KREEPY KRAULY® WARRIOR
™
SUCTION SIDE POOL CLEANER
ENGLISH 1
ESPAÑOL 13
FRANÇAIS 29
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
INSTALLATION AND
USER’S GUIDE
i
CUSTOMER SERVICE / TECHNICAL SUPPORT
If you have questions about ordering Pentair Aquatic Systems™ replacement parts and pool products, please
contact:
Customer Service and Technical Support, USA
(8 A.M. to 5 P.M. — Eastern/Pacific Times)
Phone: (800) 831-7133
Fax: (800) 284-4151
Web site
Visit www.pentairpool.com or www.staritepool.com
TABLE OF CONTENTS
Important Warning and
Safety Instructions ..............................................
Pool Preparation ...................................................
Cleaner Components
Assembling the Cleaner ......................................
Hose Assembly
Installing the Cleaner ...........................................
Standard Installation
Vacuum Line Installation
Adjusting Flow with the Flow Gauge
Calculating Cleaner RPM Without the
Flow Gauge
Cleaner Adjustments and Operation ..................
Hose Length
Return Line Water Flow
Installing the Eyeball Diverter
Eyeball Diverter Positions
Sanford, North Carolina (8 A.M. to 5 P.M. ET)
Phone: (919) 566-8000
Fax: (919) 566-8920
Moorpark, California (8 A.M. to 5 P.M. PT)
Phone: (805) 553-5000 (Ext. 5591)
Fax: (805) 553-5515
Maintenance ........................................................
ii
1
1
2
2
3
3
4
5
5
6
6
7
7
7
Removing Debris from Turbine
Tire Removal
Tire Replacement
Troubleshooting ..................................................
Replacement Parts ............................................
8
8
9
9
10
11
P/N 371302 Rev. A 8/28/14
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
ii
Important Notice:
Attention Installer: This guide contains important information about the
installation, operation and safe use of this product. This information should
be given to the owner and/or operator of this equipment after installation
of the pool cleaner.
Attention User: This manual contains important information that will help
you in operating and maintaining this pool cleaner. Please retain it for future
reference. Consult Pentair with any questions regarding this equipment.
Before installing this product, read and follow all
warning notices and instructions which are included.
Failure to follow safety warnings and instructions can result in severe
injury, death, or property damage. Call (800) 831-7133 for additional free
copies of these instructions.
Consumer Information and Safety
This pool cleaner is designed and manufactured to provide many years
of safe and reliable service when installed, operated and maintained
according to the information in this manual. Throughout the manual, safety
warnings and cautions are identified by the “ ” symbol. Be sure to read
and comply with all of the warnings and cautions.
HAZARDOUS SUCTION.
Do not play with cleaner or hose or apply to body.
Can trap and tear hair or body parts. Hose can trip or
entangle swimmers which could result in drowning.
SUCTION ENTRAPMENT, INJURY, AND
DROWNING HAZARD. If your pool has a dedicated
suction port (“vac port”) for vacuuming or for an
automatic pool cleaner, it must be covered when
not in use. A spring loaded safety cover (a “vac port
fitting”) is included with your cleaner. Install it on the
suction port to prevent entrapment and injury. If the
cover provided does not fit, purchase one that does
from your local pool store and install it instead. The
cover should conform to IAPMO SPS4-99A.
General Installation Information
Pre-Installation Check List
Before installing your cleaner, review and understand all warnings and
safety information in this guide. Failure to follow these instructions or
improper installation of the cleaner can result in damage to the pool finish
or the vinyl liner, Pentair Water Pool and Spa, Inc. disclaims any liability
for repairs or replacement to any of these structures or components of
the customer’s pool.
Before installing the cleaner in a vinyl liner pool:
Check liner closely for signs of deterioration or damage from age,
chemicals, pool wall damage, etc. If any damage is found, have a qualified
pool professional make all the necessary repairs. Also, if there are stones,
roots, etc., under the liner, remove them before installing the cleaner.
Before installing the cleaner in a gunite pool or a pool that is partially
or completely tiled:
Repair loose tiles and tighten any loose light rings.
Before installing the cleaner, clean your filter system:
Make sure you have cleaned the filter, including backwashing, rinsing,
and emptying all baskets. A clean system is necessary for proper cleaner
operation and coverage.
Before installing the cleaner, understand cleaner coverage:
The cleaner is designed to rid your pool of debris in approximately 4-6
hours. Less time could be needed, depending on the pool size. The
cleaner was not designed to automatically clean steps or swimouts or to
work under a solar cover. It was also not designed to do initial cleanup
for a new pool or when opening your pool for the season.
AFTER installing the cleaner, make sure the cleaner is operating
correctly:
The cleaner may need some minor adjustments to make sure it is
operating properly so there is no damage to the pool finish. Certain
vinyl liner patterns are particularly susceptible to surface wear, pattern
removal, ink rubbing off of, or serious scratches to the pattern caused by
objects coming into contact with the vinyl surface, including automatic
pool cleaners. Pentair Water Pool and Spa, Inc. is not responsible for
any pattern removal, abrasions or markings on vinyl liners.
ENGLISH
Stop pump before attempting to clean unit. Do
not allow swimmers in pool while pool cleaner is
operating.
To reduce the risk of injury, do not let children use
or play with pool cleaner.
Do not allow swimmers in the pool while pool cleaner
is operating. Hose can trip or entangle swimmers
which could result in drowning.
Moving parts may injure hands or fingers. Stop pump
before attempting to clean out pool cleaner head.
Warnings and safety instructions for Pentair Water Pool and Spa,
Inc. pumps and other related products are available at:
http://www.pentairpool.com/pool-owner/safety-warnings/ or call
(800) 831-7133 for additional free copies of these instructions.
Please refer to http://www.pentairpool.com/pool-owner/
safetywarnings/ for warning and safety instructions related to
this product.
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
iii
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
Disclaimer of Liability
About your Pool and Cleaner
There are a multitude of factors that contribute to the life of your pool. The
pool cleaner is a very passive product that will have no impact on pool life.
Please be aware that over time, deterioration, discoloration and brittleness
of any pool finish can be caused separately by, or in combination with,
age, an imbalance in pool water chemistry, improper installation and
other factors. Suction side pool cleaners, such as the pool cleaner, will
not remove or cause wear on “good” pool plaster. In fact, the opposite is
true–pool plaster will eventually cause wear on the cleaner.
The same situation holds true for vinyl-lined in-ground swimming pools,
because vinyl liners are also affected by the environment and factors such
as pool water chemistry, sunlight and the pool’s surroundings. Therefore
over time, vinyl can become brittle and weak. In addition, vinyl-lined pools
are affected by the workmanship, composition and installation of the
liner and the workmanship and quality of construction of the supporting
walls and pool base. These are all factors which can contribute to liner
failure. The existence of any of these type of conditions in your pool is
not caused by the use or operation of the pool cleaner. The manufacturer
disclaims any liability for repairs or replacement to any of these structures
or components of the customer’s pool.
The pool owner must assume all responsibility for the condition and
maintenance of the pool’s surface, water and deck.
Before the cleaner is installed, please take a moment to record the
serial number. This number is located under the rear handle of your
cleaner. You will be asked for this number when you contact our
Technical Support Department.
SERIAL #__________________________________
SAVE THESE INSTRUCTIONS
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
1
POOL PREPARATION
Pool Preparation
Before installing the Warrior™ Suction Side Pool Cleaner, your pool should be clean and algae-free so as to not
inhibit the cleaner’s traction. If necessary, make the following preparations before proceeding:
1. Chemically balance the pool water.
2. Brush pool and let the debris settle.
3. Hand vacuum thoroughly.
4. Clean filter and pump strainer basket.
Cleaner Components
Remove the cleaner and all parts from the box. Check to be sure all components are included.
ENGLISH
1. Warrior cleaner body
2. Hose float
3. Eyeball diverters (2)
4. Valve cap
5. Regulator valve
6. Threaded compression adapter
7. Hose protector
8. Flow gauge
9. Vacuum line door
10. Hose Set – 13 Sections
---12 Standard Male/Female
Hoses
---1 Leader Hose
Figure 1
1.
4.
5.
6.
2.
8.
7.
10.
Standard Hose
Leader Hose
3.
9.
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
2
Male Hose End
Female Hose End
20 in
(50.8 cm)
Hose must reach furthest point in pool
— —
plus one length
plus
leader
hose
ASSEMBLING THE CLEANER
The Warrior™ Suction Side Pool Cleaner body is shipped
as one piece, making cleaner assembly a simple and
quick process.
Hose Assembly
For best results and to maintain proper operation, use
only original Pentair parts and hoses.
1. To connect the hose sections, wet the ends in the
pool water, then twist and push the female ends
onto the male ends.
Figure 2
2. Connect the leader hose to the cleaner swivel.
See Figure 3.
Note: The leader hose is 12 inches (30.5
centimeters) in length and shorter than the other
sections included in the hose set. The leader
hose is also marked with a red sticker. Failure to
use this leader hose section will hinder cleaner
performance
3. The hose should reach from where the cleaner is
connected to the farthest point of the pool, plus
one section and the leader hose.
4. Install the hose float onto the second length of
hose. The float should be placed 20 inches (50.8
centimeters) above the cleaner. See Figure 4.
5. Make sure that all connections are snug.
6. The overall length of hose needed will be
determined by the distance from the point at which
you attach the hose to the suction port to the
furthest point in the pool, plus one length and the
leader hose. Refer to Figure 5.
Figure 3
Leader
Hose
Swivel
Assembly
Figure 4
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
Figure 5
40” Female/
Male Hose
Attach
Hose
This End
Top of Skimmer
Hose through
Skimmer
Opening
Regulator
Valve
Threaded
Compression Adapter
To Pump
Hose
Protector
e
Standard Installation
The Warrior™ Suction Side Pool Cleaner is designed
to work in a wide variety of swimming pools. Both the
standard in-skimmer installation and optional vacuum
line installation are covered in this section. Check to
see which most closely fits your pool configuration and
follow the directions.
Note: Depending on the particular features of your
pool, the valve cap for the regulator valve may not be
needed.
1. Turn the pool pump off.
2. Close the main drain and all suction lines, except
the line from the skimmer to which the cleaner will
be connected.
3. Remove skimmer basket.
4. Thread the compression adapter into the vacuum
connection in the bottom of the skimmer. See
Figure 7.
Note: Use two wraps of thread seal tape around
threads to ensure easy removal.
5. Press the regulator valve into the compression
adapter. The valve’s adjustment knob should be
pointing up.
6. Place cleaner into the pool. Turn it side to side
and front to back to release any trapped air,
allowing the cleaner to sink to the floor of the pool.
Continue to feed the hose vertically down into
the pool until it is completely filled with water and
purged of air.
Note: If air is pulled into the pool plumbing it may
cause your pump to lose prime.
7. Slide the hose protector into position on the hose
to prevent the hose body from rubbing against the
skimmer wall.
8. Insert the end of the hose through the skimmer
opening and connect the hose directly onto the
regulator valve. See Figure 7.
3
INSTALLING THE CLEANER
Figure 6
Attach Hose This End
Regulator
Valve
Couple Wraps
of Thread Tap
Threaded
Compression
Adapter
Thread into
bottom of skimmer
Figure 7
ENGLISH
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
4
Optional Vacuum Line Installation
Vacuum Line Installation with Regulator Valve in
Skimmer.
We highly recommend the use of the regulator
valve to balance water flow between the Warrior™
Suction Side Pool Cleaner and the skimmer. Install
the regulator valve in the skimmer when attaching
the cleaner to a dedicated vacuum line.
1. Turn the pool pump off.
2. Close the main drain and all suction lines, except the
lines from the skimmer and the suction line to which
the cleaner will be connected.
3. Thread the snap-lock wall fitting into the end of the
dedicated suction line.
Note: Use two wraps of thread seal tape around the
threads to ensure easy removal.
4. Place the cleaner (with the hose attached) into the
pool. Turn it side to side and front to back to release
any trapped air, allowing the cleaner to sink to the
floor of the pool. Continue to feed the hose vertically
down into the pool until it is completely filled with
water and purged of air.
Note: If air is pulled into the pool plumbing it may
cause your pump to lose prime.
5. Insert the male hose end of the last hose section
directly into the snap-lock wall fitting. See Figure 8.
6. Thread the compression adapter into the vacuum
connection in the bottom of the skimmer.
7. To prevent water from flowing through the top of the
regulator valve, fasten the valve cap onto the top of
the valve (See Figure 9). This activates the regulator
valve and assures that an accurate amount of water
(25 GPM) will flow through the vacuum line and the
cleaner. Without the valve cap, the regulator valve and
the cleaner will not function properly. See Figure 10.
8. Press the regulator valve into the compression
adapter.
Snap-Lock
Wall Fitting
Male/Female
Hose Section
Valve Cap
Regulator
Valve
Threaded
Compression
Adapter
Top of Skimmer
Figure 8
Thread Snap-Lock
into Dedicated
Suction Line
in Pool Wall
Figure 9
Couple Wraps
of Thread Tape
Thread into
bottom of skimmer
Figure 10
Valve Cap
Installed
After completing the installation, turn the pool pump
on. Allow the pump to run for a couple of minutes to
be sure all air cycles out of the system.
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
Regulator
Valve
Threaded
Compression
Adapter
To Pump
5
Adjusting Flow to the Cleaner With the Flow Gauge
1. Turn the pool pump off.
2. Disconnect the Warrior™ Suction Side Cleaner from the leader hose and
connect the flow gauge.
Note: Make sure the hose remains submerged to prevent suction of air.
3. Turn the pump on.
4. Turn the regulator valve adjustment knob clockwise to increase flow or
counterclockwise to decrease flow, until the disc indicator in the flow gauge
settles between “Maximum” and “Minimum” flow. See Figure 11.
5. Turn the pool pump off and remove the flow gauge and reconnect the
cleaner.
6. Lower the cleaner in to the pool and allow it to drop to the pool floor.
7. Turn the pool pump on.
Figure 11
Calculating Cleaner Speed (RPM) Without the Flow Gauge
If you do not have the flow gauge originally included with your cleaner, following the steps below will allow you
to calculate the cleaner speed and adjust RPM as needed.
1. While the cleaner is running, bring the cleaner up to just beneath the pool’s water surface.
Note: Be sure to keep the cleaner submerged while the pump is operating. This prevents the cleaner from
pulling air into the pool system.
2. Count the number of full rotations made by the wheel over a period of one minute. The number of rotations
will give you the revolutions per minute; or RPM’s. An easy way to be sure you are counting full rotations is
by counting the number of times the wheel hump passes by the swivel assembly.
3. For proper performance, the Warrior cleaner operates between 11-13 RPM.
If the RPM is below 11 adjust the regulator valve (rotate adjustment knob clockwise) and repeat steps 1-2
until the RPM falls back into the optimal range.
If the RPM is higher than 13 adjust the regulator valve (rotate adjustment knob counterclockwise) and repeat
steps 1-2 until the RPM falls back into the optimal range.
ENGLISH
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
6
Hose must reach furthest point in pool
— —
plus one length
plus
leader
hose
CLEANER ADJUSTMENTS AND OPERATION
After installation, turn the pool pump on. The Warrior™ Suction Side Pool Cleaner should be moving about the
pool at a rate of 8 to 12 feet per minute. Be sure to check each of the following initial adjustments.
Hose Length
Note: The pump must be on when you check the
hose length. The hose contracts when the pump is
operating and will be longer when the pump is off.
While the cleaner is operating:
1. Position cleaner at the furthest point of the
pool from where it’s attached. Use a pool
pole and brush to easily position the cleaner
in the pool.
2. The hose should be long enough to reach the
end of the pool, plus one hose section and
the leader hose. See Figure 12.
3. Remove any excess hose lengths from the
middle of the hose assembly. This will ensure
you do not alter the position of the hose float.
4. Save extra hose sections for use as needed
for replacement.
Note: Turn pool pump off when adding or
removing hose sections.
Figure 12
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
7
Pool Deck
Wire Diveter (optional)
P/N K121620
Eyeball Diveter
P/N 41201-0236
Pool Wall
Retur
n
Line
Eyeball
Fitting
Eyeball Diverter
Lock
(Retaining)
Ring
BEFORE ADJUSTMENT
AFTER ADJUSTMENT
TOP VIEW SIDE VIEW
TOP VIEW SIDE VIEW
Return Line Water Flow
IMPORTANT: The water flow from your return line can push the Warrior™ Suction Side Pool Cleaner’s hose and affect
its performance. It may cause the cleaner to steer away from the end of the pool where the return line is located, or
it may cause your cleaner to remain in one section of the pool. To correct this, use the eyeball diverter included. If
the eyeball does not fit your pool, use the wire diverter.
(P/N K121620) Wire diverter available for purchase from your Pentair Aquatic’s dealer.
To install the eyeball diverter:
• First make sure your pool pump is off. Remove the
original eyeball from the return line at the pool by
unscrewing the lock ring.
• Replace the original eyeball with the eyeball diverter
that came with your Warrior cleaner.
• Replace the lock ring and tighten. Make sure the
opening of the eyeball diverter points in the proper
direction before tightening fully.
Figure 13
ENGLISH
Eyeball Diverter Positions
Position the diverter opening to redirect the return line
water flow so it does not interfere with the cleaner’s
movement. Try different positions to see which works
best in your pool:
• flow directed along the side of pool (the tile line).
• flow directed downward.
• flow directed against the hose will help steer the
cleaner away from obstructions such as stairs and
ladders.
After installing the eyeball diverter, turn the pool pump
on. The cleaner should begin moving across the pool
floor vacuuming up debris in its path.
Figure 14
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
8
MAINTENANCE
The Warrior™ Suction Side Pool Cleaner requires almost no
maintenance. Visually inspect your cleaner from time to time to
make sure that:
• The turbine is moving freely and is not obstructed by debris.
See “Removing Debris from the Turbine” below.
• The tires are not excessively worn. See Figure 18 on the
next page.
We recommend that you leave the cleaner in your pool, except
during chemical shock treatments.
• During swimming it is easy to unplug the cleaner and pull
it to one side.
• Note: When storing the cleaner, do not coil the hose. Lay
the hose flat in an area protected from direct sunlight.
This cleaner’s hose is specially designed to ensure optimum
cleaner performance. Should replacement be required, insist
on genuine Pentair cleaner hose.
Removing Debris from the Turbine
1. Be sure the pool pump is off. Remove the cleaner from the
pool and disconnect the cleaner from the leader hose.
2. Check to see if anything is clogged inside the cleaner. Do
this by positioning the cleaner with the buckle facing you
and attempt to rotate the right side wheel forward. If the
wheel rotates smoothly there probably is no obstruction. If
it won’t rotate there is an obstruction.
3. Place the cleaner on a flat work surface. Open the buckle
on the front of the cleaner by pulling it out and down.
Lift the front of the top cover up and then firmly pull it
forward. This will separate the top cover from the cleaner
body and you will now be able to lift the top cover straight
up from the cleaner body (see Figure 15). Set the cover
aside.
Note: The top cover is designed to fit tightly so you may
have to wiggle it a little.
4. Pull the turbine cover straight up and off of the cleaner
body. Set the turbine cover aside. See Figure 16.
5. Remove any visible obstructions from the turbine and
turbine cover.
6. Replace the turbine cover with the swivel assembly
oriented towards the front of the cleaner. See Figure 16.
7. Visually inspect the rest of the cleaner and remove any
debris that may be in the gears, drive shafts, swivel
assembly, etc.
8. Repeat step 2 (turning the right wheel) to insure that the
cleaner runs smoothly.
9. Place the top cover over the swivel assembly.
10. Place the tabs on the back side of the top cover into the
slots on the back side of the cleaner body (see Figure 17).
Once these tabs are seated in the slots the front of the
cover will fall into place.
11. Lock the top cover onto the cleaner body with the locking
buckle on the front of the cleaner.
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
Figure 15
Top Cover
Right Side
Wheel
Buckle
Removal of Top Cover
Turbine
Cover
Swivel
Assembly
Figure 16
Swivel Assembly and Cleaner Internals
Figure 17
Top Cover
Ta b
Cleaner
Body Slot
Cover Tabs and Corresponding Body Slots
9
Tire Replacement
After prolonged use it may become necessary to replace the Warrior™ Suction Side Pool Cleaner’s rubber tires.
When the tire surface has worn into the tire’s grooves the tire is in need of replacement. See Figure 18.
To remove the cleaner tire:
1. Turn the pool pump off and remove the cleaner from the pool.
2. Disconnect the cleaner from the leader hose.
3. Place the cleaner on a flat work surface and fold the tire off of the wheel from top to bottom.
Note: Remove the tire by hand. Using other objects (screwdrivers, Allen keys, etc.) to remove the tire may
damage the wheel.
New Tire: Outer
surface of the tire
is well above the
bottom of the tire’s
grooves.
Figure 18: Tire Wear Comparison
To install the replacement tire:
1. Place the cleaner on a flat work surface and seat the top of the rubber tire onto the top of the wheel. Be sure
that the back lip of the tire is resting flat on the inside edge of the wheel.
Note: Replace the tire by hand. Using other objects (screwdrivers, Allen keys, etc.) to replace the tire may damage
the wheel.
2. Stretch the bottom of the tire over the bottom of the wheel. Be sure that the back lip of the tire is resting flat on
the inside edge of the wheel.
3. Fold the back lip of the tire onto the back of the cleaner wheel along the entire cleaner wheel. The tire should lie
flat on the top surface of the wheel.
Excessively
Worn Tire: Outer
surface of the tire
has nearly worn
to the bottom of
the tire’s grooves.
ENGLISH
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
10
TROUBLESHOOTING
Because of the individual characteristics of your pool, some additional adjustments may be required to get the best performance
from your Warrior™ Suction Side Pool Cleaner. Use the following information to resolve possible issues.
PROBLEM CORRECTIVE ACTION
Cleaner is not moving or is moving
too slowly.
Cleaner’s right wheel will not turn when
rotated by hand.
Cleaner stays in one end of the pool.
Cleaner climbs the wall too much or climbs
out of pool.
Check flow with flow gauge included or by calculating the cleaner RPM and adjust the flow
if necessary using the regulator valve. See page 5.
Check for debris inside the cleaner itself. See page 8.
Check to be sure the pump has primed. Check for leaks in the system that may prevent
proper priming.
There may not be enough flow through the system. The filter may need backwashing.
Check to be sure that the main drain and all suction lines are closed, except for the suction
line to which the cleaner is attached.
Check for obstructions in the system (e.g. debris in the filter, pump basket or pump
impeller).
Pool pump and filter system may be too small to provide proper water flow. Consult your
pool professional.
Check for obstructions inside the cleaner itself. See page 8.
Check flow with flow gauge included or by calculating the cleaner RPM and adjust the flow
if necessary using the regulator valve. See page 5.
Check the return line water flow and redirect as necessary with the included eyeball
diverter. See page 7.
Check that hose is long enough to reach the furthest point in the pool. See page 6.
Check for proper hose float placement. The float may be in the wrong position. See page 2.
Be sure that the swivel assembly (at top of cleaner) rotates smoothly. If not, the swivel
assembly may be dirty and require cleaning.
Check flow with flow gauge included or by calculating the cleaner RPM and adjust the flow
if necessary using the regulator valve. See page 5.
Cleaner won’t climb the pool walls.
Cleaner stays on the main drain.
Cleaner falls on its side and takes too long to
recover.
Check to be sure that the cleaner tires are not excessively worn. See page 9. Excessively
worn tires will not provide the grip necessary for your cleaner to climb pool walls.
Check flow with flow gauge included or by calculating the cleaner RPM and adjust the flow
if necessary using the regulator valve. See page 5.
Check to be sure that the leader hose has been installed and is in the correct location. See
page 2.
Check for proper hose float placement. The float may be in the wrong position. See page 2.
Check to be sure that main drain is closed. May need assistance from a pool professional.
Check to be sure a main drain grate is installed.
Check for proper hose float placement. The float may be in the wrong position. See page 2.
Check to be sure that the leader hose has been installed and is in the correct location. See
page 2.
Check that the hose is long enough to reach the furthest point in the pool. See page 6.
The return eyeball fittings may be pushing the cleaner hoses away. See page 7.
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
11
16
1
1
2
3
4
5
5
4
6
6
7
8
9
10
11
12
13
14
15
16
17
25
18
21
20
19
Item
Number
P/N DESCRIPTION
1 360304 Top Cover Kit
2 360305 Buckle Kit
3 360285 Swivel Kit
4 360306 Wheel Kit
5 360287 Tire Kit
6 360288 Wheel Hub Kit
7 360289 Left Drive Kit
8 360290 Right Drive Kit
9 360291 Bottom Cover Kit
10 360292 Drive Gear Kit
11 360293 Turbine Kit
12 360294 Cam Kit
13 360295 Cam Gear Kit
14 360296 Front Roller Kit
Item
Number
P/N DESCRIPTION
15 360297 Rear Roller Kit
16 360298
Roller Bar Kit
17 360299
Wear Bar Kit
18 41200-0211
Valve Cap
19 41200-0200
Regulator Valve
20 K70079
Threaded Compression Adapter
21 41200-0210
Flow Gauge
*22 GW9530
Vacuum Line Door
*23 41201-0236
Eyeball Diverter (x2)
*24 K60465
Hose Protector
25 360317
Hose Float
*26 360309
Hose Set
*27 360308
Leader Hose
REPLACEMENT PARTS
ENGLISH
KREEPY KRAULY® WARRIOR™ Suction Side Pool Cleaner Installation and User’s Guide
Note: (*) Not Shown
Loading...