Pelco EURACK, USRACK installation manual

INSTALLATION AND OPERATION MANUAL

EU/USRACK

RACK MOUNT CARD CAGE WITH POWER SUPPLY

This rack’s integral 115/230 VAC power supply provides for the elimination of a

single-point failure in the event of a major fault within any module located within

the chassis rack, through the use of automatic electronic current limiting within

each rack-mountable module.

In the power supply design only the faulty module shuts down, and the operation

of the other modules within the rack continue unimpaired. This automatic

current limiting feature is also self-resetting, should the fault or overload be of a

temporary or intermittent condition.

The power supply is intended to be installed in the Pelco Card Cage only. Any

other applications are not supported. See Page 3 for installation instructions.

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C5637M-A / REV 07-24-14

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit
from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.

14. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the
apparatus.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

16. Installation should be done only by qualified personnel and conform to all local codes.

17. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must
not be installed where exposed to rain and moisture.

18. Use only installation methods and materials capable of supporting four times the maximum specified load.

19. A CCC-approved power cord must be used to power this equipment when used in China.

20. In order to satisfy the EU Regulatory compliance Standards, the use of a universal power supply (UPS) is required on the AC mains.

21. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C5637M-A / REV 07-24-14

INSTALLATION AND OPERATION MANUAL EU/USRACK

EURACK

FORCONTINUED

PROTECTIONAGA INST RIS K

OF FI RE, REPLACEONLY

WITH SAME TYPE FU SE

CAUTION

!

Input: 90-264 VAC

@1.0Am ps5 0/60 Hz
Fuse:1.250ASB, 250VAC
Output:9.0 VDC@6.5Amps
Model: EUPS
File Number:E354877

CN-9-A-EUPS

POWER

FIGURE 1 – RACK INTEGRAL POWER SUPPLY

REAR PANEL (In Rack)FRONT PANEL (In Rack)

RED or
BLACK WITH
WHITE STRIPE
BLACK

ELECTRICAL

Input Voltage: 90-264 VAC @ 70 W Maximum

Output Voltage: 9 VDC +/- 5% @ 6.5 Amps @ 75˚C

Detachable, IEC-connected AC Line Cord allows easy field
replacement or exchange for various worldwide AC power plug
configurations (use only manufacturer’s supplied cord).

FIGURE 2 – LED INDICATORS

POWER

RED Unit powered up

OFF Unit powered down

SPARE 1.25A
SLOW BLOW FUSE

CHASSIS
GROUNDING STUD
(6-32 Thread)

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C5637M-A / REV 07-24-14

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

•Five years:
–Fiber optic products
– Unshielded Twisted Pair (UTP) transmission products
–CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models

• Three years:
–FD Series and BU Series analog camera models
–Fixed network cameras and network dome cameras with Sarix
–Sarix thermal imaging products (TI and ESTI Series)
–Fixed analog camera models (C20 Series, CCC1390H Series, C10DN Series,

and C10CH Series)
– EH1500 Series enclosures
–Spectra
–Spectra HD dome products
–Camclosure

®

IV products (including Spectra IV IP)

®

IS Series integrated camera systems

– DX Series video recorders (except DX9000 Series which is covered for a

period of one year), DVR5100 Series digital video recorders, Digital Sentry

Series hardware products, DVX Series digital video recorders, and NVR300

Series network video recorders

®

– Endura
– Genex

Series distributed network-based video products

®

Series products (multiplexers, server, and keyboard)
– PMCL200/300/400 Series LCD monitors
–PMCL5xxF Series and PMCL5xxNB Series LCD monitors

•Two years:
–Standard varifocal, fixed focal, and motorized zoom lenses
– DF5/DF8 Series fixed dome products

®

–Legacy
–Spectra III

Series integrated positioning systems

™

, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, ExSite IP, and

PS20 scanners, including when used in continuous motion applications
– Esprit Ti and TI2500 Series thermal imaging products
– Esprit and WW5700 Series window wiper (excluding wiper blades)
–CM6700/CM6800/CM9700 Series matrix
– Digital Light Processing (DLP

®

) displays (except lamp and color wheel). The
lamp and color wheel will be covered for a period of 90 days. The air filter is
not covered under warranty.

®

technology

•Six months:
– All pan and tilts, scanners, or preset lenses used in continuous motion

applications (preset scan, tour, and auto scan modes)

Pelco will warrant all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid
to a Pelco designated location. Repairs made necessary by reason of misuse,

alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s liability
for any claim, whether based on breach of contract, negligence, infringement of
any rights of any party or product liability, relating to the Products shall not exceed
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be
liable for any special, incidental, or consequential damages (including loss of use,
loss of profit, and claims of third parties) however caused, whether by the
negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization

®

following information:

number (RA), and provide the

1. Model and serial number

2. Date of shipment, P. O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall under
the warranty conditions stated above, please include a written explanation with
the product when returned.

Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at [phone]
or [phone] to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and
refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned
CA or RA number and freight should be prepaid.

Revised 1-12-12

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pe .cnI ,ocleP ,2102 thgirypoC © .setailiffa sti ro .cnI ,ocl
All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.

www.pelco.com

Pelco, Inc. 625 W. Alluvial Fresno, California 93711

United States USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone]