Pentair SCREENLOGIC INTERFACE Installation Manual

SCREENLOGIC® INTERFACE Wireless Connection Kit Installation Guide

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTALLATION GUIDE

SCREENLOGIC® INTERFACE

WIRELESS CONNECTION KIT

FOR INTELLITOUCH® AND EASYTOUCH® CONTROL SYSTEMS

SCREENLOGIC® INTERFACE Wireless Connection Kit Installation Guide

Technical Support

Sanford, North Carolina (8 A.M. to 4:30 P.M.)

Phone: [phone]
Fax: [phone]
Moorpark, California (8 A.M. to 4:30 P.M.)
Phone: [phone] (Ext. 6502)
Fax: [phone]
Web sites: visit www.pentairpool.com and www.staritepool.com

Related manual: ScreenLogic

®

Interface User’s Guide (P/N 520493)

Contents

Overview ........................................................................................................... 1

Summary installation steps ............................................................................... 1

In this Installation Guide ................................................................................... 1

ScreenLogic Interface Wireless Connection Kit Contents ...............................2

Step 1: Mount the Outdoor Wireless Transceiver and Connect to the

IntelliTouch or EasyTouch Load Center ........................................................... 3

Step 2: Connect the Indoor Wireless Transceiver to the ScreenLogic

Interface Protocol Adapter ................................................................................ 8

FCC Regulatory Safety Notice - This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• Modifications not expressly approved by the party responsible for FCC

compliance could void the user’s authority to operate the equipment.

In this Installation Guide

Use the information in this manual for installing the ScreenLogic® Interface
Wireless Connection kit contents.

• For ScreenLogic Interface system operating instructions, refer to

the ScreenLogic Interface User’s Guide (P/N 520493)

SCREENLOGIC® INTERFACE Wireless Connection Kit Installation Guide

1

Overview

The ScreenLogic® Interface Wireless Connection kit consists of two
wireless 2.4 GHz 900 Mhz transceivers which provides a wireless
connection between the ScreenLogic Interface Protocol adapter and the
IntelliTouch

®

or EasyTouch®Control System Load Center located at the
equipment pad. This wireless connection eliminates the existing hard
wire connection from inside your home to the equipment pad.

ScreenLogic Interface Wireless Connection Kit Contents

The following items are included in the Wireless Connection kit.

• One ScreenLogic Interface indoor wireless transceiver with AC

power adapter and one foot connection cable with attached plugs.

• One ScreenLogic Interface outdoor wireless transceiver with 10

foot cable, provided in kit with enclosure and mounting hardware.

• ScreenLogic Interface Wireless Connection Installation Guide

(this manual)

Kit Contents

Transceiver
Enclosure

AC transformer

Indoor transceiver

Outdoor transceiver

ScreenLogic
Interface Protocol
Adapter (purchased
separately)

Transceiver
Enclosure

Mounting hardware

Protocol Adapter

LAN

LABEL P/N 520535

RESET

SERIAL CONNECTION

Black Green Yellow Red

P/N 520489

SCREENLOGIC® INTERFACE Wireless Connection Kit Installation Guide

1

Antenna
location

RX: This LED is
on when a signal
is being received
from the wireless
transceiver in the
outdoor clam
shell.
TX: This LED is
on when a signal
is being
transmitted to the
wireless
transceiver in the
outdoor clam
shell.

RS-485 Connector
(to Protocol Adapter)

Power LED

ScreenLogic Interface

Summary installation steps

The ScreenLogic® Interface connection diagram on page 2 shows the
transceiver locations and connections. To install the ScreenLogic Interface
Wireless Connection kit:

• Mount the transceiver antenna near the IntelliTouch® or

EasyTouch® Control System Load Center and connect the
transceiver to the COM port connector located in the IntelliTouch

®

or EasyTouch® Control System Load Center.

• Use the supplied 12 inch cable to connect the ScreenLogic

Interface indoor wireless transceiver to the ScreenLogic Interface
Protocol adapter. Plug the transceiver AC power adapter into an
AC wall-outlet and into the transceiver unit to power up the unit.