PelPro Wood Pellet Stoves HHPP2, HSPP2, HSPP3, HHPP3 User Manual

“Save These Instructions”

II or III

with Memory& Fan Trim

HSPP3

HSPP2

Model

C C 1

Model

C C 2

Toll Free Technical Support

HHPP3

Model

C C 2

HHPP2

Model

C C 1

1 - 866 - 456 -926 9

To register your purchase

Installation sha ll confo rm t o CAN/ CSA B365 Installa tion Code for Solid-Fuel-Bu rni ng Appliances and

Equipment in Canada an d NFPA 211 Chimney, Fireplaces, Vents and Solid Fuel Burning Appliances in the US

Contact local building or fire officials about restrictions and installation inspection requirements in your area.

www.dansons.com/support

Dear Pellet Stove Owner:

PELPRO

CONG RATULATION S on the purchase of your You

PELPRO Multi-fuel pellet appliance!

have selected the f inest in resident ial w ood pel let heating technology. Let us pass on a few "tips" concerning installing your stove and heating with wood pellets.

1. Whet her you i nstal l your sto ve yoursel f or hi re a prof essional inst all er,

a qual ity installation is a must

for the safety of your family and for efficient, satisfactory operation of your

stove.

Initial Burn Setup of the stove

2. is the most import ant step to ensure the efficient and satisfactory operat ion of your appli ance for many ye ars to come.

Pellet Stoves ARE NO T plug ‘ n

play.

Know the quali ty and characteristics of the pellets you burn.

3. Pell et s can vary greatly from company to company, from load t o load and occasionally from bag to bag.

4. Be extra .

diligent i n your cl eaning program

5. Rem em ber t hat a very high percentage of operat ional dilem m as with a pellet st ove are

usually traced back to Imp roper insta ll ati on, poor quality pelle ts and/or a lack of t imely cleaning.

With just a minimum of daily care your PELPRO pellet appliance will provide years of clean, eff ici ent, comfortable and environmentally sound heati ng.

Thank you for selecting a PELPRO wood pell et appliance. Sincerely,

Canadian Comfort Industri es & Dansons Inc.

UPDATES and REGISTRATION

Up t o date addi ti ons, product inf orm ati on, product regist ratio n and warranty ext ension registrat ion can be found on our websit e w w w.danson s.com/support

Friendly Reminder:

A pellet stove / insert is not designed or tested as a primary source of heat. They are designed to

be a supplementary heat only. Please do not disconnect or remove your existing primary heat source.

PelPro Home & Shop Heater www.pelprostoves.com 2

ABLE

ONTENTS

GENERAL INFORMATION

AFETY PRECAUTIONS

SAFETY TESTING HOW YOUR APPLIANCE WORKS AUTOMATIC SAFETY FEATURES SPECIFICATIONS

ELECTRICAL REQUIREMENTS PRE PLANNING

PLANNING & INSTALLATION CHECKLIST PLANNING EXHAUST SYSTEMS TYPE SAFETY PRECAUTIONS DETERMING SIZE & DISTANCE TERMINATION PLANNING OUTSIDE AIR APPLIANCE PLACEMENT

FLOOR PROTECTION CLEARANCES TO COMBUSTIBLES

INSTALLATION

OOLS OF THE TRADE

TEP BY STEP DIRECT VENT INSTALLATION

S M

OBIILE HOME

NSTALLATIONS OPTIONS

PERATION

EFORE LIGHTING YOUR FIRST FIRE

SING THE ACUTRON CONTROLS

HOOSING YOUR MODE OF OPERATION

C M

U IL P

UEL

W C

ANUAL MODE

THERMOSTAT MODES (OPTIONAL)

NDERSTANDING YOUR ACUTRON CONTROL

IGHTING YOUR FIRE

ERFORMANCE ENHANCEMENT TIPS

OOD PELLETS

ORN AND OTHER BIOMASS

4 5 6 7 8

11 12 13 14

16 17 18 19

21 22 23

24 25 26 27

28 29

MAINTENANCE

REQUIRED ROUTINE CLEANING 2 TO 3 DAYS OR WEEKLY PERIODIC MAINTENACE 1 TON, SEASONAL, BI-SEASONAL FALL START-UP SPRING SHUT-DOWN

YEARLY MAINTENANCE CONTRACTS

TROUBLE SHOOTING REPLACEMENT PARTS HOPPER CLEAN-OUT CHUTE LIMITED WARRANTY SERVICE MAINTENANCE LOG

32 32

33 33

36 37 38 39

PelPro Home & Shop Heater www.pelprostoves.com 3

AFETY

RECAUTIONS

IMPORTANT:

RECOMMENED: For your and your families protection and well being, Dansons’ highly recommends

• BEFORE installing or having the pellet appliance installed contact the local building officials to obtain the necessary permits and information on any installation restrictions or inspection requirements in your area and notify your insurance company you have installed a pellet appliance.

• This unit must be properly installed to prevent the possibility of a house fire. The instructions and local building codes requirements must be strictly adhered to. Do not; use makeshift methods or material that may compromise the installation.

• When the pellet appliance is installed in a mobile home, the heater must be bolted to the floor, have outside air, and MUST NOT BE INSTALLED IN THE BEDROOM in accordance with the Manufactured Home and Safety Standard (H.U.D), CFR 3280, Part 24. Check with local building officials.

• NEVER try to repair or replace any part of the heater unless instructions for consumer are given in this manual or instructed by Dansons Customer Service Department. A trained technician should do all other work.

• Educate all children of the danger of a high-temperature heater. Young children should be supervised when they are in the same room as the heater.

Read, save and follow the instructions in this manual. It contains important safety, operating

and maintenance instructions you will need.

installing and maintaining both a smoke detector as well as a CO2 detector.

• This heater is designed and approved for pelletized wood fuel, shelled corn, or wheat only. Any other type of fuel burned in this heater will void the warranty and safety listing. Keep foreign objects out of the hopper.

• NEVER use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or “freshen up” a fire in this appliance. Keep all such liquids well away from the appliance while it is in use.

• This heater must be connected to a standard 115 V., 60 Hz 3-prong grounded electrical outlet in accordance with local building codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70. A grounded surge-protection unit is recommended.

• Do not use an adapter plug or sever the grounding prong on the electrical plug.

• Do not route the electrical cord underneath, in front of, or over the heater.

• Do not unplug the stove if you suspect a malfunction.

Push the “OFF” Touch Pad and inspect the heater.

• The heater will not operate during a power outage. If a power outage does occur, check the heater for smoke spillage and open a window if any smoke spills into the room.

• DO NOT operate the heater if you smell smoke coming from the heater. Push the “OFF” Touch Pad, monitor your pellet appliance, and call your local authorized dealer.

• Do not place clothing or other flammable items on or near the heater. When installed with a thermostat there is a possibility of the heater turning on and igniting any items placed on or near the unit.

• CAUTION: To prevent fingers, clothing or other objects from coming in contact with the auger; your appli- ance is equipped with a shutoff switch which stops the auger when the hopper lid is ope n. THE AUGER IS CAPABLE OF CAUSING SERIOUS INJURY AND THIS SWITCH MAY NOT BE DISCONNETED.

PelPro Home & Shop Heater www.pelprostoves.com 4

• DO NOT operate the stove if the flame becomes dark and sooty or if the firepot overfills with pellets. Push

the OFF Touch Pad and inspect the heater. (See Operating Your Stove). Soot or creosote may accumulate in the exhaust vent system when the stove is operated under incorrect conditions such as an extremely rich burn. The flame will have a lazy orange color with black tips. This indicates poor pellet fuel combustion.

• NEVER block free airflow through the open vents of the unit. The viewing door and ash pan must be

closed and latched during operation.

• The pellet appliance exhaust system works with negative combustion chamber pressure and a positive

chimney pressure, therefore the exhaust system must be completely airtight and properly installed. All exhaust system vent joints must be sealed, gas tight, with HI-TEMP RTV silicone sealant, and/or at least 3 sheet metal screws per joint and to the heater also.

• Your heater requires periodic maintenance and cleaning (Refer to ”Routine Cleaning” sectio n of the

manual). Failure to maintain your heater may lead to smoke spillage in your home.

• Disconnect the power cord from the electrical outlet before performing any maintenance. Pushing ”OFF”

Touch Pad does not disconnect all power to the heater.

• BEFORE carrying out any maintenance or cleaning, allow the heater to cool. Ashes must be disposed in a

metal container with a tight lid and placed on a non-combustible surface or on the ground, well away from all combustible materials, pending final disposal.

• The exhaust system should be checked twice a year minimum for any build-up of soot or

creosote. Do not touch the hot surfaces of the heater.

NOTE: Canadian Comfort Industries grants no warranty, implied or stated, for the installation or maintenance of your appliance, and assumes no responsibility of any consequential damage(s).

AFETY

In accordance with the procedures and specifications listed in UL1482 – 1998 & ASTM E 1509-04, and ULC-S627-00 and ULC-S628-M93 for solid fuel room heater, the Canadian Comfort Industries pellet stove has been independently tested and listed by INTERTEK. (an accredited testing laboratory) to UL, ULC and CSA standards. It is tested and listed for residential installation according to current national and local building codes as:

ESTING

• A Freestanding Room Heater

• A Hearth Stove

• A Mobile Home Heater.

The Safety Listing Label is located on the rear inspection panel for model CC1 and CC2. Please read the label carefully. It contains important information about installation and operation of your pellet appliance.

Note that your STOVE’S serial number is located on the safety label. Your appliance serial number is preceded by a “WH-“ (example WH-00000). (see diagram)

PelPro Home & Shop Heater www.pelprostoves.com 5

The operations and maintenance of your PelPro Series of multi-fuel appliance are unique and should not be considered to be like a wood, coal, gas, electric, propane or oil heater, stove or appliance.

OUR

PPLIANCE

ORKS

Cautions:

Do not try to operate your stove with viewing door open. Pellets will not feed under these circumstances and a safety concern may arise from sparks or fumes entering room.

If you are not drawing combustion air from outside, care must be taken to allow for adequate air make up, to avoid possible room air starvation when stove or other exhaust fans are in operation.

It is highly recommended that you install a high quality smoke detector as well as a carbon monoxide gas detector in the room where stove is installed. Care should be taken to make sure detectors are in working order at all times.

FUEL CONSIDERATIONS

Your PelPro Series of Multi-fuel appliance is designed to burn the following:

1. Wood pellets that comply with the Pellet Fuel Industries standards.

2. A combination of up to 50/50 Wood Pellet and Shelled Corn

3. 100% Shelled Corn, using the supplied corn grate, and manual start only. NO IGNITER

Fuel in the form of wood pellets, shelled corn or grain is stored in the hopper. An auger delivers the pellets to the burn grate. The fuel rate, or heat output, is set by

Memory &

Fan Trim

as desiredas desired

switch, controlled to run on high when the stove reaches higher temperatures and then resume the speed you had selected once it cools to a lower temperature.

Your stove can run efficiently over extended periods of time and at different heat output levels as long as the fuel supply is uninterrupted and timely cleaning and maintenance is preformed. An example of how improper cleaning effects operations is; the exhaust pressure switch will shut the pellet supply off and your stove will shut off if the exhaust system becomes plugged.

PelPro Home & Shop Heater www.pelprostoves.com 6

adjusting the feed rate touch pad, (settings 1 to 4). A fan provides combustion air to the burn grate. The amount of combustion air in the burn grate is adjustable and automatically changes as the fuel rate changes. The higher the fuel rate, the larger the amount of combustion air and visa versa. The fuel burns in the burn grate, producing heat. Some heat radiates out the front of your stove. The majority of the heat passes around the heat exchange tubes and air plenum around the firebox and is then moved into the room by the room air fan. A small amount of heat must pass out the exhaust of your stove, along with gases, into the atmosphere.

Your stove's heat output can be adjusted from setting 1-4, through the FEED RATE touch pad, to vary your heat output from Low to High. The room air fan can be manually adjusted through the FAN SPEED to run faster or slower to correspond to the amount of heat being produced. The room air fan is also on a limit



Hopper Lid

Heat Tubes

Tub e Scraper

Window

Bu rn G ra te

Burn Pot

Ash Pit

Hopper

Auger

uger Motor

Fa n M otor s

Exhaust

ir Intake

Base

UTOMATIC

AFETY

EATURES

L120 LOW LIMIT SWITCH

This limit switch is mounted on the exhaust blower housing and has 2 main functions:

Should the fire happen to go out, for any reason, this limit switch will shut the stove off when the exhaust

temperature drops below 120° F.

Upon starting the appliance, the AcuTron control board has a 15 minute “Lighting Mode”, if the stove

exhaust does not reach 120° F in that 15 minutes the stove will shut off. As soon as the stove exhaust does reach 120° F, the limit switch opens and the AcuTron enters a 5 minute “Safety Delay” mode.

F140 FAN LIMIT SWITCH

Your pellet appliance has a convection fan control limit switch. The room air fan's (F140) temperature limit snap switch automatically operates the fan on high when your stove is producing heat faster than the fan is carrying it into the room. This may occur when the heat control lever is set at [3 or 4] and the FAN SPEED is set to a very low or off setting. After the fan runs at this automatic high setting a few minutes, it may cycle back to its lower setting and may continue to cycle between [HIGH] and your selected setting. The circulation (room air) fan cycling from high to low is a normal condition as well as a safety feature of your appliance. To compensate for the fan cycling, adjust the FAN SPEED to a higher setting.

L250 HIGH LIMIT SWITCH

Your pellet appliance has a high temperature limit switch installed. If the temperature at the back of the firebox reaches approximately 250° F., the switch will shut off the electricity going to the Vacuum Switch and to the Auger Motor. The auger will automatically stop, and the appliance will shut down when the exhaust temperature cools (120° F). If this happens call your dealer or Dansons Customer Service (1-866-456-9269).

IT IS IMPORTANT TO FIND THE REASON WHY THE UNIT OVERHEATED.

VACUUM SWITCH

This safety device (mounted on the back panel pillar) detects vacuum in the exhaust system, firebox, and air intake. If the exhaust blower fails, the vent pipe becomes plugged, the viewing door is open, or if you are out of pellets, this switch will sense that there is a lack of vacuum and will stop the auger from continuing to feed pellets.

HOPPER LID SWITCH

This device is mounted inside the hopper.and is connected to the auger feed system.

If the hopper lid is OPEN the switch

WILL STOP THE AUGER FEED SYSTEM. This is to prevent fingers,

clothing or other objects from coming in contact with the auger.

The auger is capable of causing serious injury and this switch MAY NOT be disconnected.

Exhaust

Vacuum Switch

High Limit L250

Low Lim it L120

Fan Limit F140

Air Intake

Left Hand Side View / Exhaust Fan Side

If the power does go out, the pellet appliance will stop running. When the power comes back on, the stove will remember the function it was performing and return to that function.

Combustion Fan

Acu Tron Wiring Harness

PelPro Home & Shop Heater www.pelprostoves.com 7

HEATING SPECIFICATIONS

PECIFICATIONS

Approx. Heating capacity (sq. feet) * 800 – 2,000 Approx. Fuel burn rate per hour ** 1.5 – 5 lbs Hopper Capacity - Home 120 120 lbs Approx. Burn time at lowest setting 90 hrs

Hopper Capacity – Home 300 300 lbs. Approx. Burn time at lowest setting 200 hrs

¹ Heating capacity will vary depending on floor plan layout of your home, degree of insulation, and

the outside temperature. Fuel size, quality, density and moisture level will also have an effect.

¹¹ Pellet size may affect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as

much as 20%. Use PFI listed fuel for best results.

DIMENSIONS

24”

46 1/2”

26”

8 1/4”

Exhaust

PelPro Heater 300

PelPro Heater 120

24”

Weight

272 lbs.

225 lbs.

31 1/2”

26”

8 1/4”

14 1/4”

PelPro Heater 300

3 3/4”

Air Inlet

14 1/4”

Common for

all model

8 3/4”

PelPro Heater 120

3 3/4”

2” Air Inlet

Exhaust

8 3/4”

ELECTRICAL SPECIFICATIONS

Electrical Rating = 115 Volts 60 HZ 2.0 Amps Watts (operational) = 175 (approximately) Watts (optional igniter) = 475 (approximately)

A voltage surge protector or ground fault outlet is required for this unit. The warranty on the circuit board will be voided if surge protection is not installed before operating this unit.

If power outages or disturbances are a concern, you may wish to purchase a gas powered generator, solar or battery back-up system. Ensure that it is a “Positive” sign wave and a minimum 1000 watts continual, as well as surge protection.

EPA COMPLIANCE

This heater is exempt from EPA Phase II requirements, but has been tested for emissions using EPA test methods by Warnock Hersey , US. Pellet appliances that are designed with the combustion air supply exceeding 35:1 (by ratio) are exempt from EPA regulations.

PRODUCT IS SUBJECT TO CHANGE WITHOUT NOTICE.

PelPro Home & Shop Heater www.pelprostoves.com 8

LANNING

Unless you are knowledgeable and experienced in stove installation, we recommend your PelPro Appliance receive a Pre-delivery Check and be installed by your local Specialty Retailer, NFI (Natio nal Fireplace Institute) Pellet Specialist (USA) or WETT Certified Installer (CAN) .

COMPLETE THIS CHECK LIST PRIOR TO INSTALLING YOUR MULTI-FUEL APPLIANCE:

_____ Carefully read this "Owners Manual”. SAVE THIS MANUAL. _____ Have your local Dealer demonstrate all the operational, cleaning and maintenance steps

_____ Select a location. The design of your home and the stove placement will determine its value

Existing Chimneys, Pellet Fuel Storage, Aesthetic Considerations, Roof Design (rafter

_____ The installation of this appliance must conform to local codes and applicable state and

_____ Sign and keep a copy of the Pre-delivery Check List supplied by your Authorized Dealer, OR

______ Attach your proof of purchase to this manual and keep on hand for warranty.

COMPLETE THIS CHECK LIST WHILE INSTALLING YOUR MULT—FUEL APPLIANCE:

_____ Carefully read the ENTIRE installation section first. Twice is better. _____ Read the Installing Freestanding, Insert or Built-In sections. _____ Determine the location and measurement needed your chosen location. _____ Be sure to pre-fit all items before you install, fasten or install the stove permanently.

Remember measure twice, cut once. _____ Ensure ALL joints of “PL” vent and single wall stainless steel liner are tightly connected,

COMPLETE THIS CHECK LIST PRIOR TO LIGHTING YOUR FIRST FIRE:

_____ Obtain final inspection and approval by local building officials. _____ Carefully clean all marks off the brass, nickel or pewter parts before the first fire is lit. Use a

_____ Polish the hopper to remove the oil type coating used in manufacturing. _____ The high temp. stove paint used on your stove may take several hours of burning at a high fuel set-

_____ Review and follow the Lighting and Controls Instructions. _____ Ensure that appliance is connected to a surge protection unit. _____ Fill the hopper with quality pellets, Close the Hopper Lid

(figure 5), PUSH the FEED RATE Touch Pad and this will start the auger and the combustion fan.

necessary for your stove.

as a source of heat. A pellet appliance depends primarily on air circulation to disperse its heat. There are other practical considerations, which must be considered before a final placement is decided on:

locations & roof pitch), Room Traffic, Clearances to Combustibles, and Existing Wiring.

federal requirements. Becoming familiar with these requirements before installation is es-

sential.

“Dansons Certified Installer”, found inside our appliance or available online.

sealed with RTV Silicone or Hi-Temp foil tape, including to the exhaust connector, and

is correctly installed. (Follow vent manufacturer’s instructions.)

soft cloth and a gentle type cleaner. Caution: Never use an abrasive cleaner on any part of your stove.

ting to fully cure. During this time an odor, which is not harmful, may be evident. The area around the stove should be well ventilated.

NSTALLATION

& I

NSTALLATION

HECK

, Using the CCI “AcuTron”,

IST

PelPro Home & Shop Heater www.pelprostoves.com 9

LANNING

PELLET VENT MUST MAINTAIN A MINIMUM 3” CLEARANCE TO ANY COMBUSTIBLE

(INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER).

DO NOT CONNECT THE PELLET VENT TO A VENT SERVING ANY OTHER APPLIANCE OR

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.

—EE

—

XHAUST

STOVE.

YSTEMS

PELLET VENT TYPE:

1. Must be an approved 3” or 4” Diameter Type ”PL” vent, vented to the outside (fig. 7) or connect the vent to a factory built type “A” chimney using an adaptor.

2. Exception: A single wall “All Fuel” Stainless Steel chimney liner may be used inside a fireplace or fireplace installations (fig. 8) .

3. Some venting manufactures do make “PL” vent for use with wood pellet fuel only and another type of “PL” vent for corn or bio mass fuels. If in doubt, plan for the future and use the corn or multi-fuel

4. Use 4” dia. vent if vent or liner height is over 15’ or if installation is over 3.000’ above sea level. NOTE: 4” diameter vent may be used in all installations. If in doubt, use 4” dia. vent.

VENT SAFETY PRECAUTIONS:

A “Clean Out Tee” (4) must be installed at the bottom of all vertical runs. These “Tee’s” are to assist in periodically cleaning the vent. Single or Double clean out tees may be used. The exhaust system must be installed so the entire system can be cleaned without disassembly.

Termination must exhaust above the fresh air inlet

elevation, and parallel or above the exhaust output

of the multi-fuel appliance. It is highly recommended that at least 3 feet of vertical

pipe (5) be installed to create some natural draft. This is to help prevent the possibility of smoke or odor during the appliance shut down.

Horizontal sections must have a 1/4” rise every 12” of

travel after 3’ long.

Pellet vent connections must be sealed gas tight. Use

Hi-Temp RTV Silicone, good for over 600° F or Hi-temp

Metal foil tape, that meets UL181 standards,. DO NOT use “Duct Tape”.

Seal each vent section by injecting a liberal amount of sealant into the gap and/or wrap with foil tape.

It is strongly recommended that the exhaust system

be terminated on the prevailing wind side of the home.

Appliance may not be placed in, or vented through

a gas fireplace..

5 4

PelPro Home & Shop Heater www.pelprostoves.com 10

LANNING

— EE

—

XHAUST

YSTEMS

…

CONTINUED

…

CONTINUED

DETERMINE VENTING SIZE AND DISTANCE:

It is recommended that the vent system be installed with a minimum of three (3’) of vertical rise above the appliance exhaust port.

Equivalent Vent Length (EVL) is the method of determining vent sizes and lengths, that takes into account the effect of different component parts on air flow.

STEP 1 To help you determine the correct size and/or run, simply fill in the chart below.

Pellet Venting

Component

90 Degree or Tee X 5

45 Degree X 3

Horizontal Pipe X 1

Vertical Pipe X .5

Total Equivalent

# of Elbows

OR feet of Pipe

Multiply by Equivalent

Feet

Component

Equivalent

Step 2

less than 30.

Ensure the Total Equivalent is or is

Step 3 Use the Sizing Chart to determine

the proper venting size according to the Total Equivalent and the Altitude above sea level.

NOTE: In some cases it may be necessary

to contact Dansons Customer Service personal to determine acceptable venting configurations and altitude adjustments

1-877-303-3134.

The diagram to the right will help to give you a visual reference.

Maximum venting height is 33’. Maximum horizontal offset is 10’. Use the Equivalent Vent Length

Chart to determine proper combination of component parts.

Vent must have a support bracket every 5’ when on

the exterior wall.

Vent height and run

exceed the distance

not

shown in the un-shaded region of chart.

To achieve optimum performance, keep vent runs as short as possible. Especially on horizontal installations.

e e

F n

i h

g n e

L e

i P t n e

l a

i u q

3 or 4 Inch Diameter Pipe

0 1 2 3 4 5 6 7 8 9 10

Alt itude i n Thousands of Feet

must

4 Inch Diameter Only

Use Diameter “PL” Vent

4”

If venting outside of shaded area.

Use or Diameter

3” 4”

“PL” Vent, if venting in shaded area.

33’

30’

25’

20’

15’

10’

5’

0’

5’

PelPro Home & Shop Heater www.pelprostoves.com 11

10’

…

LANNING

— EE

—

XHAUST

YSTEMS

CONTINUED

…

CONTINUED

PELLET VENT TERMINATION: (Figures 7 & 8)

Termination must be a minimum of 12” above the chase cap (B) (note: the chimney must meet local codes for height above the roof or other obstructions)

Must have an approved cap (G) (to prevent water from entering) or a 45* elbow downturn (F)

If the termination is located on a windy side of house, an approved house shield is recommended to prevent soot from accumulating on the side of the house.

Must not be located where snow or other materials such as leafs, snow or grass, could block it.

Must have a “Metal Seal Plate” or “Wall Thimble” at point (A)

Figure 7 Figure 8

VENT TERMINATION CLEARANCES:

NOTE: Horizontal terminations must protrude 12” from the wall, vertical terminations 24”

Inside Corner

Detail

3’

2’

10’

A Minimum 4’ clearance below or beside any door or window which opens. B Minimum 1’ clearance above any door or window that opens. C Minimum 3’ clearance from any adjacent building. D Minimum 7’ clearance above any grade when adjacent to public walkways. E Minimum 2’ clearance above any grass, plants, or other combustible material. Minimum 1’ clearance above grade. F Minimum 3’ clearance above any forced air intake of any other appliance within 6’. G Minimum 2’ clearance below eves or overhang. H Minimum 1’ clearance horizontally from combustible wall I Minimum 1’ clearance to inside corner X Must be a minimum of 36” above the roof and 24” above the highest point of the roof within 10’.

NOTE: The following are not found on the above diagram.

• Minimum 3’ above a gas meter/regulator within 3’ horizontally of the vertical centre line of regulator.

• Minimum 6’ clearance to a gas service regulator vent outlet.

• Minimum 1’ clearance under veranda, porch, deck or balcony. Permitted only if structure is fully open on

a minimum of two sides beneath the floor.

PelPro Home & Shop Heater www.pelprostoves.com 12

+ 28 hidden pages

PelPro Wood Pellet Stoves HHPP2, HSPP2, HSPP3, HHPP3 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual