®
KREEPY KRAULY
RACER
PRESSURE SIDE POOL CLEANER
™
ENGLISH 1
ESPAÑOL 17
INSTALLATION AND
USER’S GUIDE
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
FRANÇAIS 37
SAVE THESE INSTRUCTIONS
i
CUSTOMER SERVICE / TECHNICAL SUPPORT
If you have questions about ordering Pentair Aquatic Systems replacement parts, and pool products, please contact:
Customer Service and Technical Support, USA
(8 A.M. to 5 P.M. — Eastern/Pacific Times)
Phone: (800) 831-7133
Fax: (800) 284-4151
Web site
Visit www.pentairpool.com or www.staritepool.com
TABLE OF CONTENTS
Important Warning and
Safety Instructions ..............................................
Important Information ..........................................
Cleaner Components
Overview
Installation ...........................................................
Booster Pump Installation
Installing the Wall Fitting and Adapter
Setting the Water Flow to Cleaner
Calculating Cleaner Speed/RPM
Adjusting the Hoses to Fit Pool
Assembling the Cleaner
Using the Cleaner
Cleaner Adjustments and Operation ..................
Cleaner Operation
Adjusting the Thrust Jet
Cleaning the Debris Bag
Adjusting the Sweep Hose Regulator
Sanford, North Carolina (8 A.M. to 5 P.M. ET)
Phone: (919) 566-8000
Fax: (919) 566-8920
Moorpark, California (8 A.M. to 5 P.M. PT)
Phone: (805) 553-5000 (Ext. 5591)
Fax: (805) 553-5515
Maintenance .........................................................
ii
1
1
1
2
2
2
2
3
4
6
Wall Fitting Screen
Tires
Roller Rings
Debris Bags
Sweep Hose
Backwashing the Pool Filter
Storage and Winterizing
Replacement Parts ..............................................
Parts List
Troubleshooting ....................................................
Steep Vinyl Liner Transitions
6
7
7
7
8
9
10
10
10
10
10
10
10
10
12
13
14
16
© 2014 Pentair Water Pool and Spa, Inc. All rights reserved.
This document is subject to change without notice.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000
All Pentair trademarks and logos are owned by Pentair or one of its global affiliates. Pentair Aquatic Systems™, Kreepy
Krauly®, Night Cruize® and RACER™ are trademarks and/or registered trademarks of Pentair Water Pool and Spa, Inc. and/
or its affiliated companies in the United States and/ or other countries. Unless expressly noted, names and brands of third
parties that may be used in this document are not used to indicate an affiliation or endorsement between the owners of these
names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be the trademarks or registered
trademarks of those third parties. Because we are continuously improving our products and services, Pentair reserves the
right to change specifications without prior notice. Pentair is an equal opportunity employer.
P/N 371004 Rev. B 6/11/14
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
ii
Important Notice:
Attention Installer: This guide contains important information about the
installation, operation and safe use of this product. This information should
be given to the owner and/or operator of this equipment after installation
of the pool cleaner.
Attention User: This manual contains important information that will help
you in operating and maintaining this pool cleaner. Please retain it for future
reference. Consult Pentair with any questions regarding this equipment.
Before installing this product, read and follow all
warning notices and instructions which are included.
Failure to follow safety warnings and instructions can result in severe
injury, death, or property damage. Call (800) 831-7133 for additional free
copies of these instructions.
Consumer Information and Safety
This pool cleaner is designed and manufactured to provide many years
of safe and reliable service when installed, operated and maintained
according to the information in this manual. Throughout the manual, safety
warnings and cautions are identified by the “ ” symbol. Be sure to read
and comply with all of the warnings and cautions.
HAZARDOUS SUCTION.
Do not play with cleaner or hose or apply to body.
Can trap and tear hair or body parts. Hose can trip or
entangle swimmers which could result in drowning.
SUCTION ENTRAPMENT, INJURY, AND
DROWNING HAZARD. If your pool has a dedicated
suction port (“vac port”) for vacuuming or for an
automatic pool cleaner, it must be covered when
not in use. A spring loaded safety cover (a “vac port
fitting”) is included with your cleaner. Install it on the
suction port to prevent entrapment and injury. If the
cover provided does not fit, purchase one that does
from your local pool store and install it instead. The
cover should conform to IAPMO SPS4-99A.
Stop pump before attempting to clean unit. Do
not allow swimmers in pool while pool cleaner is
operating.
To reduce the risk of injury, do not let children use
or play with pool cleaner.
Do not allow swimmers in the pool while pool cleaner
is operating. Hose can trip or entangle
swimmers which could result in drowning.
Moving parts may injure hands or fingers. Stop pump
before attempting to clean out pool cleaner head.
General Installation Information
Pre-Installation Check List
Before installing your cleaner, review and understand all warnings and
safety information in this guide. Failure to follow these instructions or
improper installation of the cleaner can result in damage to the pool
finish or the vinyl liner, Most cleaners are not designed to traverse from
floor to wall when the pool cove is 90%. There may be other structures
installed in the pool that the cleaner cannot navigate, BE AWARE and
supervise the cleaner during unique conditions. Pentair Aquatic Systems
disclaims any liability for repairs or replacement to any of these structures
or components of the customer’s pool.
Before installing the cleaner in a vinyl liner pool:
Check liner closely for signs of deterioration or damage from age,
chemicals, pool wall damage, etc. If any damage is found, have a qualified
pool professional make all the necessary repairs. Also, if there are stones,
roots, etc., under the liner, remove them before installing the cleaner.
Before installing the cleaner in a gunite pool or a pool that is partially
or completely tiled:
Make sure pool finish is in proper condition as staining, etching, cracking
or delaminating may worsen.
Repair loose tiles and tighten any loose light rings.
Before installing the cleaner, clean your filter system:
Make sure you have cleaned the filter, including backwashing, rinsing,
and emptying all baskets. A clean system is necessary for proper cleaner
operation and coverage.
Before installing the cleaner, understand cleaner coverage:
The cleaner is designed to rid your pool of debris in approximately 4-6
hours. Less time could be needed, depending on the pool size. The cleaner
was not designed to automatically clean steps or swimouts, or to work
under a solar cover. The cleaner may get stuck in these areas which can
result in damage to the pool finish or vinyl liner. Pentair Aquatic Systems
disclaims any liability for repairs or replacement to any of these structures
or components of the consumer’s pool. It was also not designed to do
initial cleanup for a new pool or when opening your pool for the season.
AFTER installing the cleaner, make sure the cleaner is operating
correctly:
The cleaner may need some minor adjustments to make sure it is
operating properly so there is no damage to the pool finish. Certain
vinyl liner patterns are particularly susceptible to surface wear, pattern
removal, ink rubbing off of, or serious scratches to the pattern caused by
objects coming into contact with the vinyl surface, including automatic
pool cleaners. Pentair Aquatic Systems is not responsible for any pattern
removal, abrasions or markings on vinyl liners. Periodically inspect the
cleaner components and the cleaner performance to ensure it is operating
as designed. Replace and/or repair any worn or damages components.
Failure to follow instructions or improper installation of the cleaner may
result in damage to the cleaner, pool finish or the vinyl liner.
Warnings and safety instructions for Pentair Aquatic Systems
pumps and other related products are available at:
http://www.pentairpool.com/pool-owner/safety-warnings/ or call
(800) 831-7133 for additional free copies of these instructions.
Please refer to http://www.pentairpool.com/pool-owner/
safetywarnings/ for warning and safety instructions related to
this product.
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
ENGLISH
ESPAÑOL 20
FRANÇAIS 43
iii
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
Disclaimer of Liability
About your Pool and Pressure Side Pool Cleaner
There are a multitude of factors that contribute to the life of your pool. The
pool cleaner is a very passive product that will have no impact on pool life.
Please be aware that over time, deterioration, discoloration and brittleness
of any pool finish can be caused separately by, or in combination with,
age, an imbalance in pool water chemistry, improper installation and other
factors. Pressure side pool cleaners will not remove or cause wear on
“good” pool plaster. In fact, the opposite is true–pool plaster will eventually
cause wear on the cleaner.
The same situation holds true for vinyl-lined in-ground swimming pools,
because vinyl liners are also affected by the environment and factors such
as pool water chemistry, sunlight and the pool’s surroundings. Therefore
over time, vinyl can become brittle and weak. In addition, vinyl-lined pools
are affected by the workmanship, composition and installation of the
liner and the workmanship and quality of construction of the supporting
walls and pool base. These are all factors which can contribute to liner
failure. The existence of any of these type of conditions in your pool is
not caused by the use or operation of the pool cleaner. The manufacturer
disclaims any liability for repairs or replacement to any of these structures
or components of the customer’s pool.
The pool owner must assume all responsibility for the condition and
maintenance of the pool’s surface, water and deck.
Before the cleaner is installed, please take a moment to record the
serial number. This number is located on your warranty card and
on the back of the cleaner near the rear jets. You will be asked for
this number when you contact our Technical Support Department.
SERIAL #__________________________________
SAVE THESE INSTRUCTIONS
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
1
OVERVIEW
Cleaner Components
1. RACER Cleaner Head
2. Debris Bag
3. Sweep Hose (not needed
in most pools)
4. Feed Hose Assembly - Not
shown (3-10 ft. sections)
5. Wall Fitting
6. Wall Adapter
7. Debris Seal
Note: The cleaner system is delivered
with debris seal installed inside of
cleaner head.
8. Flow Gauge
Overview
The RACER™ Pressure Side Pool Cleaner moves
through a sequence of straight, right and left turns
helping to increase pool coverage, vacuuming and
scrubbing your entire pool.
• For continuous uninterrupted cleaning, the cleaner
will go into reverse mode about every two minutes,
which allows it to efficiently clean the entire pool.
6
5
8
2
7
3
ENGLISH
1
ESPAÑOL 20
Night Cruize ® LED
FRANÇAIS 43
Note: Before you install and operate your cleaner,
read through these important guidelines:
1. Always disconnect the cleaner from the pool wall
when cleaning or back washing the pool filter.
2. After cleaning or back washing the filter, let the
filtration system run for at least five minutes before
reconnecting the cleaner.
3. New plumbing lines should be flushed out before
installing the cleaner.
4. The cleaner should not be used to remove plaster
dust in new pools.
5. Always remove the cleaner before swimmers enter
the pool.
6. Always handle the cleaner with care.
7. Always pick up the cleaner by the handle,
especially when lifting the unit out of the water.
8. Do not handle the cleaner while it is operating.
9. Always remove the cleaner from the pool before
chemical shock treatments (super chlorinate). As a
rule, any pool water that is unsafe for swimming is
unsafe for the cleaner.
10. Carefully cut the feed hose following the
instructions on page 4.
11. By following these simple guidelines, you can help
protect against injury and prolong the life of your
cleaner.
12. Refer to “Important Warning And Safety
Instructions” on pages ii - iii for additional
installation and safety information.
13. Before you install your RACER pool cleaner:
If there is a chlorinator, solar system, ozone
generator or air inducing equipment installed,
contact Technical Support at 1-800-831-7133.
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
2
INSTALLATION
Booster Pump Installation
Please refer to the instructions included with your
booster pump for installation information.
Please follow these instructions carefully.
Installing the Wall Fitting and Wall Adapter
Wall Adapter
(Shown Installed)
1. Remove and disconnect any existing pool cleaner
and/or wall fitting.
2. Switch on the filtration pump and booster pump, to
flush out the plumbing line.
3. Switch off filter pump and booster pump.
4. Insert wall fitting adapter into the dedicated 1-1/2”
NPT threaded return line. Hand tighten until snug.
See figure 3.
5. Align wall fitting with the quick lock pegs inside the
wall adapter. Push the wall fitting into the wall adapter
until it bottoms out. Twist 1/4 turn clockwise to lock
the wall fitting. Pull gently outward to engage quick
lock pegs. See figure 3.
Setting the Water Flow to the Cleaner
IMPORTANT! Before starting this procedure
be sure to switch off the filter pump and
booster pump.
1. Attach the flow gauge to the wall fitting by aligning the two
tabs on the flow gauge with the grooves in the wall fitting.
See figure 4. Push and turn the flow gauge clockwise until
it stops, then slightly pull it out away from the wall. Be
sure the flow gauge is securely locked in place by turning
it counterclockwise while slightly pulling out on the flow
gauge. See figure 5.
Note: Flow gauge will not turn when locked in place.
2. Switch on the filter pump and then the booster pump.
3. Verify the white plunger (inside the flow gauge) is aligned
within the box on the flow gauge. See figure 6.
4. Adjust the valve on the wall fitting using a flathead screw
driver by turning the valve clockwise (to reduce flow) or
counter-clockwise (to increase flow) so that the white
plunger aligns with the arrows on the flow gauge markings.
See figure 7.
5. Switch off the booster pump and then the filter pump.
6. Remove the flow gauge from the wall fitting by pushing in
and turning counterclockwise and pulling the gauge out.
7. Attach the hose assembly to the wall fitting. Turn clockwise
then push in one quarter turn to secure in place (as
described in Step 2).
Quick
Lock Peg
Figure 3.
Figure 4.
Figure 5.
Wall Fitting
LOW
HI
O-Ring
Installing the Wall Fitting
Wall Fitting
Flow Gauge
Align Tabs
Wall Fitting
Max Flow
Min Flow
Turn counterclockwise
to OPEN
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
Figure 6. Figure 7.
3
Calculating Cleaner Speed/RPM
1. To determine whether the RACER™ Pressure Side Pool Cleaner is receiving the proper water pressure,
turn off the pool pump, and carefully remove the cleaner from the pool.
2. Mark the front tire/wheel with a marker, such as a blade of grass stuck under the tire.
3. Have someone restart the pool pump and booster pump while you place the cleaner just beneath the
pool’s water surface.
Note: Be sure to hold onto the sweep hose (if installed) to avoid getting wet, as flow will return to the
sweep hose regulator when the pump is restarted.
4. Count the number of full rotations made by the marked wheel over a period of one minute. The number of
rotations will give you the revolutions per minute; or RPM’s.
Note: Be sure that the back-up valve isn’t cycling at this time.
5. For proper performance, the RACER cleaner operates between 31 - 33 RPM’s with a sweep hose
installed and 33 - 36 RPM’s without a sweep hose.
If the RPM is below 31 with a sweep hose installed, or below 33 without a sweep hose, then call your
local Pool Professional or contact Pentair’s Technical Support Department at 1-800-831-7133.
If the RPM is higher than 33 with a sweep hose installed, or higher than 36 without a sweep hose, at the
wall fitting adjust the valve, as described under “Setting the Water Flow to the Cleaner” on page 2, until
the RPM falls back into the optimal range.
ENGLISH
ESPAÑOL 20
Cleaner Body
FRANÇAIS 43
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
4
Adjusting the Hose Assembly to Fit Pool
The hose assembly consists of: Three (3) 10 ft.
sections, one (1) soft light grey lead hose marked as
section one and two (2) stiffer dark grey feed hoses
marked as sections two and three.
Important to the Performance of the Cleaner:
Measure, cut, and assemble the hose sections as
described in Step 1 and Step 2. Use strong scissors
or a sharp knife to cut the hoses. Be sure to slide the
floats out of the way when cutting hose. Cut hose ends
as straight as possible.
Step 1: Sizing Hose Section 1
1. Measure the deepest part of the pool. See figure
8.
Note: The grate or domed main drain, at the
bottom of the pool, is usually the deepest point. If
the depth is greater than 10 ft., do not cut the hose,
and proceed to Step 2.
2. If the pool depth is less than 10 ft., disconnect the
soft light grey lead hose, labeled section one, from
the swivel end. Cut the lead hose so the length is
equal to the deepest part of the pool. See figure 9.
Example: If the pool is 8½ ft. deep, cut 1½ ft. off of
the hose labelled section one (since the hose is 10
ft.).
3. Discard excess hose. Reconnect the newly cut lead
hose to the swivel on the feed hose. All three hose
sections should now be connected.
Figure 9.
Measure Deepest Part of Pool
Main Drain
Figure 8.
Lead Hose Length = Deepest Part of Pool
Swivel
Float
Quick
Connect Fitting
(connects to
Measuring the Lead Hose
cleaner)
Wall Fitting
Hose Assembly
Step 2: Sizing Hose Sections 2 and 3
1. Attach the hose assembly to the wall fitting. See
figure 10. Then attach the wall fitting (with hose) to
the wall adaptor. See figure 10. Take the opposite end
of the hose assembly and walk to the farthest point
of the pool from the wall adaptor. To prevent over
stretching the hose, rest the hose on top of the
pool water. Measure the excess hose length (hose
that extends beyond pool edge). This determines
the amount of hose to be cut from sections 2 and 3.
2. Disconnect feed hose assembly from the wall adaptor.
Disconnect sections 2 and 3 from the first swivel
closest to the wall fitting.
3. Cut half of the total excess hose length from each
hose labeled section 2 and section 3 (assembled
with four floats) equally. Both feed hose sections
should be the same length after cutting.
Example: If there is 6 ft. of excess hose. Cut 3 ft. off
of section 2 and section 3. (Half of 6 ft. = 3 ft. each)
If more than 3 ft. is cut from each hose section, remove
one (1) float from each hose section.
Note: For large pools requiring extra hose lengths
you will need to purchase one (1) additional hose,
P/N 360265 (10 ft. single hose). Attach extra hose
sections at the wall fitting using supplied swivel and
mender nuts.
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
Figure 10.
WALL FITTING
SWIVEL
FLOATS
10 FOOT (3 METER)
WHITE OR GREY
HOSE SECTION
MARKED SWIVEL
10 FOOT (3 METER)
WHITE OR GREY
HOSE SECTION
10 FOOT (3 METER)
SOFT HOSE
FARTHEST POINT OF POOL PERIMETER FROM WALL FITTING
Figure 11.
FLOATS
SWIVEL
REMOVE EXCESS MATERIAL
FROM HOSE ON EITHER SIDE OF
MARKED SWIVEL AS DESCRIBED
IN STEPS 2 AND 3.
FLOATS
7½ FT. (2,3 M.)
EXAMPLE DIMENSION
(Your Measurement May Differ)
NOT TO SCALE
Step 3: Connecting Hose Sections
1. After the hose sections have been cut to size,
reconnect them by pushing the hose end over
the barb on the swivel.
Note: Be sure to push the hose all the way to
the bottom of the barb.
2. Move the mender nut toward the hose by turning
clockwise and rotating until tight on hose. Use
pliers if needed.
Note: Be sure the same number of floats are left
on hose sections 2 and 3, as described in Step 2
on page 4.
3. To check that the hose is cut to the correct
length, reconnect the hose and wall fitting to the
wall adaptor. Take the opposite end of the hose
assembly and walk to the farthest point of the
pool from the wall adaptor. The hose should
reach the edge of the pool but should not extend
more than 6 inches beyond the pool edge.
4. You can now connect the cleaner to the hose.
5
Feed
Hose
Figure 12.
Barb on
Swivel
Connecting the Hoses to Swivels
Mender Nut
WATER FLOW
DIRECTION
ENGLISH
ESPAÑOL 20
First Swivel
Second Swivel
Wall Fitting
FRANÇAIS 43
Feed Hose
(1)
Feed Hose
(2)
Lead
Hose
Furthest Point of
Figure 13.
Pool Perimeter
Measuring the Feed Hoses
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
6
Assembling the Cleaner
1. Attach the Quick Connect fitting on the end of the hose to the feed tube on the RACER™ Pressure Side Pool
Cleaner. Be sure the snaps are engaged.
2. Attach the debris bag to the cleaner. Push the bag over vacuum tube to click it into place.
3. Review checklist before use:
• Hoses cut properly and floats evenly spaced.
• Mender nuts are tight on feed hose.
• Wall fitting secure and in place.
• Debris bag and hose assembly attached.
• Ensure debris seal is attached. See figure 14.
Using the Cleaner
1. Lower the cleaner carefully into pool.
2. Switch ON the FILTER PUMP.
3. Wait at least 60 seconds to allow air to blow out of the hose.
4. Switch ON the BOOSTER PUMP.
Debris Bag
Quick Connect Fitting
(with built-in swivel)
Optional
Sweep Hose
Lead Hose
Mender Nut
Feed Tube
Debris Seal
Figure 14.
Feed Tube
Debris Seal
Night Cruize® (both sides)
Assembling the Cleaner
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
7
CLEANER ADJUSTMENTS AND OPERATION
Cleaner Operation
Note: The RACER™ Pressure Side Pool Cleaner may need some minor adjustments to ensure it is operating properly
and to get the best performance possible.
When operating correctly, the cleaner will travel in a random pattern throughout the pool, vacuuming and scrubbing
the pool.
• The climbing ability of the cleaner depends on the pool structure and water flow.
• One hour cleaning cycle is recommended for average size residential (15’ x 30’) pools.
• It will perform more efficiently in pools without sharp transitions between pool floor and walls.
• The cleaner goes into a reverse mode approximately every 2-1/2 minutes for approximately 15 seconds.
• If pool has a high level of debris, run the cleaner in two short cycles. Empty the debris bag between cycles.
Adjusting the Thrust Jet
The thrust jet is at the back of the cleaner below the sweep hose regulator, and helps to power the direction of the
cleaner. See figure 15.
You may need to adjust the thrust jet based on the pool shape, in order to get maximum cleaner coverage.
The alternate jet position shown below can help the climbing ability of the cleaner.
ENGLISH
ESPAÑOL 20
Sweep Hose
Regulator
Thrust Jet
Figure 15.
e
n
a
e
l
C
s
e
v
I
o
M
93
D
Factory Jet Position
Straight Out
M
o
t
f
v
e
e
L
r
e
r
c
n
e
c
r
s
C
12
s
C
e
l
s
i
m
a
b
i
n
g
n
i
b
m
e
i
l
a
C
s
e
s
6
9
Alternate Jet Position
10 o-clock Position
l
e
a
n
e
r
R
i
g
h
t
g
FRANÇAIS 43
12
3
6
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
8
Cleaning the Debris Bag
1. Detach the bag strap from the hose.
2. Press the release button on the cleaner vacuum tube and carefully pull up to remove the bag from the cleaner.
See figure 16.
3. Open bag closure by pulling apart the fabric tabs at the top of the bag. Holding the bottom of the bag, turn
over to empty debris out of the top. If needed, rinse bag with a hose.
4. To close, press together the hook and loop fabric at the top of the bag and run finger along entire length of
bag so it is completely closed.
5. Be sure debris seal is on the vacuum tube. See figure 14 on page 6.
6. Slide the debris bag collar over the vacuum tube until it clicks in place.
7. Reattach the strap onto the feed hose.
8. To keep bag from folding during operation, attach the strap above first feed line float. Slide float down if needed.
Note: It is easier to empty the debris bag when it is dry. A second bag (purchased separately) may be used
while the used debris bag is drying.
Use tabs to pull
bag apart
Figure 16.
Debris Bag
Bag Release
Button
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
9
Adjusting the Sweep Hose Regulator when
Sweep Hose is Installed
The sweep hose operates in a gentle sweeping motion to
clean debris from hard to reach corners of pools.
Note: 1. Do not adjust the sweep hose regulator while
cleaner is operational. This may damage cleaner.
2. The sweep hose must be used to adjust the
sweep hose regulator.
1. If you do not plan on using the optional sweep hose, there
is nothing more you need to do. To attach the optional
sweep hose to the cleaner and open the sweep hose
regulator, proceed to Step 2.
2. To attach the sweep hose to the RACER™ Pressure Side
Pool Cleaner, line up the lock tabs on the inside of the
sweep hose fitting (small round fitting on the end of the
sweep hose) to the locking slots on the cleaner’s sweep
hose regulator. See figure 17.
3. The sweep hose regulator comes from the factory in the
closed position. To open the sweep hose regulator, push
the sweep hose fitting onto the sweep hose regulator.
When it can not be pushed any further turn the sweep
hose fitting clockwise until it stops (about 45 degrees).
See figure 18. Pull out on the sweep hose fitting and
the fitting will lock into place.
4. To remove the sweep hose and turn off the sweep
hose regulator, hold the sweep hose fitting and turn it
counter-clockwise until it stops (about 45 degrees). See
figure 18. Pull the sweep hose fitting from the sweep
hose regulator and store it in a safe place.
Sweep Hose
Regulator
Sweep Hose
ENGLISH
Sweep Hose
Fitting
ESPAÑOL 20
Lock Tab
FRANÇAIS 43
To Open
To Close
Figure 18.
Closed
Position
Open
Position
Sweep Hose Fitting
Locking
Slot
Sweep Hose Regulator
Figure 17.
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
10
MAINTENANCE
Periodic Maintenance
Periodically inspect the RACER™ Pressure Side Pool
Cleaner and its components. Replace and/or repair any
worn or damaged components. Failure to follow instructions
or improper installation of the cleaner can result in damage
to the cleaner, pool finish, or vinyl liner.
The following parts are wear items that should be inspected
periodically and replaced as needed.
Wall Fitting Screen
Inside the wall fitting is a stainless steel filter screen that
acts as a secondary filter. This screen captures debris
that may have passed through the pool filter.
A dirty screen may be an indication of potential
issues in your pool filter system and you may need to
contact your local pool professional.
Note: Running the cleaner without the filter screen can
damage the cleaner and void the warranty.
To clean the filter screen:
1. Switch the booster pump and then the filtration pump off.
2. Remove the wall fitting from the wall adaptor.
3. Pull the screen out from inside the wall fitting.
4. Rinse thoroughly until clean and insert back inside the
wall fitting.
5. Whenever cleaning, backwashing or repairing the pool
filter, also clean the wall fitting screen after your first
cleaner cycle.
Tires
The tires are designed to protect the bottom of your
pool and provide traction. Tires will wear and need to be
replaced occasionally.
Debris Bags
The cleaner comes with a general purpose bag and is
used for all debris types. Replace bag when the fabric is
torn or punctured.
Note: To prolong the life of your cleaner, remove it
from pool before adding chemicals.
Sweep Hose
The sweep hose is provided as an optional accessory
to help keep hard to reach corners of your pool clean.
Replace sweep hose scrubber as necessary if used.
Sweep Hose Roller Rings
Your sweep hose has a series of roller rings to protect
the sweep hose. Replace the rings as needed. Ensure
the roller rings rotate freely.
Backwashing the Pool Filter
Always disconnect the cleaner from the pool wall before
cleaning or backwashing the pool filter. After cleaning or
backwashing, let the pool filtration system and booster
pump run for a minimum of five minutes to flush out the
return lines before reconnecting the cleaner.
Feed Hose
Mender Nut
Hose Connector
Wall Fitting
Filter Screen
Figure 19.
Cleaning the Filter Screen
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
Storage and Winterizing
You may leave the wall adapter in the wall and
store the hoses straight, without any kinks. If storing
the hose coiled, be sure to lay the hose straight in the
sun for 12 to 24 hours before using again. Use the
flow gauge to be sure the flow is sufficient for cleaner
operation.
11
ENGLISH
ESPAÑOL 20
[Blank Page]
FRANÇAIS 43
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
12
REPLACEMENT PARTS
RACER™ Pressure Side Pool Cleaner Illustrated Parts List
1
28
29
28
34
19
9
10
33
31
25
18
6
30
27
15
14
32
2
2
24
27
29
29
16
41
2
27
20
6
27
8
4
5
11
KREEPY KRAULY® RACER
22
™
Pressure Side Pool Cleaner Installation and User’s Guide
37
7
27
3
21
26
38
36
39
2342
40
13
RACER™ Pressure Side Pool Cleaner Parts List
ITEM
NO.
PART
NUMBER
DESCRIPTION
1 360229 Top Front Cover Kit
2 360230 Rear Cover Kit
3 360231 Bottom Cover Kit
4 36023 Chassis Kit
5 360233 Front Grill Kit
6 360234 Side Covers Kit
7 360235 Large Wheel Kit
8 360236 Small Wheel Kit
9 360237 Large Tires Kit
10 360238 Scrubber Gear Kit
11 360239 Scrubber Kit
12* 360240
Debris Bag Kit (w/o collar), hook
and loop fastener
13* 360241 Debris Bag Collar Kit
14 360242 Vacuum Tube Kit
15 360243 Debris Valve Kit
16 360244 Sweep Hose Kit
17 360245 Sweep Hose Scrubber Kit
18 360246 Gear Box Kit
19 360247 Timer Valve Kit
20 360248 LED Kit
21 360249 Feedline Swivel Kit
22 360250 Feedline Quick Connector Kit
Note: (*) Not shown
ITEM
NO.
PART
NUMBER
DESCRIPTION
23 260251 Feedline Wall Connector Kit
24 360252 Feed Line Connector Kit
25 360253 Drive Shaft Kit
26 360254 Wheel Screw Kit
27 360255 Screw Kit
28 360256 Turn Jet Hose Kit
29 360257 Rear Thrust Jet Hose Kit
30 360258 Rubber Button Kit
31 360259 Turbine Kit
32 360260 Venturi Manifold Kit
33 360261 Water Management Kit
34 360262 Turbine Hose Kit
35* 360263 Tune Up Kit
36 360264 Feed Line Hose Kit Complete
37 360265 Soft Feed Line Hose Kit 10’
38 360266 Hard Feed Line Hose Kit 10’
39 E24 Debris Screen
40 LL23PM Threaded Wall Adapter
41 EB10G Sweep Hose Wear Ring
42 360270 Feed Line Float
43* 360268 Feed Line O-Ring Kit
44* 360269 Debris Bag with Mechanical Lock
45* 360274 Wheel Hump Insert Kit
ENGLISH
ESPAÑOL 20
FRANÇAIS 43
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
14
TROUBLESHOOTING
Use the following troubleshooting information to solve potential issues with the RACER
Problem Corrective Action
™
Pressure Side Pool Cleaner.
Cleaner doesn’t move or moves slowly.
Cleaner hangs at steps.
Cleaner tilts to one side.
Cleaner does not go in reverse.
Cleaner
will not climb.
Ensure filter pump and booster pump are on and moving water. (You may need to
clean your pool filter system.)
Ensure the wall fitting screen is free of debris; you may need to remove and rinse.
Check for proper flow using Flow Gauge (provided). See page 2. Adjust the flow at
the wall fitting if needed. See page 2.
Check all feed hose connections and swivels for leaks.
Check for debris that may be jammed in the gear teeth on one of the front drive
wheels. Gently rotate the front wheels backward to dislodge debris.
Check to see if the rear wheels are spinning freely. Replace wheels if necessary.
Ensure the front (large) wheels reverse approximately every 2-1/2 minutes.
Usually indicates a full debris bag. Empty the debris bag (see page 8).
Note: Cleaner at times will tilt on one side (on two wheels) during a turn
cycle. Watch the cleaner for a few minutes to see if it positions itself upright.
Ensure the front (large) wheels reverse approximately every 2-1/2 minutes.
Check for proper flow using Flow Gauge (provided). See page 2. Adjust the flow at
the wall fitting if needed. See page 2.
Check debris bag. Empty the debris bag if full.
Check for proper flow using Flow Gauge (provided). See page 2. Adjust the flow at
the wall fitting if needed. See page 2.
Reposition the thrust jet to increase climbing (see page 7).
Note: The climbing ability of the cleaner depends on pool shape and available
water flow. It will climb better in pools without sharp angles or in the
transition from the pool floor to the pool wall.
Hoses tangling in loops.
Sweep hose caught in vacuum tube.
Booster pump very noisy.
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
Check the length of the feed hose. If it is too long it may cause the hose to tangle or
loop. See page 4 for sizing feed hose.
Ensure the feed hose is floating on the pool surface. Hose floats should be spaced
approximately two feet apart. See page 4 for hose float positioning.
Ensure the hose swivels spin freely. Replace swivels if tight.
Ensure the feed hose has no kinks or bends.
Ensure the sweep hose regulator valve is fully open. See page 9.
Ensure filter pump and booster pump are on and moving water. (You may need to
clean your pool filter system.)
Ensure wall fitting is properly installed. If leaking, O-ring may need to be replaced.
Contact your local pool professional - possible booster pump issue.
15
Problem Corrective Action
TROUBLESHOOTING (Continued)
Brush on front of cleaner is not spinning.
Rear wheels dragging/not spinning.
Rear wheels falling off.
Night Cruize LEDs are not illuminated during
cleaner operation. (Note: LED operation does
not affect cleaner performance.)
Watch front wheels while cleaner is operating in the pool. The wheels and front
brush should rotate simultaneously.
Ensure the scrubber is free of tangled debris.
Ensure the wheel sleeve is free of tangled debris.
Note: You may need to remove the wheel by pulling straight off sleeve to
remove any tangled debris.
Replace wheel and wheel sleeve.
Debris may be clogging generator turbine. To clean debris from generator turbine:
Find access hole under the left rear wheel by removing the wheel by pulling it
straight off cleaner. Use a large paper clip and insert approximately 2in. straight into
the access hole, continue until the generator turbine paddle is felt and move paper
clip until paddle rotates. Rotate the paddle several times with paper clip to clear the
debris.
Insert paper clip in
access hole.
ENGLISH
ESPAÑOL 20
FRANÇAIS 43
KREEPY KRAULY® RACER
™
Pressure Side Pool Cleaner Installation and User’s Guide
16
TROUBLESHOOTING (Continued)
Steep Vinyl Liner Transitions
In some pools with deep diving ends the transition angle from the deep end to the shallow end may cause the
RACER™ Pressure Side Pool Cleaner to have difficulty transitioning over this angle. If so, you may need to insert
the tire wedges provided to help the cleaner make this transition. These wedges create a hump in the tire and help
keep the cleaner from becoming obstructed. They are not required in all pools.
Note: Both wedges should be installed horizontally in line with each other. If they are not in line with each other
they may cause the cleaner to have difficulty with the transition angle. This is important for proper cleaner
operation. See figure 20.
1. To install the tire wedge, pull the rubber tire up from the plastic wheel and firmly push the insert between the
tire and wheel. The smooth surface on the underside of the wedge should be inserted first, from the outside to
the inside of the cleaner wheels. See figure 21. Be sure that the slots on the plastic wheel and the slots on the
underside of the wedge lock into each other.
2. Push the wedge towards the nose of the cleaner body until the insert is securely seated behind the lip of the
rubber tire. See figure 20.
Tire Wedge
Figure 20.
™
RACER
Pressure Side Pool Cleaner Installation and User’s Guide
Figure 21.
Loading...