Pelco WM3026 User Manual

C258M-A (4/00)
WM3026
Heavy-Duty Wall Mount

®

3500 Pelco Way,
Clovis, CA 93612-5699
USA

In North America & Canada:
Tel [phone]
FAX [phone]

International Customers:
Tel [phone]
FAX [phone]

www.pelco.com

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service and installation personnel.

2. Installation shall be done in accordance with all local and national electrical and mechanical
codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maximum
specified load.

4. Use stainless steel hardware to fasten the mount to outdoor surf aces.

5. To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.

The product and/or manual may bear the follo wing marks:

This symbol indicates that there are important operating and maintenance instructions
in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.

DESCRIPTION

The WM3026 Wall Mount will support a heavy-duty enclosure and/or pan/tilt. The wall mount will
hold loads up to 300 pounds (136.08 kg) when directly attached to any vertical load-bearing
structure.

INSTALLATION

Mounting to Surface

To install the WM3026 perform the following steps:

1. Determine the mounting location. The mounting surface should be able to support four
times the combined weight of the mount, pan/ tilt, camera and enclosure.

2. Use the flanged end of the WM3026 as a template and mark the six fastener hole positions
onto the mounting surface. Set the WM3026 mount to the side and prepare the holes for the
fasteners.

3. Use one of the following methods to prepare the wiring/cabling for power. Refer to Figure 1.
a. Thread wiring/cabling through the mount arm and exit through the top feedthrough

hole.

b. Thread the wiring/cabling through one of the 3/4-inch NPT holes on the side of the

mount arm and out the top feedthrough hole. Flexible, metal conduit connectors can
be used.

c. Bypass the mount and directly connect wiring to the camera, enclosure and/or pan/tilt.

Fold the wiring out of the way and secure.

4. Position the WM3026 mount ov er the mounting holes. Secure with a minimum of six, 3/8-inch
fasteners of appropriate length (not supplied). If you install the WM3026 outdoors, seal the
fastener holes with an appropriate sealant to prevent water damage. Apply the sealant be­tween the mount and the mounting surface.

Camera/Enclosure Mounting

To install the camera and/or enclosure directly to the mount, refer to Figure 1 and do the following:

1. Center the camera and/or enclosure on the tilt table.

2. Attach the camera and/or enclosure to the tilt table with 1/4-20 flat head fasteners (not pro­vided).

3. Connect wiring/cabling to the camera and/or enclosure. Refer to the manual supplied with
the equipment for more information.

4. Loosen the hex head bolts on the top and lower brackets of the tilt table. Adjust the pan and
tilt to the desired settings. Tighten bolts and lock into place.

Pan/Tilt and Camera/Enclosure Mounting

To install the pan/tilt, camera and/or enclosure directly to the mount, refer to Figure 1 and per­form the following steps:

1. Remove the tilt table from the WM3026.

2. Center the pan/tilt, camera and/or enclosure on the pan/tilt adapter. Position as needed to
align mounting holes. Secure the load to the mount using appropriate fasteners (not sup­plied). Refer to the manuals supplied with the equipment for more information.

3. Connect wiring /cabling to the camera, enclosure and pan/tilt. For proper installation of wiring/
cabling, refer to the manuals supplied with the equipment. Be sure to leave an adequate
loop of cables to prevent binding and/or strain where applicable.

Receiver Mounting

To mount a receiver to the gusset of the WM3026 refer to Figure 1 and do the following:

TILT TABLE ASSEMBLY
(TOP & LOWER BRACKETS)

PAN/TILT ADAPTOR

1. Line up the mounting holes on the receiver with the mounting holes on the gusset.

ing holes are six inches apart. If the receiver’s mounting holes are

not

six inches apart,

Mount-

attach it to a flat, vertical surface. Refer to the manual supplied with the receiver.

2. Attach the receiver to the gusset using 1/4-inch fasteners (not supplied) of the appropriate
length.

3. Use the four cable tie holes located on the bottom edge of the gusset (cable ties not in­cluded) and secure the wiring/cabling.

HEX HEAD BOLTS

TOP FEEDTHROUGH HOLE

FASTENER HOLE

ARM

GUSSET

CABLE TIE HOLE

3/4-NPT
THREADED
HOLE

RECEIVER MOUNTING
HOLES

Figure 1. WM3026 Heavy-Duty Wall Mount