Pentair Everpure WS-30 Installation Manual

Wine Storage Installation Guide

WINE STORAGE

Contents

3 Wine Storage

4 Model 424G / 424FSG Site Preparation

7 Model 424G / 424FSG Installation

11 Model 427G / 427RG Site Preparation

14 Model 427G / 427RG Installation

18 Model WS-30 Site Preparation

25 Model WS-30 Installation

Features and specications are subject to change at any time without notice. Visit subzero.com/specs for the most up-to-date information.

Important Note

To ensure this product is installed and operated as safely and efciently as possible, take note of the following types of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

WINE STORAGE

Product Information

Important product information including the model and serial number are listed on the product rating plate. The rating plate is located on the underside of the control panel, on the left. Refer to the illustrations below.

If service is necessary, contact Sub-Zero factory certied service with the model and serial number. For the name of the nearest Sub-Zero factory certied service or for questions regarding the installation, visit the contact & support section of our website, subzero.com or call Sub-Zero customer care at 800-222-7820.

RATING PLATE

Tools and Materials

• Screwdrivers—standard, Phillips and Torx.

• Power drill.

• Drill bits (masonry bits required for concrete installation).

• Standard socket and wrench set.

• 2' and 4' levels.

• Material to protect home, ooring and cabinetry during

installation.

Full-size models.

Undercounter models.

subzero.com | 3

MODEL 424G / 424FSG SITE PREPARATION

SIDE

Opening Dimensions

MODEL 424G

341/2"

(876)

OPENING

HEIGHT

VIEW FRONT VIEW

OPENING WIDTH

24" (610)

OPENING

DEPTH

TOP VIEW

W

DUAL INSTALLATION

When installing two units side by side in a dual installation, the opening width is determined by adding the single opening widths together.

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

OPENING WIDTH W

424G 24"

(610)

4 | Sub-Zero Customer Care 800.222.7820

MODEL 424G / 424FSG SITE PREPARATION

Electrical

Installation must comply with all applicable electrical codes.

The electrical supply should be located within the shaded area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

IMPORTANT NOTE: The electrical outlet must be placed so

the grounding prong is to the right of the thinner blades. The outlet must be ush with the back wall.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz Service 15 amp Receptacle 3-prong grounding-type

WARNING

Do not use an extension cord, two-prong adapter or remove the power cord ground prong.

Preparation

To operate properly, the door must open a minimum of 90°. Use a minimum 3" a 90° door opening.

Uncrate the unit and inspect for damage. Remove and recycle packing materials. Do not discard the kickplate, antitip bracket, hardware and the leveling legs which hold the wood base to the bottom of the unit.

(76) ller in corner installations to assure

LEFT SIDE

OF OPENING

2"

151/2"

(51)

Electrical supply location.

(394)

FLOOR

3" (76)

subzero.com | 5

MODEL 424G / 424FSG SITE PREPARATION

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip bracket must be installed.

MODEL 424G

The anti-tip bracket should be attached to the wall behind

1

the unit with the bracket ange located

/4" (6) above the top of the unit. Refer to the illustration below. Failure to properly position the anti-tip bracket will prevent proper engagement.

For installations that cannot accommodate the anti-tip bracket, a countertop bracket is provided to secure the unit to the countertop. Refer to the illustration below.

COUNTERTOP

BRACKET

1

/4" (6)

ANTI-TIP

BRACKET

MODEL 424FSG

The back of the anti-tip bracket must be installed 245/8"

(625)

from the front and centered behind the unit. Refer to the illustration below. Refer to page 13 for wood and concrete oor applications.

ANTI-TIP BRACKET

Anti-tip bracket (424FSG).

Anti-tip bracket (424G).

6 | Sub-Zero Customer Care 800.222.7820

Countertop bracket.

MODEL 424G / 424FSG INSTALLATION

Custom Panel

MODEL 424G

For overlay applications, a custom door panel must be installed. Panel size is critical for a proper t. To verify panel requirements and dimensions, refer to the Sub-Zero design guide at subzero.com/specs.

Finish all sides of the custom panel. They may be visible when the door is open or through the glass door.

The custom overlay door panel is attached using screws provided, through the door frame. Screw locations are marked on the back of the custom panel using tenon centers inserted into holes of the door frame.

With the unit secured and door closed, hold the custom panel in desired position on the door. Lightly tap the front of the panel to locate mounting positions. Remove tenon centers. Refer to the illustration below.

The door frame has mounting holes to accommodate Sub-Zero accessory handles. If handle mounting holes are not utilized, the handle should be attached to the custom panel prior to mounting. Screw heads may need to be countersunk into the panel for proper alignment.

To mount the custom panel, open the door and use predrilled holes to position the panel. Drive screws into the panel through black tape on the door frame. Screw holes are hidden behind the door gasket. Use as many screws as necessary to secure the custom panel. Refer to the illustration below.

Adjustments can be made to the custom panel with a few mounting screws in place, but not fully tightened. Once the proper position is achieved, install and secure all screws.

Cover holes on the inside of the door frame with the cover patches or plugs provided.

CAUTION

A solid panel cannot be installed over the glass door. A solid door is available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

Tenon center.

DOOR

FRAMEPANEL

TENON CENTER

GASKET

Door frame cross section.

13

/32" (11)

DIAMETER

GLASS

1

/4" (6)

DIAMETER

subzero.com | 7

MODEL 424G / 424FSG INSTALLATION

Placement

CAUTION

Before moving the unit into position, secure the door closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening.

If the unit has been on its back or side, it must stand upright for a minimum of 24 hours before connecting power.

If the unit will be connected to a home security system, run lead wires through the compressor compartment prior to positioning the unit. Refer to page 9. Once the unit is in position, wiring connection can be completed from the front.

Alignment

LEVELING

Level the unit before sliding it into position. Turn each of the four leveling legs clockwise to raise the unit and counterclockwise to lower. Refer to the illustration below.

DOOR ADJUSTMENT

The top and bottom cabinet hinges are held in place with three permanent adjustment screws. For adjustments, loosen the screws, adjust the door and tighten screws. Refer to the illustration below. For model 424FSG, only the bottom door hinge can be adjusted.

SCREW

HINGEADJUSTMENT

LEVELING LEGS

Leveling.

Door adjustment.

8 | Sub-Zero Customer Care 800.222.7820

MODEL 424G / 424FSG INSTALLATION

Completion

Plug the power cord into the grounded outlet, then slide the unit into position. Verify the anti-tip bracket is properly engaged.

1

It may be necessary to install the unit

/4" (6) beyond the front surface of adjacent cabinetry, to prevent interference when the door is opened to 145°. Refer to the full-scale template on page 10.

HOME SECURITY CONNECTION

If the unit will be connected to a home security system, make connections to the leads shown in the illustration below. Refer to the following color codes:

• Normally open contacts—white with red stripe wire.

• Normally closed contacts—white with blue stripe wire.

• Common—gray with white stripe wire.

Use the spade terminals or wire nuts provided to make proper wiring connections.

CAUTION

The alarm circuit in the unit is intended as a lowvoltage, low-current device only. It should not be used to switch line power. Any unused terminals should be completely insulated and all wires should be secured away from conductive or moving components.

ANCHORING

To anchor, use the countertop bracket provided to secure the unit to the underside of the countertop. Refer to the illustration below. If the countertop bracket can not be utilized, install shims along the top and sides of the unit.

KICKPLATE INSTALLATION

Install the kickplate using the two screws provided. Refer to the illustration below. The kickplate must be removable for service. The oor cannot interfere with removal. Do not cover the louvered section of the kickplate.

COUNTERTOP

BRACKET

KICKPLATE

Anchoring.

Kickplate installation.

HOME SECURITY

LEADS

Home security connection.

subzero.com | 9

MODEL 424G / 424FSG INSTALLATION

Door Clearance

FULL-SCALE TEMPLATE

To allow for a 145° door opening, the unit should extend

1

a minimum of

/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed ush, however, there is potential for interference with the panel if the door is opened past 90°.

UNDERCOUNTER

UNIT

DOOR CLOSED

1

/2"

(13)

ADJACENT

CABINETRY

3

/4" (19) DOOR PANEL

1" (25)0"

SCALE

145° door opening (top view).

10 | Sub-Zero Customer Care 800.222.7820

1

/4"

(6)

1

/8" (3)

HINGE AT 145°

OPENING

(DOOR OPENS PAST 145°)

MODEL 427G / 427RG SITE PREPARATION

SIDE

Opening Dimensions

MODELS 427G AND 427RG

H

OPENING

HEIGHT

25" (635)

OPENING

DEPTH

TOP VIEW

W

OPENING WIDTH

DUAL INSTALLATION

When installing two units side by side in a dual installation, the opening width is determined by adding the single opening widths together. A dual installation kit is required, but does not affect the opening width.

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

VIEW

FRONT VIEW

OPENING W H

427G 27"

(686) 80" (2032)

427RG 27" (686) 80" (2032)

The depth of models 427G and 427RG is 24" (610). Allow for panel thickness when planning the nished opening depth.

subzero.com | 11

MODEL 427G / 427RG SITE PREPARATION

Electrical

Installation must comply with all applicable electrical codes.

The electrical supply must be located within the shaded area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

The electrical outlet must be positioned with the grounding prong to the right of the thinner blades.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz Service 15 amp Receptacle 3-prong grounding-type

CAUTION

The outlet must be checked by a qualied electrician to be sure that it is wired with the correct polarity. Verify that the outlet is properly grounded.

WARNING

Do not use an extension cord, two-prong adapter or remove the power cord ground prong.

Preparation

Uncrate the unit and inspect for damage. Remove the wood base and discard shipping bolts and brackets. Remove and recycle packing materials. Do not discard the kickplate, antitip bracket and hardware.

IMPORTANT NOTE: For model 427RG, the upper drawer has

a control cable that must be disconnected before removing the drawer. Refer to the illustration below.

Control cable (model 427RG).

LEFT SIDE

OF OPENING

21/2"

(64)

13" (330)

41/2"

(

)

114

1

/4"

(6)

Electrical supply location.

12 | Sub-Zero Customer Care 800.222.7820

FLOOR

MODEL 427G / 427RG SITE PREPARATION

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip bracket must be installed.

The back of the anti-tip bracket must be installed 24" (610) from the front of the unit (without panels).

Use all anti-tip bracket hardware as instructed for wood or concrete oors.

IMPORTANT NOTE: For wood or concrete oor applications,

if the #12 screws do not hit a wall stud or wall plate, use the #8 screws and #12 washers with the wall anchors.

IMPORTANT NOTE: In some installations the subooring or

nished oor may necessitate angling the screws used to fasten the anti-tip bracket to the back wall.

ANTI-TIP HARDWARE

1 Anti-tip bracket

1

12 #12 x 2

4

12 #12 at washers

4 #8–18 x 1 4 Nylon Zip-it

/2" pan head screws

3

/8"–16 x 33/4" wedge anchors

1

/4" truss head screws

®

wall anchors

WOOD FLOOR

After properly locating the anti-tip bracket in the opening,

3

drill pilot holes

/16" (5) diameter maximum in the wall studs or wall plate. Use the #12 screws and washers to secure the brackets. Verify the screws penetrate through the ooring material and into wall studs or wall plate a minimum of

3

/4" (19). Refer to the illustration and chart below.

CONCRETE FLOOR

After properly locating the anti-tip bracket in the opening,

3

drill pilot holes or wall plate. Drill a minimum of 1 washers to secure the brackets to the wall, and use the

/16" (5) diameter maximum in the wall studs

3

/8" (10) diameter holes into the concrete

1

/2" (38) deep. Use the #12 screws and

3

/8" wedge anchors to secure the brackets to the oor. Verify the screws penetrate wall studs or wall plate a minimum of

3

/4" (19). Refer to the illustration and chart below.

ANTI-TIP BRACKET

MODEL A

427G and 427RG 131/2" (343)

WALL PLATE

SUBFLOORING

Wood oor.

A

FINISHED FLOORING

WOOD FLOOR

A

WALL PLATE

SUBFLOORING

CONCRETE

FLOOR

A

FINISHED FLOORING

11/2"(38)

min

Concrete oor.

subzero.com | 13

MODEL 427G / 427RG INSTALLATION

Anti-Tip Bracket

CONCRETE WEDGE ANCHOR INSTALLATION

1 Drill a

2 Assemble the washer and nut ush with the end of

3 Expand the anchor by tightening the nut 3–5 turns past

Verify there are no electrical wires or plumbing in the area which the screws could penetrate.

Always wear safety glasses and use other necessary protective devices or apparel when installing or working with anchors.

Anchors are not recommended for use in lightweight masonry material such as block or brick, or for use in new concrete which has not had sufcient time to cure. The use of core drills is not recommended to drill holes for the anchors.

3

/8" (10) diameter hole any depth exceeding the minimum embedment. Clean the hole or drill additional depth to accommodate drill nes.

anchor to protect threads. Drive the anchor through the material to be fastened until the washer is ush with the surface material.

hand-tight position or to 25 ft-lb of torque.

WARNING

CAUTION

Custom Panels

For models 427G and 427RG, custom panels and handle hardware must be installed. Stainless steel panels are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

PANEL REQUIREMENTS

PANEL WEIGHT MAX

Door 20 lb (9 kg) Drawer (427RG) 12 lb (5 kg)

PANEL THICKNESS MIN

All Panels

Reveals between panels can vary, 1/8" (3) reveals are typical.

CAUTION

When using a panel thicker than 3/4" (19) with reveal less

1

than

/4" (6), panel may cause damage to the unit when

door is opened to 105°. Use the built-in 90° door stop.

CAUTION

As reveals between cabinetry and the unit decrease, severe nger pinching can occur while door is closing.

Finish all sides of the custom panel. They may be visible when the door is open or through the glass door.

5

/8" (16)

14 | Sub-Zero Customer Care 800.222.7820

D-style handles are recommended. Stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. The door handle must be located near the edge of the panel opposite the hinge and should be centered top to bottom.

CAUTION

A solid panel cannot be installed over the glass door. A solid door is available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

MODEL 427G / 427RG INSTALLATION

Panel Installation

The custom overlay door panel is attached using screws provided through the door frame. Screw locations are marked on the back of the custom panel using tenon centers inserted into holes of the door frame.

With the unit secured and door closed, hold the custom panel in desired position on the door. Lightly tap the front of the panel to locate mounting positions. Remove tenon centers. Refer to the illustration below.

The door frame has mounting holes to accommodate Sub-Zero accessory handles. If handle mounting holes are not utilized, the handle should be attached to the custom panel prior to mounting. Screw heads may need to be countersunk into the panel for proper alignment.

To mount the custom panel, open the door and use predrilled holes to position the panel. Drive screws into the panel through black tape on the door frame. Screw holes are hidden behind the door gasket. Use as many screws as necessary to secure the custom panel. Refer to the illustration below.

Adjustments can be made to the custom panel with a few mounting screws in place, but not fully tightened. Once the proper position is achieved, install and secure all screws.

Cover holes on the inside of the door frame with the cover patches or plugs provided.

DRAWER PANELS (MODEL 427RG)

Remove the mounting hardware attached to the front of the unit and set aside. Place the panel face down on a protected work surface.

Position the top edge of the template ush with the top edge of the panel. Depending on the height and thickness of the lower drawer panel, the bracket may need to be inverted for proper placement. Mark and drill pilot holes, then secure

1

brackets to panel using the #8 x

/2" screws provided. Refer

to the illustration below.

To help with placement of drawer panels, examine the lower L-bracket and panel to determine the slotted holes on the bracket that will be used. Then position screws into the lower portion of the drawer that correspond with these slots. Leave the screws out slightly so the slotted holes will slide under the heads.

Install the panel by engaging the tabbed bracket to the top of the drawer, then rotate the panel until the lower bracket is properly positioned below the drawer. The panel can be

1

adjusted

/4" (6) up and down and side to side.

Once the panel is properly aligned, attach the remaining

1

/2" screws to the mounting bracket.

#10 x

Reconnect the control cable before reinstalling the top drawer. Refer to page 12.

Tenon center.

DOOR

FRAMEPANEL

TENON CENTER

GASKET

Door frame cross section.

13

/32" (11)

DIAMETER

GLASS

1

/4" (6)

DIAMETER

TEMPLATE FLUSH WITH

TOP OF PANEL

SIDE EDGE GAP WILL VARY

BACK OF PANEL

Template position.

TABBED BRACKET

L BRACKET

Drawer panel installation.

subzero.com | 15

MODEL 427G / 427RG INSTALLATION

Placement

CAUTION

Before moving the unit into position, secure the door/ drawers closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening. Front and rear leveling legs can be adjusted from the front once the unit is positioned.

If the unit has been on its back or side, it must stand upright for a minimum of 24 hours before connecting power.

If the unit will be connected to a home security system, run lead wires through the compressor compartment prior to positioning the unit. Refer to page 17. Once the unit is in position, wiring connection can be completed from the front.

Plug the power cord into the grounded outlet, then slide the unit into position. Verify the anti-tip bracket is properly engaged.

Alignment

LEVELING

Once the unit is in position, height adjustment can be made from the front. Using a standard screwdriver, turn front leveling legs clockwise to raise the unit or counterclockwise to lower. Using a Phillips drive, turn rear adjustment screws clockwise to raise the unit or counterclockwise to lower. Use the lowest torque setting when using a power drill (18 revolutions equals rear leveling legs by hand. Refer to the illustrations below.

Level the unit to the oor, not surrounding cabinetry. This could affect the operation of the unit, such as door closing. When the unit is properly leveled, door/drawer adjustments are less likely to be necessary.

Secure the unit in place using the side mounting clips and

1

/2" screws provided.

#8 x

WARNING

To reduce the possibility of the unit tipping forward, the front leveling legs must be in contact with the oor.

1

/16" of height adjustment). Do not turn the

16 | Sub-Zero Customer Care 800.222.7820

Front adjustment.

Rear adjustment.

MODEL 427G / 427RG INSTALLATION

Completion

TRIM INSTALLATION

Install decorative trim strips to the top and sides of the unit. Attach the top trim using the double-sided velcro, then snap side trim over brackets on the sides of the unit. Refer to the illustration below.

HOME SECURITY CONNECTION

If the unit will be connected to a home security system, make connections to the leads shown in the illustration below. Refer to the following color codes:

• Normally open contacts—white with red stripe wire.

• Normally closed contacts—white with blue stripe wire.

• Common—gray with white stripe wire.

Use the spade terminals or wire nuts provided to make proper wiring connections.

CAUTION

The alarm circuit in the unit is intended as a lowvoltage, low-current device only. It should not be used to switch line power. Any unused terminals should be completely insulated and all wires should be secured away from conductive or moving components.

KICKPLATE INSTALLATION

Install the kickplate using the screws provided. The mounting bracket may be adjusted slightly for a ush t. The kickplate must be removable for service. The oor cannot interfere with removal. Refer to the illustration below.

A decorative kickplate can be added to the factory-installed kickplate but cannot block the kickplate louvers.

Turn power on by touching POWER on the control panel.

90° DOOR STOP

The door opens to 105°. A 90° door stop is built into the hinge system for installations where the door opening must be limited.

To engage the door stop, use a standard screwdriver and rotate the center cam of the hinge. The adjustment must be made to both upper and lower hinges. Refer to the illustration below.

HOME SECURITY

LEADS

Home security connection.

SIDE TRIM

Trim installation.

TOP TRIM

Kickplate installation.

MOUNTING

BRACKET

90° door stop.

subzero.com | 17

MODEL WS-30 SITE PREPARATION

NOTE: Shaded line represents profile of unit.

SIDE

Opening Dimensions

STANDARD INSTALLATION

24" (610)

OPENING

DEPTH

TOP VIEW

W

OPENING WIDTH

FRONT VIEW

VIEW

833/4"

(2127)

OPENING

HEIGHT

OPENING WIDTH W

1

WS-30 29

/2" (749)

If two units are installed side by side, refer to page 20.

18 | Sub-Zero Customer Care 800.222.7820

MODEL WS-30 SITE PREPARATION

*3

NOTE: Shaded line represents profile of unit with

SIDE

Opening Dimensions

FLUSH INSET INSTALLATION

263/16"

(665)

FLUSH

INSET

23/16"

DEPTH

(56)

TOP VIEW

FINISHED

CLEATS*

1

/4"

(6)

84"

(2134)

FLUSH

INSET

HEIGHT

VIEW

" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.

3/4" (19) panel.

11/4"

(32)

FLUSH INSET WIDTH

FRONT VIEW

W

4" (102)

11/4"

(32)

3"

(76)*

TYPICAL

23/16"

(56)

FLUSH INSET WIDTH W

WS-30 32"

(813)

Dimensions assume a 3/4" (19) panel thickness. If two units are installed side by side, refer to page 21.

subzero.com | 19

MODEL WS-30 SITE PREPARATION

NOTE: Shaded line represents profile of unit.

SIDE

Opening Dimensions

DUAL STANDARD INSTALLATION

24" (610)

OPENING

DEPTH

TOP VIEW

VIEW

833/4"

(2127)

OPENING

HEIGHT

OPENING WIDTH

OPENING WIDTH W

3

WS-30 and 30" Built-In Model 59

/4" (1518)

WS-30 and 36" Built-In Model 653/4" (1670)

W

FRONT VIEW

A dual installation kit will be required for this installation.

20 | Sub-Zero Customer Care 800.222.7820

MODEL WS-30 SITE PREPARATION

*3

NOTE: Shaded line represents profile of unit with

SIDE

Opening Dimensions

DUAL FLUSH INSET INSTALLATION

263/16"

(665)

FLUSH

INSET

23/16"

DEPTH

(56)

TOP VIEW

FINISHED

CLEATS*

1

/4"

(6)

84"

(2134)

FLUSH

INSET

HEIGHT

VIEW

" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.

3/4" (19) panel.

11/4"

(32)

FLUSH INSET WIDTH

FRONT VIEW

W

11/4"

(32)

4" (102)

3"

(76)*

TYPICAL

23/16"

(56)

FLUSH INSET WIDTH W

WS-30 and 30" Built-In Model 62 WS-30 and 36" Built-In Model 681/4" (1734)

1

/4" (1581)

Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.

subzero.com | 21

MODEL WS-30 SITE PREPARATION

Dual Installation

If two units are installed side by side, a dual installation kit may be required. Installations without a custom ller strip require a dual installation kit. If a dual installation kit is not specied, a 2" Dual installations without a ller strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below.

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

(51) ller strip is recommended between units.

Electrical

Installation must comply with all applicable electrical codes.

The electrical supply should be located within the shaded area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz Service 15 amp Receptacle 3-prong grounding-type

CAUTION

The outlet must be checked by a qualied electrician to be sure that it is wired with the correct polarity. Verify that the outlet is properly grounded.

WARNING

Do not use an extension cord, two-prong adapter or remove the power cord ground prong.

WITHOUT FILLER STRIP

Opposite hinges.

FILLER STRIP

Same side hinges.

7"

E

(178)

6"

(152)

751/2" (1918)

FROM FLOOR

RIGHT SIDE

OF OPENING

Electrical supply location.

22 | Sub-Zero Customer Care 800.222.7820

MODEL WS-30 SITE PREPARATION

Preparation

Uncrate the unit and inspect for damage. Remove the wood base and discard shipping bolts and brackets. Remove and recycle packing materials. Do not discard the kickplate, antitip brackets and hardware.

Completely retract the front leveling legs to allow the unit to be moved into position. The front and rear leveling legs can be adjusted from the front once the unit is in position.

Remove the drain pan to avoid damage, and allow for proper appliance dolly placement.

The grille assembly should be removed prior to moving the unit. To remove, pull out on the bottom edge of the grille and rotate upward. Loosen the two back grille mounting screws and remove the two front grille mounting screws. With the grille held rmly, pull forward to remove. Refer to the illustrations below.

Grille removal.

BACK GRILLE

SCREW

Grille mounting screws.

ADJUSTMENT

FRONT

GRILLE SCREW

SCREWS

GRILLE

subzero.com | 23

MODEL WS-30 SITE PREPARATION

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip brackets must be installed.

The two anti-tip brackets must be installed exactly 24"

(610)

from the front of the opening to the back of the brackets and a minimum of 4" opening. This depth will increase to 26 inset installation, based on

(102) from the sides of the

3

/4" (19) thick panels. Failure to

/16" (665) for a ush

properly position the anti-tip brackets will prevent proper engagement.

Use all anti-tip bracket hardware as instructed for wood or concrete oors.

IMPORTANT NOTE: For wood or concrete oor applications,

if the #12 screws do not hit a wall stud or wall plate, use the #8 screws and #12 washers with the wall anchors.

IMPORTANT NOTE: In some installations the subooring or

nished oor may necessitate angling the screws used to fasten the anti-tip brackets to the back wall.

ANTI-TIP HARDWARE

2 Anti-tip brackets

1

12 #12 x 2

4

12 #12 at washers

4 #8–18 x 1 4 Nylon Zip-it

/2" pan head screws

3

/8"–16 x 33/4" wedge anchors

1

/4" truss head screws

®

wall anchors

WOOD FLOOR

After properly locating the anti-tip brackets in the opening,

3

drill pilot holes

/16" (5) diameter maximum in the wall studs or wall plate. Use the #12 screws and washers to secure the brackets. Verify the screws penetrate through the ooring

3

material and into wall studs or wall plate a minimum of

(19)

. Refer to the illustration below.

/4"

CONCRETE FLOOR

After properly locating the anti-tip brackets in the opening,

3

drill pilot holes or wall plate. Drill a minimum of 1 washers to secure the brackets to the wall, and use the

/16" (5) diameter maximum in the wall studs

3

/8" (10) diameter holes into the concrete

1

/2" (38) deep. Use the #12 screws and

3

/8"

wedge anchors to secure the brackets to the oor. Verify the

3

24"

(610)

4" (102)

MIN

/4"

screws penetrate wall studs or wall plate a minimum of

(19)

. Refer to the illustration below.

24"

(610)

4" (102)

MIN

24 | Sub-Zero Customer Care 800.222.7820

WALL PLATE

SUBFLOORING

Wood oor.

FINISHED

FLOORING

WOOD FLOOR

WALL PLATE

SUBFLOORING

CONCRETE

FLOOR

Concrete oor.

FINISHED

FINISHED FLOORING

FLOORING

11/2"(38)

min

MIN

MODEL WS-30 INSTALLATION

Anti-Tip Bracket

CONCRETE WEDGE ANCHOR INSTALLATION

1 Drill a

2 Assemble the washer and nut ush with the end of

3 Expand the anchor by tightening the nut 3–5 turns past

Verify there are no electrical wires or plumbing in the area which the screws could penetrate.

Always wear safety glasses and use other necessary protective devices or apparel when installing or working with anchors.

Anchors are not recommended for use in lightweight masonry material such as block or brick, or for use in new concrete which has not had sufcient time to cure. The use of core drills is not recommended to drill holes for the anchors.

3

/8" (10) diameter hole any depth exceeding the minimum embedment. Clean the hole or drill additional depth to accommodate drill nes.

anchor to protect threads. Drive the anchor through the material to be fastened until the washer is ush with the surface material.

hand-tight position or to 25 ft-lb of torque.

WARNING

CAUTION

Custom Panels

For overlay and ush inset applications, custom door and grille panels must be installed. Panel size is critical for a proper t. To verify panel requirements and dimensions, refer to the Sub-Zero design guide at subzero.com/specs.

IMPORTANT NOTE: Flush inset applications require a

minimum

Finish all sides of the custom panel. They may be visible when the door is open or through the glass door.

A solid panel cannot be installed over the glass door.

1

/2" (13) reveal on all sides.

CAUTION

subzero.com | 25

MODEL WS-30 INSTALLATION

Panel Installation

DOOR PANEL

To install the custom door panel, remove the handle side trim molding. Insert a screwdriver tip into the top corner slot on the handle side and pop out the trim. Remove the screws and frame. Refer to the illustration below.

1

The door has a into. If the panel is thicker than a around the panel or mount the panel on a sheet of

/4" (6) frame for the custom panel to slide

1

/4" (6), rout an edge

1

/4" (6)

thick material, then insert into the frame.

Door side trim.

(3) space is required between the backer panel and

A .10" the custom panel to allow the panel to slide into the door frame. Refer to the illustrations below for critical dimensions.

Install handle hardware before inserting the panel. Large D-style handles are recommend rather than knobs. Screw heads must be countersunk into the panel.

Slide the panel into the frame.

To reinstall the door trim molding, insert the top of the trim into grooves at the top of the door and work downward, snapping the trim into clips on the door frame.

SPACER PANEL

CUSTOM PANEL

BACKER PANEL

TRIM

5

/16" (8) min

1

/8" (3) (OVERLAY)

Panel assembly cross section (overlay).

CUSTOM

PANEL

3

/4"

(19)

.10" (3)

typical

Panel assembly rear view.

1

/4" (6)

SPACER

PANEL

BACKER

PANEL

26 | Sub-Zero Customer Care 800.222.7820

MODEL WS-30 INSTALLATION

84"

(2134)

24"

(610)

OPTIONAL

TOE KICK

CUT-OUT

4" (102)

17/8"(48)

1" (25)

ROUT TO

1

/8"

(3)

FRONT

OF SIDE

PANEL

25/8"

(67)

MAIN

FRAME

SIDE PANEL

ROUTING

1" (25)

17/8" (48)

1

/8" (3)

1

/2" (13)

Panel Installation

GRILLE PANEL

Remove the bottom grille frame by extracting the lower two corner screws from each side of the grille assembly. Refer to the illustration below.

With the bottom section removed, slide the custom grille

1

panel into the frame. If the panel is thinner than

/4" (6), a ller material will need to be installed to achieve a proper t. Once the panel is installed, reattach the bottom grille frame by sliding the corner brackets back into position, then reinstall the four corner screws.

BOTTOM

GRILLE FRAME

SIDE PANEL

When installing a custom side panel, an accessory kit is required and is available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. Stainless steel and white enamel side panels are also available from an authorized Sub-Zero dealer.

IMPORTANT NOTE: The use of side panels may change the

width of the opening.

A custom side panel must be a minimum of 24"

1

/2" (13) thick. Routing will be necessary for the side

and

(610) deep

panel to t ush against the side of the unit. Refer to the illustrations below.

IMPORTANT NOTE: The height of the side panel will vary

with the height of the grille. Verify the nished height before modifying panels.

Grille frame assembly.

Routing detail.

Side panel dimensions.

subzero.com | 27

MODEL WS-30 INSTALLATION

Placement

CAUTION

Before moving the unit into position, secure the door closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening.

If the unit has been on its back or side, it must stand upright for a minimum of 24 hours before connecting power.

If the unit will be connected to a home security system, run lead wires through the compressor compartment prior to positioning the unit. Refer to page 30. Once the unit is in position, wiring connection can be completed from the front.

Plug the power cord into the grounded outlet, then roll the unit into position. Verify the anti-tip brackets are properly engaged.

IMPORTANT NOTE: If used, side panels will need to be

installed before the unit is placed in its nal position. Refer to page 27.

Alignment

LEVELING

Once the unit is in position, turn the front leveling legs clockwise to adjust the height. The rear height adjustment can be made from the front of the roller base. Using a

3

socket, turn the

/8" hex bolt clockwise to raise the unit or counterclockwise to lower. Use the lowest torque setting when using a power drill. Do not turn the rear leveling legs by hand. Refer to the illustration below.

When the unit is properly leveled, door adjustments are less likely to be necessary.

IMPORTANT NOTE: Level the unit to the oor, not sur-

rounding cabinetry. This could affect the operation of the unit, such as door closing.

WARNING

To reduce the possibility of the unit tipping forward, the front leveling legs must be in contact with the oor.

3

/8"

28 | Sub-Zero Customer Care 800.222.7820

Leveling.

FRONT

LEVELING LEG

REAR

ADJUSTMENT