Pentair CSP Series User Manual

CSP Series
Commercial Self-Priming Pump
For commercial and public swimming pools and spas, aquatic facilities, water parks and fountain applications where high performance and self-priming characteristics are desired.
Rugged, self-priming CSP Series™commercial pumps feature an enclosed bronze impeller, standard 6" x 4" flange connections, plus a 1,100 cubic inch capacity hair and lint strainer. Motors are standard JM type, NEMA “C” flange design with a stainless steel shaft sleeve. These
1
cast iron pumps are available in 7
2, 10, 15 and 20 HP, and may be purchased with or without corrosion-preventing epoxy coating on all wetted surfaces. Pump and strainer sold separately.
Pentair Water Commercial Pool and Spa
Standard Features
Cast iron construction, enclosed bronze impeller and
bronze wear rings for long lasting reliability
Exceptional self priming design with hair and lint
strainer installed – allows pumps to be installed above or below water level.
Oversized hair and lint strainer* with electro-polished
stainless steel basket holds a large quantity of debris.
Available in a wide range of performance levels from
1
7
2 to 20 HP to handle your varied pumping needs.
®
Nationally recognized NEMA
performance under continuous operation.
Back pull-out design enables servicing of normal
wearing parts without disconnecting piping.
Dimensionally compatible to most installations for
easier initial hook-ups or retrofits.
Integral design base is slotted for ease of mounting.
To insure priming and proper pump operation, install only with Sta-Rite Hair
*
and Lint Strainer
. Order pump and strainer separately.
motors offer high
.
CSP Series
FLOW RATE IN GPM
0
25
50
75
100
125
150
100 200 300 400 500 600 700 800 900
BEST EFFICIENCY SIZING
TOTAL DYNAMIC HEAD IN FEET OF WATER
A
B
C
D
TOTAL DYNAMIC HEAD IN FEET OF WATER
FLOW RATE IN GPM
0
25
50
75
100
125
150
100 200 300 400 500 600 700 800 900
BEST EFFICIENCY SIZING
A
B
C
D
Commercial Self-Priming Pump
KEY – TRAP INSTALLED
A. CSPHK/CSPH
B. CSPHL/CSPHL3
C. CSPHM3
D. CSPHN
KEY– WITHOUT TRAP
A. CCSPHK/CCSPHK3
B. CCSPHL/CCSPHL3
C. CCSPHM3
D. CCSPHN
Performance Curves with Trap Installed
For detailed efficiency curves for each model, please contact the factory.
MATERIALS AND DESIGN
Pump Body
Volute type, back pull-out design
Performance Curves without Trap
Pump Maximum Limits
Liquid Temperature: 125ºF Ambient Air Temperature: 104ºF pH Range: 6.0-9.0
Port Size
4" – ANSI 125 bolted flange discharge port. 6" – ANSI 125 bolted flange suction port.
Material – Volute and Motor Adapter
Cast iron.
Impeller
Bronze enclosed design with bronze wear ring.
Base
Cast iron integral design, slotted for mounting ease.
Corrosion Prevention
“CC” models have Fusion Bonded Epoxy coating of Scotchkote®134 on all wetted cast iron surfaces for maximum hydraulic performance and corrosion prevention.
Hair and Lint Strainer
Material
Separate bolt-on cast iron body and cover; stainless steel toggle bolts. Ductile iron wing nuts; perforated electro-polished stainless steel basket.
Size
6" ANSI 125 bolted flange suction and discharge ports.
Motor
Standard “JM” type
Frame Size
NEMA “C” flange. 230/460V are open drip-proof design. 200V are totally enclosed, fan cooled.
Shaft
Stainless steel sleeved, and gasketed construction.
Design
71⁄2 to 20 HP continuous duty, three phase and single phase (71⁄2 HP, 10 HP only).
Bearings
Sealed ball type, permanently lubricated.
Thermal Overload Protection
All models require external thermal overload protector
, 3500 RPM, JM open drip-proof,
Electrical
Power Supply Requir
Three-phase pumps are dual voltage. 71⁄2 and 10 HP single-phase models are available in 230V, 60 Hz only
.
ed
.
CSP Commercial Pump
SECTION B - B
2
(VOLUTE TOP VIEW)
3
9.00
1
4", 125 LB. ANSI DISCHARGE FLANGE
5
/8 - 11 UNC x 1.28 DEEP
1
(8) PLACES.
(
6.00
11.00
9.50 BC
.88 THRU (8) PLACES
22.5°
6.88
8.50
10.45
4
.25
5.225
7.92
4.06
1
5.85
SLOTS FOR 5/8" MOUNTING BOLTS
B
A
T
E
FLOW
1
6.38
20.27
11.00
3.44
19.48
1/4 NPT PLUG
(OPTIONAL PRESSURE
GAUGE LOCATION)
1/2 NPT
DRAIN PLUG
F
R
D
6.25
S
C
P
B
B
7.68
11.62
1/4 NPT
PLUG
(OPTIONAL
SUCTION
GAUGE
L
OCATION)
3/4 - 10 UNC THRU FLANGE
6",
1
25 LB.
ANSI
SUCTION
FLANGE
1
D
RAIN P
LUG
1/2 NPT
S
(6) PLACES
3/4 - 10 UNC
x 1.60 DEEP
16.55
19.30
2
0.32
B
Outline Dimensions
All dimensions shown in inches.
Catalog Number A B CP D E F G H I
CSPHK, CCSPHK 10.62 7.00 39.44 5.25 4.25 5.50 1.00 30.00 8.50 CSPHK3, CCSPHK3, CSPH2K3 9.00 6.75 40.31 4.50 3.75 5.50 1.75 29.13 7.50 CSPHL, CCSPHL 10.35 8.26 42.69 5.25 4.25 7.00 1.00 30.00 8.50 CSPHL3, CCSPHL3 10.62 7.00 41.00 5.25 4.25 5.50 1.00 30.00 8.50 CSPHM3, CCSPHM3 10.62 8.50 42.50 5.25 4.25 7.00 1.00 30.00 8.50 CSPH2L3, CSPH2M3 10.62 8.50 42.50 5.25 4.25 7.00 1.00 30.00 8.50 CSPHN3, CCSPHN3 12.50 10.80 46.75 6.25 5.00 8.20 0.00 31.62 10.00 CSPH2N3, CCSPH2N3 13.38 12.44 48.50 6.25 5.00 10.00 0.00 31.65 10.00
Ordering Information
Catalog Nominal Motor Full-Load* Approx. Ship. Weight lbs. (kg) Number HP (kw) Phase Voltage Amps (Pump Only)
CSPHK/CCSPHK
CSPHK3/CCSPHK3 7-1/2 (5.6) 3 208-230/460 21.7/18.0/9.8 265 (120)
7-1/2 (5.6)
1 230 39 270 (122)
CSPH2K3/CCSPH2K3 7-1/2 (5.6) 3 200 22.1 265 (120)
CSPHL/CCSPHL
CSPHL3/CCSPHL3
10 (7.5) 1 230 46 275 (124)
10 (7.5) 3 208-230/460 27.6/25/12.5 270 (122)
CSPH2L3/CCSPH2L3 10 (7.5) 3 200 28.1 270 (122)
CSPHM3/CCSPHM3 15 (11.2) 3 208-230/460 44.2/40/20 280 (127)
CSPH2M3/CCSPH2M3
15 (11.2)
3
200
42.3 280 (127)
CSPHN3/CCSPHN3 20 (15) 3 208-230/460 55.3/50/25 325 (148)
CSPH2N3/CCSPH2N3
20 (15)
*Amp draw may vary depending on motor manufacturer
OPTIONS:
CCSP Models feature special epoxy coated castings for maximum performance and corrosion resistance. 60 Hz T.E.F.C., 60 Hz premium efficiency, or 575 volt motors available, consult factory.
3
.
NOTE: Maximum ambient temperature for motor is 104°F (40°C). All pump motors require external overload protection (magnetic starter).
Pump strainer must be ordered separately (see below). Full load amps on motor model plate.
200 57.3 350 (159)
Accessory Ordering Information
Catalog Approx. Ship Approx. Ship. Number Description
PKG 184 Strainer for CSP/CCSP, 6" ANSI Flange (1,100 cu. in. capacity) 180 (82) 6.4 (.18)
PKG 184C Strainer for CSP/CCSP, 6" ANSI Flange (1,100 cu. in. capacity), Epoxy Coated 180 (82) 6.4 (.18)
Weight lbs. (kg) Vol. Ft
3(m3
)
PKG 184
CSP Series
Commercial Self-Priming Pump
ENGINEERING SPECIFICATIONS
CSP/CCSP Series Pump
Recirculating pump shall be Sta-Rite Model No. _________
self-priming centrifugal pump, ____ phase, 60 Hz.
General Notes
Install pump in a cool, dry, well vented location away from pool
heaters, and chemical storage.
Pump should be firmly mounted with pipe supported, to prevent
vibration and undue operational noise.
Allow 12" minimum clearance behind motor for servicing.
Motor overheating may be caused by a voltage drop or excessive
voltage. Be sure that wire size and voltage input is properly regulated.
Specifications
The recirculating pump shall be a self-priming, centrifugal design
with a hair and lint strainer as shown in the plans.
The pump body, seal plate, and attached hair and lint strainer shall
be constructed of close-grained gray iron with fusion-bonded epoxy coating of Scotchkote®134 on all wetted cast iron surfaces and close-coupled to an electric motor by means of an adaptor of the same material. The pump body shall have a single suction port with a 6” ANSI®125 bolt flange to the hair and lint strainer discharge port of 4” ANSI®125 bolt flange and a winterizing drain port of 1⁄4” NPT shall be a part of the design.
The pump shall be a back pull-out design to allow servicing with-
out disturbing piping. The pump shall have a cast iron diffuser to aid in priming and it shall contain a replaceable bronze wear ring for the impeller. The impeller shall be of the closed type and cast in red brass, non-overloading at any point on the performance curve. The mechanical shaft seal shall be a John Crane®type 21 or equivalent and constructed of ceramic and carbon seal faces, with stainless steel, brass and Buna N materials in the spring bellows portion. The impeller shall be secured to the motor shaft by means of a stainless steel key and locking screw into the end of the motor shaft. There shall be a shaft slinger made of
. A centerline
neoprene to protect motor bearings from any seal leakage. The pump shall be capable of operating at up to 75 psi, 125°F continuous water temperature and within a pH range of 6 to 9.
The electric motor coupled to the pump shall be of the NEMA
series JM construction with carbon steel shaft inside a remov­able shaft sleeve of 300 series stainless steel. The motor shall be of an open drip-proof design (unless otherwise specified) with permanently sealed ball bearings. Motors shall be continuous duty rated at 40°C (or better) ambient and be suitable for outdoor installation.
The pump motor shall be a ___ HP, ___ phase, 60 Hz, 3450 RPM
for service on a ___ volt electric supply. The pump shall be rated for ______ GPM at ____ TDH. The pump shall be tested and certified by a nationally recognized testing laboratory to conform to National Sanitation Foundation Standard 50. (CCSP models only.)
®
Hair and Lint Strainer
The pump strainer shall consist of a ______ (red brass/cast iron)
body, cover with O-ring seal, threaded locking handles, and a strainer basket of perforated electro-polished stainless steel basket material.
The strainer body shall be 6" ANSI®125 bolt flanged with fusion-
bonded epoxy coating of Scotchkote®on all wetted cast iron surfaces unless specified for in-line mounting ahead of the pump. The strainer body shall have a removable drain plug for winterizing.
The strainer basket shall be securely positioned below the
suction inlet of the trap, with access for inspection and cleaning through a removable trap body lid. The trap body lid shall be secured by means of threaded locking handles. The strainer basket shall have perforations which in total area is equal to 6 times the open area of the suction pipe into the trap body inlet.
The pump strainer shall be Sta-Rite Model No. _______
: 800-831-7133
Phone
Fax: 800-284-4151
.pentairpool.com
www
www.starite.com
1/06 Part #P1-741 ©2006 Pentair Water Pool and Spa, Inc. All rights reserved.
Loading...