Pelco WP13 User Manual

®

WP13

Wall Plate

Installation/Operation

Manual C205M (10/91)

1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be

observed.

1. Installation and servicing should only be done by Qualified Service Personnel
and conform to all Local codes.

2. Installation shall be done in accordance with all local and national electrical
and mechanical codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four (4)
times the maximum specified load.

4. Use stainless steel hardware to fasten the mount to outdoor surfaces.

5. T o pre vent damage from water leakage when installing a mount outdoors on a
roof or wall, apply sealant around the bolt holes between the mount and mount­ing surface.

The product and/or manual may bear the following
mark:

This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this
unit.

Please thoroughly familiarize yourself with the information

in this manual prior to installation and operation.

Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • [phone] or (1-559) 292-1981

FAX [phone] or (1-559) 292-3827

International customers call (1-559) 292-1981 or FAX [phone]

2.0 DESCRIPTION The WP13 is a wall plate specifically designed to be used with the Model

CM1300 camera mount when attaching to a standard 2" x 4" electrical junction
box.

3.0 INSTALLATION To install the WP13, perform the following steps:

1. Fasten the WP13 wall plate to the electrical box using two #6 flat head screws.
Be sure to first pass the wiring through the two half-inch diameter feedthrough
holes provided.

2. Fasten the CM1300 camera mount to the wall plate through the keyhole slots
provided using two #8-32 socket head screws.

3. Complete the installation of the camera mount as per manual #C216M.

2 Pelco Manual C205M (10/91)

4.0 SPECIFICATIONS Construction: 0.047"Aluminum

Dimensions: 2.75" x 4.5"
Finish: Polyester powder coat
Environment: Indoor

Pelco Manual C205M (10/91) 3

5.0 WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workman­ship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

• Three years on Camclosure
CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X camera models, which have a five-year
warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy
fixed dome products.

• Two years on Spectra®, Esprit®, ExSite™, and PS20 Scanners, including when used in continuous
motion applications.

• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and
Endura™ Series distributed network-based video products.months on DX Series digital video
recorders, NVR300 Series network video recorders, Endura™ Series distributed network-based video
products, and TW3000 Series twisted pair transmission products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a
period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications
(that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All
goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made
necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the spe­cific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of
contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable
for any special, incidental or consequential damages (including loss of use, loss of profit and claims of
third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional
rights, which are subject to variation from state to state.

®

Series products (multiplexers, server, and keyboard).

®

and fixed camera models, except the CC3701H-2, CC3701H-2X,

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone] to
obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty condi-

tions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by

Pelco.
RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)
289-9100 or [phone] to obtain an authorization number (CA number if returned for credit, and
RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and
freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to
return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco.
™ Endura and ExSite are trademarks of Pelco. © Copyright 1997, Pelco. All rights reserved.

4 Pelco Manual C205M (10/91)