Pentair Everpure CB20-302E Installation Manual

GENERAL PRECAUTIONS

Maximum Pressure: 20-100 psi non-shock (1.4-6.9 bar)
Temperature: 35-100°F (2-38°C)

Install On Cold Water Lines Only

Installation By a Certified Installer Is Recommended

Housing Inlet & Outlet 3/4"

Rated service flow: 5 gpm (19 Lpm)
Capacity: 20,000 gal (75,700 L)

For cold water use only!

WARNING: This filter must be protected from freezing. Failure to do
so may result in crackingof the filter and water leakage.

Do not install where unit is exposed to direct sunlight.

Allow a minimum of 4" clearance under the filter to facilitate cartridge
change. Make certain that the installation complies with all state and
local laws and regulations.

WARNING: Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.

NOTE: The carbon taste/odor cartridge may contain small amounts
of carbon fines (very fine black powder) and a new cartridge, after
installation, should be flushed with sufficient water to remove the fines
before using the water.

CB20-302E WATER FILTRATION SYSTEM

SYSTEM INSTALLATIONS

NOTE: Always use a good grade of pipe sealant or teflon®tape on

connections.

1. Reduce product weight by removing bowls from header assembly

before mounting unit.

2. Determine installation location using head assembly.

3. Assemble flush valve kit per illustration in its instruction sheet.

4. Install system brackets. Mount system. Mount system to wall

studs 16" on center (spacing of mounting plate holes) on other
surface capable of supporting 60 pounds when system is filled
with water.

5. Install system brackets. Mount system.

6. Turn off water and power supply to all beverage equipment and

icemaker.

7. Connect cartridge system to feed water supply, beverage

systems, and icemaker.

8. Sanitize filter bowls using dilute (0.5%) household bleach solution,

Diversol™ or equivalent.

9. Handle cartridges by plastic wrap to minimize contact.

10. Lubricate “O-rings” with silicone lubricant and secure to system

head. Hand tighten.

11. Cartridge flush procedure:

- Install CC1E cartridge leaving CC3E bowl empty.

- Flush cartridge at full flow for 5 minutes.

- Install CC3E cartridge and flush system for 10 minutes.

12. Close valve and inspect for leaks.

13. Turn power to beverage and ice maker back on.

14. Clean up and give final inspection.

15. Obtain Manager sign-off on work confirmation form.

REPLACEMENT CARTRIDGES

CC1E Carbon Filter (gray end caps)
CC3E Cyst Filter (white end caps)

Replace CC1E and CC3E cartridges every 12 months or 20,000
gallons (whichever comes first).

1. Turn power off to beverage equipment.

2. Turn water off to CB20-302E system.

3. Unscrew bowl assembly from header, remove exhausted cartridge
and discard. CAUTION: Bowl is heavy.

4. Unwrap new cartridge and place in bowl. Screw bowl into

appropriate head on system.

5. Turn on water and flush cartridges. (Refer to cartridge flush
procedure, step 11 under System Installations)

For assistance or to locate the nearest dealer for replacements parts
or service call:

Everpure Customer Service 1-800-323-7873
Everpure Technical Service 1-800-942-1153

Part Number EV9100-32

INSTALLATION AND OPERATING INSTRUCTIONS

CB20-302E WATER FILTRATION SYSTEM

Mounting Depth: 9"
Operating Weight: 60 lbs.

Flush Valve

3

/4" Female
Outlet
Connection to
Equipment

3

/4" Female
Inlet
Connection
from Supply

27 3/4"

20 3/4"

PERFORMANCE DATA

CB20-302E System Replacement Cartridge Kit EV910521

1- CC1E Replacement Cartridge (gray end caps)
1- CC3E Replacement Cartridge (white end caps)

FEATURES

• Finely polishes treated water to premium quality for drinking and
cooking.

• Reduces disinfectant chlorine taste & odor and chloramine taste &
odor.

• Reduces dirt, rust, and other particulates such as oxidized iron,
manganese, and sulfides.

• Reduces parasitic protozoan cysts such as Giardia, Entamoeba,

Cryptosporidium.

• Reduces common earthy, moldy, fishy tastes and odors.

OPERATING SPECIFICATIONS

Capacity: 20,000 gallons (75,700 L)
Pressure requirement: 20-100 psi (1.4-6.9 bar), non-shock
Temperature: 35-100°F (2-38°C)
Flow Rate: 5 gpm (19 Lpm)
Operating Weight: 60 lbs.

GENERAL INSTALLATION/OPERATION/
MAINTENANCE REQUIREMENTS

• Mount system to wall studs 16" on center (spacing of mounting
plate holes) or other surface capable of supporting 60 pounds
when system is filled with water.

• Connect water supply to "inlet of CB20-302E system"

• Connect outlet water to beverage equipment

• Press red pressure relief to purge air

• After installing the CC1E cartridge, flush cartridge at full flow for 5
minutes. Install CC3E and flush system for 10 minutes

• Replace cartridges when capacity is reached, or when flow
becomes too slow, but at least annually

SPECIAL NOTICES

• Installation instructions, parts and service availability, and standard
warranty are included with the product when shipped. Installation
by certified installer is recommended.

• This drinking water system must be maintained according to
manufacturer's instructions, including replacement of filter
cartridges.

• The contaminants or other substances removed or reduced by
this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Testing was performed under standard laboratory conditions;
actual performance may vary.

©2009 by Everpure, LLC SH147956 Rev A MY09

EVERPURE, LLC

1040 Muirfield Drive
Hanover Park, IL 60133

TEL [phone]

Customer Service
FAX [phone]

Visit us online at: www.everpure.com

In Europe:

EVERPURE EUROPE NV

Toekomstlaan 30
B-2200 Herentals
Belgium
Tel [phone]
FAX [phone]

In Japan:

EVERPURE JAPAN, INC.

Hashimoto MN Bldg. 7F
3-25 Hashimoto Sagamihara-S
Kanagawa 229-1103
Japan
Tel [phone]
FAX [phone]