kadet, we recommend the use of blue sectional
hose by Pentair Pool Products.
VII. Customer Service
Your satisfaction is important to us, so we’re happy to help you get the best performance possible from
your new Kreepy Kadet. This manual covers the standard performance adjustments, which may apply
to your pool. If you still need help, call our Customer Helpline at 1-800.443-5711. Please have your
Kreepy Kadet serial number ready when you call.
Disclaimer of Liability –
About Your Pool and Kreepy Kadet.
Th e re are a multitude of fa c t o rs that contri bute to the life of your pool. The Kre epy Kadet product is a ve ry
p a s s ive product that will have no impact on pool life.
Please be awa re that , over time, d e t e ri o rat i o n , d i s c o l o rat i o n , and brittleness of pool plaster can be caused
s ep a rat e ly by, or in combination with,age,an imbalance in pool water ch e m i s t ry, i m p roper installat i o n , a n d
other fa c t o rs. An automatic pool cleaner such as Kre epy Kadet, will not re m ove or cause wear on “ go o d ” p o o l
p l a s t e r. In fa c t ,the opposite is true—pool plaster will eve n t u a l ly cause wear on the cl e a n e r.
The same situation holds true for vinyl-lined inground swimming pools, because vinyl liners are also affe c t e d
by the env i ronment and fa c t o rs such as pool water ch e m i s t ry, sunlight and the pool’s surroundings. Th e re fo re
over time,v i nyl can become brittle and weak. In add i t i o n , v i nyl-lined pools are affected by the wo rk m a n s h i p ,
composition and installation of the liner; and wo rkmanship and quality of construction of the supporting wa l l s
and pool base. These are all fa c t o rs wh i ch can contri bute to liner fa i l u re. The existence of any of these type of
conditions in your pool is not caused by the use or operation of Kre epy Kadet. The manu fa c t u rer discl a i m s
a ny liability for rep a i rs or replacement to any of these stru c t u res or components of the customer’s pool.
The pool owner must assume all responsibility for the condition and maintenance of the pool’s surfa c e,
water and deck .
K121680
Eyeball Diverter
K121683
Outer Ring
K12054
Hose Weight
K12932
Threaded
Compression
Adapter
K12662
Automatic
Regulator
Valve
K12961
Valve Cap
K12653
Swivel Head
Assembly
K12653C
Swivel Cone and Bearing
K12087
Bearing Washer
K12652
Footpad
K12654DB
Drive Tube
top/bottom (1)
K12655W
Bumper Strap
with Weight
“Insist on Genuine Kreepy Kadet Parts To Protect Your Warranty”
K121404
Step Deflector
K12658
Guide Wheel
K12656A
Float Assembly
K12649
Baffle Plate
K121620
Wire Diverter
K12094
Manual By-pass for Automatic
Regulator Valve
K12078
45° Hose Connector
(Without Flapper)
K12661
Skirt
K12664
Main Body
K12667
Pleated Seal
K12330
Ladder Guard
R211084K
Leaf Trap with Handle (clear)
K3500
Snap-Lock Wall Fitting
K50656
COMPLETE VACUUM
HOSE ASSEMBLY – BLUE
(32 ft. total length)
• 11 Sections M a l e / Fe m a l e
Hose (32'')
• 1 Section Female/Female
Hose (32'')
Notes
Loading...