How it Works
Pentair
Loading...
freshpoint F1000-DFB

Pentair freshpoint F1000-DFB, freshpoint F1000-B1B, freshpoint F2000-B2B, freshpoint F2000-B2M, freshpoint F3000-B2B Installation And Operating Instructions Manual

...
Download
F1000-DFB, F1000-B1B FILTRATION SYSTEM
INSTALLATION AND OPERATION MANUAL
waterpurification.pentair.com
FreshPoint F1000-DFB, F1000-B1B Filtration System
INSTALLATION INSTRUCTIONS
English .................................Pages 3-9
FreshPoint F1000-DFB, F1000-B1B Sistema de filtración
INSTRUCCIONES DE INSTALACIÓN
Español ............................. Páginas 11-16
FreshPoint F1000-DFB, F1000-B1B Système de filtration
DIRECTIVES D'INSTALLATION
Français .............................. Pages 17-23
2 • FRESHPOINT F1000-DFB, F1000-B1B Filtration Systems Instruction Manual
WARNING:
SPECIFICATIONS
WARNING:
CAUTION
Service Flow Rate @ 60 psi (4.1 bar):
Rated Service Life:
Model: F1000-DFB .......................................750 gallons (2,839 L)
Model: F1000-B1B .......................................750 gallons (2,839 L)
(311mm x 90mm x 122mm) Weight:
Model: F1000-DFB (system only).........................1.6 lbs (0.72 kg)
Model: F1000-B1B (system only) .........................1.8 lbs (0.81 kg)
PARTS INCLUDED
• Filter System with Cartridge
• Installation Hardware Kit
• Lead-free drinking water faucet
• 3/8" (white and blue) plastic tubing
PRECAUTIONS
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. Chemical and mechanical reduction unit.
TOOLS AND MATERIALS REQUIRED
• Safety glasses
• Adjustable wrench
• Tube cutter or utility knife
• Hand or electric drill (cordless recommended)
• File
• 1/4" drill bit
If sink does not have hole for separate faucet:
• Center punch
• 3/4" drill bit or hole saw
• 3/32" drill bit
System must be protected against freezing, which
can cause cracking of the filter and water leakage.
NOTE:
• For cold water use only.
• Make certain that installation complies with all state and local laws and regulations.
• The system must be maintained according to manufacturer’s recommendations, including replacement of filter cartridges. The contaminants or other substances removed or reduced by the selected cartridge are not necessarily in your water. Ask your local water municipality for a copy of their water analysis, or have your water tested by a reputable water testing lab.
• After prolonged periods of non-use (such as during a vacation) it is recommended that the system be flushed thoroughly. Let water run for 5–6 minutes before using.
• The filter cartridges used with this system have a limited service life. Changes in taste, odor, and/or flow of the water being filtered indicate the cartridge should be replaced.
CALIFORNIA PROPOSITION 65 WARNING
This product contains chemicals known to the
State of California to cause cancer or birth defects or other reproductive harm.
FRESHPOINT F1000-DFB, F1000-B1B Filtration Systems Instruction Manual • 3
INSTALLATION
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
NOTE:
• For standard under-sink installation on 1/2" 14 NPS threads or 3/8" x 3/8" compression
• Please read all instructions and precautions before installing and using your Filtration System
• Numbered diagrams correspond with numbered steps
1. Installing the Water Supply Adapter
The supply adapter fits 1/2"-14 NPS supply threads or 3/8" x 3/8" compression. If local codes permit, it may be used to connect the system to the cold water supply line. If local codes do not permit the use of the supply adapter, alternate connectors can be obtained from your local supplier.
A. Turn off cold water supply line. If cold water line does not
have a shut-off valve under the sink, you should install one.
B. Turn on the cold water faucet and allow all water to drain
from line. C. Disconnect riser cold water supply valve. D. Ensure the sealing gasket is fully seated into the feed
adapter valve female thread. E. Install feed adapter valve onto supply valve. Hand tighten
only. F. Connect the riser to the feed adapter valve.
NOTE: See Figures 1G-1H for configuring the feed adapter to
3/8" x 3/8" compression connections.
2. Selecting the Faucet Location NOTE: The drinking water faucet should be positioned with
function, convenience, and appearance in mind. An adequate flat area is required to allow faucet base to rest securely. The faucet fits through a 3/4" hole. Most sinks have pre-drilled 1-3⁄8" or 1-1⁄2" diameter holes that may be used for faucet installation. If these pre­drilled holes cannot be used or are in an inconvenient location, it will be necessary to drill a 3/4" hole in the sink to accommodate the faucet.
This procedure may generate dust which can cause
severe irritation if inhaled or come in contact with the eyes. The use of safety glasses and respirator for this procedure is recommended.
DO NOT ATTEMPT TO DRILL THROUGH AN ALL-
PORCELAIN SINK. If you have an all-porcelain sink, mount the faucet in pre-drilled sprayer hole or drill through countertop next to sink.
When drilling through a countertop, make sure the
area below the drilled area is free of wiring and piping. Make certain you have ample room to make the proper connections to the bottom of the faucet.
Do not drill through a countertop that is more than
1" thick.
Do not attempt to drill through a tiled, marble,
granite or similar countertop. Consult a plumber or the countertop manufacturer for advice or assistance.
A. Line bottom of sink with newspaper to prevent metal
shavings, parts, or tools from falling down the drain. B. Place masking tape over the area to be drilled to prevent
scratches if drill bit slips. C. Mark hole with center punch. Use a 1/4" drill bit to drill
pilot hole. D. Use a 3/4" drill bit and drill a hole completely through sink. E. Smooth rough edges with a file.
1C
1G
2
1B
1A
1D
Sealing Gasket
1H
C
1
4”
D
11⁄4”
⁄
4 • FRESHPOINT F1000-DFB, F1000-B1B Filtration Systems Instruction Manual
WARNING:
INSTALLATION CONTINUED
3. Mounting the Faucet
A. Apply 3-5 wraps of plumber tape to faucet stem. B. Assemble faucet as shown in (Figure 3). C. Screw quick connector onto threaded end of faucet stem. D. Place a mark 5/8" from one end of the blue tubing. Wet the
end of the 3/8" tube and push into bottom of connector. The 5/8" mark should be flush with the collar of the connector.
NOTE: To remove the tube, push on the fittings' collar and pull
the tube out.
E. Holding the faucet, feed the tubing through the hole in the
sink. Position the faucet handle at a desired location.
F. Center the faucet and slip slotted disc between the bottom
of the counter or sink and lock washer. Tighten the stem nut with a wrench until it is tight.
G. Firmly insert spout into faucet base.
4. Mounting the System
A. Select a location under the sink, or other suitable area
where the system will be installed.
NOTE: The system carton can be used to determine the
operational footprint required for installation of the system and replacement cartridges. (Figure 4a)
B. Mount the system vertically. Dimensions in the diagram
allow for cartridge or system removal. Ensure mounting is level. Use the 3/32" drill bit to create pilot holes for the mounting (Figure 4b).
3
Faucet Stem
Chrome Plate
Rubber Washer
Slotted Disk
Lock Washer
Stem Nut
Quick Connector
3/8” Tubing
Count er Top
The system should be mounted to a firm, solid
surface that is able to support the weight of the system.
4b
2 3/8” (60.3 mm)
4a
7” (178 mm)
Inlet
Outlet
13.5” (343 mm)
7.875” (200 mm)
FRESHPOINT F1000-DFB, F1000-B1B Filtration Systems Instruction Manual • 5
CAUTION
INSTALLATION CONTINUED
5. Connecting the Faucet to the System
A. Determine the length of plastic blue tubing needed to
connect to the outlet (right) side of the filter from the
faucet. Be sure to allow enough tubing to prevent kinking
and cut the tubing squarely. Use a marker to mark one end
of the tubing 5/8" from the end (Figure 5). Wet the end of
the 3/8" tube and push into the outlet (right) connection of
the system up to the mark.
Do not bend or crimp tube inserting.
B. Gently pull back on the tube to ensure it is connected
properly.
6. Connecting the Supply Adapter
A. Determine the length of plastic white tubing needed
to connect the inlet (left) side of the filter with the feed
adapter installed on the cold water supply line. Be sure to
allow enough tubing to prevent kinking and cut the tubing
squarely. Place a mark 5/8" from one end of the tubing. Wet
the end of the tubing. Insert the end of the tubing into the
3/8" fitting of the inlet supply adapter. The 5/8" mark should
be flush with the collar of the fitting located on the inlet
supply adapter (Figure 6a). B. Mark the remaining end of the tubing. Use a marker to
mark 5/8" from the end. Wet the end of the tube. Insert the
end into the feed connection on the inlet side (left) of the
system. The tube should go in up to the mark. (Figure 6b).
7. Placing the System into Operation
A. Slowly turn on the cold water supply. Ensure that the feed
adapter valve is also open. B. Open faucet and flush filter for 10 minutes. Discard water. C. Check for leaks at all fittings before leaving installation. If leaks
appear, see Troubleshooting.
NOTE: A drinking water cartridge may contain carbon fines
(very fine black powder). If carbon fines appear in the water, discard water. More flushing is required if carbon fines are present.
NOTE: Initially, filtered water may appear cloudy. If
cloudiness in a glass of water disappears from the bottom; fine air bubbles are present. This air within the water will disappear within a few weeks after installation.
5
6b
7
6a
Closed to system
6 • FRESHPOINT F1000-DFB, F1000-B1B Filtration Systems Instruction Manual
Open to system
Inlet
(white tubing)
Outlet (blue tubing)
INSTALLATION IS NOW COMPLETE.
FILTER CARTRIDGE REPLACEMENT
NOTE: The life of the filter cartridges depends on water
volume used and the quality of the feed water. It is recommended that the filter cartridges be replaced every 6-12 months, or when there is a noticeable change in taste, odor, or flow of filtered water.
Ensure the correct cartridge is purchased for the system.
Model F1000-DFB uses FDF1-RC Replacement Cartridge Model F1000-B1B uses F1B1-RC Replacement Cartridge
8. Cartridge Replacement
A. Relieve pressure by turning off the water supply to the
system and opening a faucet until water flow stops. Place a bucket or towel under the system to catch any water drips (Figure 8a).
B. Lift the locking bar upward until the filter cartridge
disengages from the filter head assembly (Figure 8b).
C. Pull the cartridge away from the filter head assembly and
ensure the locking bar remains in the fully up position (Figure 8c).
D. Align the posts on the filter cartridge with the ports in the
filter head assembly. Slide the cartridge filter towards into the filter head assembly engaging with the locking bar causing it to drop forward and down. (Figure 8d).
E. Pull down the locking bar until it snaps into place
(Figure 8e).
NOTE: See Placing the System into Operation section for
remaining steps.
8a
8b
or
8c
TROUBLESHOOTING
Leaks between filter head assembly and filter cartridge
1. Relieve pressure by turning off the water supply to the system and opening faucet until water flow stops. Place a bucket or towel under the system to catch any water drips.
2. Remove cartridge and inspect O-rings to make sure they are seated and clean.
3. Install filter cartridge. Place system into operation and check for leaks. If leaks persist, turn off the water supply and contact Technical Support at 1-800-279-9404.
Leaks from tubing fittings
1. Relieve pressure by turning off the water supply to the system and opening faucet until water flow stops. Place a bucket or towel under the system to catch any water drips.
2. Depress collet on system or inlet supply adapter tubing fittings and pull tubing from fitting. Inspect surface of tubing for scratches or debris. Clean or cut back tubing to access clean surface.
3. Wet the end of the inlet tubing and press into the inlet fitting of the system. Ensure the tubing is fully pushed past the fitting O-rings. Place system into operation and check for leaks. If leaks persist, turn off the water supply and contact Technical Support at 1-800-279-9404.
8d
8e
FRESHPOINT F1000-DFB, F1000-B1B Filtration Systems Instruction Manual • 7
REPLACEMENT PARTS
ITEM
NUMBER
1
2
3 4004294 Installation Kit 1 4 244960* Faucet 1
*Image may be different than actual faucet
PART
NUMBER 655123-96 Cartridge, FDF1-RC 1 655120-96 Cartridge, F1B1-RC 1
4004601 Filter Head, Model F1000-DFB 1
4004602 Filter Head, Model F1000-BIB 1
DESCRIPTION
2
QUANTITY REQUIRED
3
4
1
For replacement parts, contact your nearest Pentair distributor or call
800.279.9404
8 • FRESHPOINT F1000-DFB, F1000-B1B Filtration Systems Instruction Manual
Loading...
+ 16 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use