Deck Jet Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
READ & FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CAUTION
Before installing this product, read and follow all warning notices and instructions accompanying this product. If you have application questions
or would like additional copies of these instructions, please call (800) 831-7133.
Important Notice
Attention Installer.
This manual contains important information about the installation, operation and safe use of this product. This information should
be given to the owner/operator of this equipment.
Thank you for your purchase of the Pentair Deck Jet. This innovative water effect is designed to be cast into the
concrete deck or gunite sidewall of a swimming pool. It can also be mounted through the sidewall of a vinyl liner in-ground
or above ground pool. It is furnished with five water effect eyeballs, one of which you will install in the body after the pool
is complete.
It is recommended that you supply the Deck Jet with filtered water. Also, if more than one Deck Jet is used on this pool,
we recommend that a PVC ball valve be used to control the flow to EACH effect. This is because the flow and pressure
requirements are so low that any difference in water pressure caused by piping length will be noticed.
The supply piping to the Deck Jet can be any size (1/2" recommended). The connection on the bottom of the body
is 1½" slip.
If the Pentair Deck Jet is to be mounted into concrete or gunite:
1. Place the plastic parts bag in a safe location. This contains all the
parts you will need to activate the water effects after the pool
hardscape is complete.
2. Leave the red gunite shield pressed securely in the body to prevent
contamination of the internal threads.
3. You will need to adapt your supply piping to the 1½ " PVC slip
connection with a reducing bushing. Glue the bushing to the body.
4. Glue the supply piping to the bushing.
5. Secure the body to prevent movement during the gunite/concrete
placement. You can drill holes in the horizontal flange and wire the
body to the rebar. Because the Deck Jet is round, you can orient it
in any direction.
6. The top flange of the shield plug should be flush with the FINAL
prepared surface.
(continued on the back side)
Red Gunite
Shield
Body
Bushing
Supply
Piping
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400
Rev. A 6-7-05 1 P/N 590009
If the Pentair Deck Jet is to be mounted into the sidewall of a vinyl lined pool:
1. Place the plastic parts bag in a safe location. This contains all the
parts you will need to activate the water effects after the pool
hardscape is complete.
Pool Sidewall
2. Cut a 2-3/8" diameter hole, above water level, at the location desired.
3. Put a gasket on the body and insert the body through the hole from
the outside.
4. Put on the remaining gasket, friction ring, and nut. Tighten the nut
until the gasket is compressed slightly. All threads on the nut should
be engaged, but it is recommended that the body not stick out of the
nut too far. If desired, a bead of silicone caulking can be applied to
better seal the pool wall.
5. You will need to adapt your supply piping to the 1½ " PVC slip
connection with a reducing bushing (1/2" piping is recommended).
6. Glue the supply piping to the bushing.
7. Support the piping on the outside of pool to prevent potential pipe
breakage.
Replacement Parts
Item
No. P/N Description
Body
Capture Ring
Friction Ring
Gasket
Nut
1 87200800 Fitting Nut ,Sealing Liner 2"
2 87200700 Friction Ring, SIF
3 87201200 Gasket TH-AGF 3.5" OD x 2-3/8" ID
4 590005 Plug, Gunite Shield, L20
5 590010 Eyeball Kit
includes: Installation Card
6 590011 Accessory Kit
includes: Capture Ring – (2 qty.)
O-ring – (3 qty.)
Filter Pad – (2 qty.)
Silicone Lubricant – (1 qty.)
SAVE THESE INSTRUCTIONS.
© 2005 Pentair Water Pool and Spa, Inc. All rights reserved.
This document is subject to change without notice.
1
5
2
3
O-ring
4
Filter Pad
Body Body
6
Silicone
Lubricant
Trademarks and Disclaimers. The Pentair Water Pool and Spa logo is a trademark of Pentair Water Pool and Spa, Inc. Other trademarks and trade
names may be used in this document to refer to either the entities claiming the marks and names or their products. Pentair Water Pool and Spa, Inc.
disclaims any proprietary interest in trademarks and trade names other than its own.
P/N 590009 2 Rev. A 6-7-05