Installation and servicing should be done only by qualified service personnel and conform to all local codes.
Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only an
installed where exposed to rain and moisture.
Only use replacement parts recommended by Pelco.
After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify the
exposed parts have not been connected to line circuitry.
The installation method and materials should be capable of supporting
combination.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit.
This symbol indicates that there are important operating and maintenance instructions
in the literature accompanying this unit.
To reduce the risk of electrical shock, do not remove cover. No user serviceable parts
inside. Refer servicing to qualified service personel.
four times the weight of the enclosure, pan/tilt, camera and lens
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
d it must not be
4C1431SM-B (7/09)
Description
Environmental enclosures in the EH5700 Series are used with Pelco’s pan/tilt units of fixed mounts. Environmental enclosures in the
EH5700L Legacy Series are used with Pelco’s PT780 Series pan/tilt unit.
MODELS
EH5700 SERIES
EH5723Environmental enclosure with rear-opening lid. Lid has gas spring to hold it open. 23-inch (58.42 cm) length.
EH5723-1EH5723 with 120 VAC thermostatically controlled heater and blower.
EH5723-2EH5723 with 24 VAC thermostatically controlled heater and blower.
EH5723-3EH5723 with 230 VAC thermostatically controlled heater and blower.
EH5729Environmental enclosure with rear-opening lid. Lid has gas spring to hold it open. 29-inch (73.66 cm) length.
EH5729-1EH5729 with 120 VAC thermostatically controlled heater and blower.
EH5729-2EH5729 with 24 VAC thermostatically controlled heater and blower.
EH5729-3EH5729 with 230 VAC thermostatically controlled heater and blower.
EH5700L LEGACY SERIES
EH5723L Environmental enclosure with rear-opening lid. Lid has gas spring to hold it open. 23-inch (58.42 cm) length. Obsolete.
EH5723L-1EH5723L with 120 VAC thermostatically controlled heater and blower.
EH5723L-2EH5723L with 24 VAC thermostatically controlled heater and blower.
EH5723L-3EH5723L with 230 VAC thermostatically controlled heater and blower.
EH5729LEnvironmental enclosure with rear-opening lid. Lid has gas spring to hold it open. 29-inch (73.66 cm) length. Obsolete.
EH5729L-1EH5729L with 120 VAC thermostatically controlled heater and blower. Obsolete.
EH5729L-2EH5729L with 24 VAC thermostatically controlled heater and blower. Obsolete.
EH5729L-3EH5729L with 230 VAC thermostatically controlled heater and blower. Obsolete.
C1431SM-B (7/09)5
OPTIONAL ACCESSORIES
BK57-1Blower kit, 120 VAC, 15 watts
BK57-2Blower kit, 24 VAC, 10 watts
BK57-3Blower kit, 230 VAC, 15 watts
HK57-1Heater kit, 120 VAC, 90 watts
HK57-2Heater kit, 24 VAC, 50 watts
HK57-3Heater kit, 230 VAC, 70 watts
O/I-LPPPreset position lens wire harness (must be used with O/I-PCB)
O/I OUTLET120 VAC electrical outlet (must be used with O/I-PCB)
O/I-PCBCircuit board with thermostats
SS5723Sun shroud for EH5723 Series enclosures
SS5729Sun shroud for EH5729 Series enclosures
TI57Thermal insulation kit for EH5723 and EH5729 Series enclosures
WD57-1Window defroster and defogger kit, 120 VAC, 30 watts
WD57-3Window defroster and defogger kit, 230 VAC, 30 watts
WD57-2Window defroster and defogger kit, 24 VAC, 30 watts
WW5723-1Window wiper kit, 120 VAC, 15 watts, EH5723 Series enclosures
WW5723-2Window wiper kit, 24 VAC, 15 watts, EH5723 Series enclosures
WW5723-3Window wiper kit, 230 VAC, 15 watts, EH5723 Series enclosures
WW5729-1Window wiper kit, 120 VAC, 15 watts, EH5729 Series enclosures
WW5729-2Window wiper kit, 24 VAC, 15 watts, EH5729 Series enclosures
WW5729-3Window wiper kit, 230 VAC, 15 watts, EH5729 Series enclosures
6C1431SM-B (7/09)
Maintenance
Perform the following maintenance at regularly scheduled intervals to prolong the operational life and appearance of the equipment.
1. Clean the window with a mild non-abrasive detergent in water and a soft cloth to maintain picture clarity.
2. If your enclosure has a blower, clean the foam filters as follows:
a.On the bottom front of the enclosure, remove the two screws in the vent grill.
b.Remove the vent grill and take out the filters.
c.Clean the filters with warm water and mild detergent, dry thoroughly, and replace them in the grill.
d.Reinstall the vent grill.
To order replacement filters, use the part number EH550010045.
C1431SM-B (7/09)7
Exploded Assembly Drawings
F
K
14
A
E
15
11
J
B
D
16
A
13
24
TO UPPER WINDOW
F
BRACKET NUTS
A
E
10
12
TO STUD INSERTS
IN LID
9
8
7
6
19
G
H
22
5
C
L
20
21
B
17
A
25
1
26
18
A
M
4
A
27
28
A
B
3
B
2
23
29
B
30
SCREWS
SUPPLIED
WITH VENT
COVER
PLATE
INTERNALLY MOUNTED TO REAR OF HOUSING
ON BASIC UNIT. BASIC UNITS COME WITH VENT
COVER PLATES INSTALLED. -1, -2, AND -3 UNITS
COME WITH #30 AND #23 INSTALLED.
Figure 1. EH5700 Exploded Assembly Diagram
8C1431SM-B (7/09)
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.